FSR WB-CMU-6G User manual

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - FAX 973.785.4207

FSR

WB-CMU-6G Box Installation Instructions

CONDUITS AND CONDUIT

FITTINGS AS REQUIRED

CONCRETE BLOCK

WALL BOX

COVER

WB-CMU-6G

CONSTRUCTION BE

SCREW MUST

FLUSH WITH

FRONT SURFACE

OF BOX

4.00

7.63

BLOCK

MUST

OR BOX CAN BE ROTATED AS

TO THE FULL BLOCK WEB. BLOCK

BLOCK WEB

WITH CONCRETE

BE FLUSH

NEEDED.

FULL LENGTH

THE BOX MUST BE LOCATED NEXT

THE LOCATION OF THE KNOCK OUT

THAT IS CLOSEST TO THE EDGE OF

FRONT SURFACE OF

BOX

MODIFIED

CONCRETE BLOCK

WALL BOX INSTALLATION

REMOVE CONSTRUCTION COVER FROM BOX. INSERT CONDUIT FITTINGS AND CONDUIT INTO BOX. RE-1.

INSERT CONSTRUCTION COVER WITH SUPPLIED HARDWARE BEFORE ANY MORTAR IS APPLIED TO THE

BOX.

A MODIFIED CONCRETE BLOCK WILL NEED TO BE CUT AS SHOWN BELOW. 2.

PLACE THE WALL BOX ON THE BLOCK WALL, ENSURING THE FRONT SURFACE OF THE WALL BOX IS FLUSH

WITH CONCRETE BLOCK WALL. ENSURE MORTAR IS APPLIED TO TOP, BOTTOM, SIDES AND ALL BLOCK

WEBS. ALL SEAMS AROUND THE WALL BOX SHOULD BE FILLED WITH MORTAR.

NOTE** IT IS IMPORTANT THAT THE CONSTRUCTION COVER IS INSTALLED ON WALL BOX PRIOR TO PLACING THE WALL BOX

ON THE BLOCK WALL AND BEFORE ANY CONCRETE BLOCKS ARE PLACED ABOVE THE UNIT.

43449 LIT1863

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - FAX 973.785.4207

FSR

WB-CMU-6G Box Installation Instructions

P/N - 54287

Medium Divider Holder - Medium Gang Spacer -

P/N - 55639

Divider

P/N - 55865

Small Divider Holder -

GANG SPACER / DIVIDER HOLDER PLATES

ELECTRICAL INSTALLATION

DISCARD CONSTRUCTION COVER AND HARDWARE, CURRENTLY MOUNTED ON WALL BOX. 1.

GANG PLATE TRIM RING IS CONFIGURABLE IN MULTIPLE GANG PLATE CONFIGURATIONS, AND CAN BE 2.

ROTATED 180 . ASSEMBLE GANG PLATE TRIM RING USING THE GANG SPACER, DIVIDER HOLDER, AND

DIVIDER PROVIDED, AS NOTED ON PAGE 3 & 4. DIVIDER NEEDS TO BE POSITIONED ON THE DIVIDER

HOLDER, IN AN ORIENTATION THAT WILL NOT INTERFERE WITH KNOCK OUT AND CONDUIT. THE INTERNAL

FACE OF THE DIVIDER SHOULD ALWAYS FACE THE CENTER PLANE OF THE BOX. SEE ILLISTRATION BELOW.

AFTER THE GANG PLATE TRIM RING IS ASSEMBLED IN THE CORRECT GANG PLATE CONFIGURATION WITH A 3.

DIVIDER IF NECESSARY, INSTALL THE GANG PLATE TRIM RING ASSEMBLY INTO THE FIXED WALL BOX.

ENSURE THE DIVIDER IS IN THE CORRECT ORIENTATION TO THE KNOCK OUT, BEFORE FULLY INSERTING THE

ASSEMBLY INTO THE WALL BOX. INSERT HARDWARE PROVIDED TO MOUNT THE GANG PLATE TRIM RING

ONTO THE WALL BOX

WIRE AS NECESSARY, ENSURING GROUND SCREWS ARE CONNECTED AT BACK OF BOX. INSTALL DEVICES 4.

AND WALL PLATES AS NEEDED.

NOTICE: FOR INSTALLATION BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL NATIONAL AND LOCAL

ELECTRICAL CODES.

DIVIDER IN LINE

WITH KNOCK OUT,

ENSURE THIS

ORIENTATION

GANG PLATE TRIM RING

Divider -

P/N - 51174

Internal Face -

This face will

always be facing

the Center plane

of the Box

43449 LIT1863

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - FAX 973.785.4207

FSR

WB-CMU-6G Box Installation Instructions

One Single Gang and One 4-Gang Plate

Two Single Gang and One 2-Gang PlateFour Single Gang Plates

GANG PLATE CONFIGURATIONS

GANG PLATE TRIM RING ASSEMBLY CAN BE ROTATED 180 FOR REVERSED APPLICATIONS. NOTATE THE ORIENTATION 1.

OF THE DIVIDER HOLDERS' FLANGES, IN THE ILLUSTRATIONS BELOW. THIS IS IMPORTANT TO THE ASSEMBLY OF THE

GANG PLATE TRIM RING.

NOTICE: FOR INSTALLATION BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL NATIONAL AND LOCAL ELECTRICAL

CODES

SMALL DIVIDER

HOLDER

55639 -

SS, ZNC

11511-

SCREW, 8-32X.25,

SCREW, 8-32 X .25,

LOW VOLT, STL,

DIVIDER, HIGH/

51174 -

SPACER

13330-

SS, PASSVTD

55865 -

MEDIUM GANG

54287 -

MEDIUM DIVIDER HOLDER

DIVIDER, HIGH/

LOW VOLT, STL,

SCREW, 8-32X.25,

11511-

55865 -

51174 -

SS, ZNC

SPACER

MEDIUM GANG

SMALL DIVIDER HOLDER

55639 -

.25, SS,

PASSVTD

8-32 X

13330-

SCREW,

51174 -

LOW VOLT, STL,

DIVIDER, HIGH/

SCREW, 8-32X.25,

11511-

SS, ZNC

MEDIUM DIVIDER HOLDER

54287 -

13330-

SCREW, 8-32 X .25,

SS, PASSVTD

.25, SS,

PASSVTD

8-32 X

11511-

One Single Gang and One 3-Gang Plate

SCREW,

DIVIDER, HIGH/ LOW VOLT, STL,

SCREW, 8-32X.25, SS, ZNC

51174 -

13330-

55639 -

SMALL DIVIDER

HOLDER

43449 LIT1863

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - FAX 973.785.4207

FSR

WB-CMU-6G Box Installation Instructions

MEDIUM GANG SPACER

SMALL DIVIDER

55865 -

HOLDER

55639 - 13330-

SCREW, 8-32 X .25,

SS, PASSVTD

HIGH/ LOW

HOLDER

VOLT, STL,

MEDIUM

13330-

55865 -

SS, PASSVTD

MEDIUM DIVIDER

54287 -

DIVIDER,

51174 -

SCREW, 8-32 X .25,

HOLDER

GANG

SPACER

DIVIDER

SMALL

55639 -

11511-

SCREW, 8-32X.25, SS,

ZNC

51174 -

13330-

SCREW, 8-32 X .25,

SS, PASSVTD

VOLT, STL,

HIGH/ LOW

MEDIUM DIVIDER HOLDER

54287 -

DIVIDER,

11511-

SCREW, 8-32X.25, SS,

ZNC

One 6-Gang Plate

One 2-Gang and One 3-Gang Plate

Two 2-Gang Plates

One 5-Gang Plate

GANG PLATE CONFIGURATIONS

GANG PLATE TRIM RING ASSEMBLY CAN BE ROTATED 180 FOR REVERSED APPLICATIONS. NOTATE THE ORIENTATION 1.

OF THE DIVIDER HOLDERS' FLANGES, IN THE ILLUSTRATIONS BELOW. THIS IS IMPORTANT TO THE ASSEMBLY OF THE

GANG PLATE TRIM RING.

NOTICE: FOR INSTALLATION BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL NATIONAL AND LOCAL ELECTRICAL

CODES

43449 LIT1863

FSR WB-CMU-6G User manual

Related papers

Other documents