FSR CB-12P Installation guide

Brand: FSR

Model: CB-12P

Category: Projector mounts

Type: Installation guide

FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207

43189 LIT1317B

POLE MOUNT

PLATE COVER

REMOVE POLE MOUNT PLATE COVER (COVER

SCREWS LOCATED IN INTERIOR OF CEILING BOX).

1a. 1b. REMOVE FLANGE AND MOVE TO ALTERNATE

LOCATION. CHANGE PLUG LOCATION ON THE POLE

MOUNT PLATE COVER AS REQUIRED, AND

RE-INSTALL THE PLATE COVER WITH THE (2)

ORIGINAL SCREWS.

(2) PLUG

1. PRIOR TO CEILING INSTALLATION, DETERMINE MOUNTING LOCATION

OF THE FLANGE FOR THE PROJECTOR MOUNT. IF DEFAULT FACTORY

LOCATION WILL BE USED, PROCEED TO STEP 2. IF CHANGING TO

ALTERNATE LOCATION, FOLLOW STEPS 1a THRU 1b.

NOTE: FLANGE LOCATION CAN BE CHANGED AFTER

CEILING INSTALLATION.

CB-12P INSTALLATION INSTRUCTIONS

MAKE SURE PROJECTOR

MOUNT SET SCREW IS

ORIENTED TOWARDS THE

ACCESS HOLE IN THE POLE

MOUNT PLATE

POLE MOUNT FLANGE

(4) #10 LOCK WASHERS

(4) #10-32 x 3/4" LONG

HEX SCREW

SET SCREW ACCESS HOLE POLE MOUNT PLATE

AVAILABLE KITS (SOLD SEPARATELY):

CB-MNT1 - CABLE INSTALLATION KIT

CB-THRD - THREADED ROD INSTALLATION KIT

NOTE: THREADED ROD IS THE

RECOMMENDED CEILING BOX

MOUNTING SUSPENSION

(SHOWN), TO MINIMIZE

FIXTURE TILTING DUE

TO THE WEIGHT OF ANY

SUSPENDED EQUIPMENT.

NOTE: MAXIMUM GROSS WEIGHT - 110 LBS

INSTALL CB-12P TO A STRUCTURAL CEILING ABLE TO

SUPPORT FIVE TIMES THE NOTED GROSS WEIGHT. USE

APPROPRIATE MOUNTING METHODS BASED ON LOCAL

BUILDING CODES. INSTALL SAFETY CABLE AS REQUIRED BY

LOCAL BUILDING CODES. ROUTE CONDUITS TO BOX AS

REQUIRED.

14 GA. STEEL TIE WIRE MAY BE USED

(SUPPLIED BY CUSTOMER OR USE FSR KIT)

AT 70,000 PSI TENSILE STRENGTH OR

BETTER AS REQUIRED BY BUILDING CODES.

NOTE: WIRES SUPPORT CEILING

BOX, AND ARE NOT SAFETY CABLES

THREADED ROD OR CABLE TO

BE PLUMB WITH CEILING AND FLOOR

ROUTE CONDUIT

(SUPPLIED BY

CUSTOMER) TO

KNOCKOUTS

AS REQUIRED

STRUCTURAL

MEMBER

ALL MOUNTING HARDWARE

SUPPLIED BY CUSTOMER

STRUCTURAL

CHANNEL

BRACKET - FSR'S

THREADED ROD

INSTALLATION KIT

(HARDWARE SUPPLIED

BY CUSTOMER)

COVER SCREWS LOCATED IN

INTERIOR OF CEILING BOX

PART OF

POLE MOUNT

PLATE COVER

FSR Inc.

244 Bergen Boulevard, Woodland Park, NJ 07424

Phone: 973.785.4347 - Fax: 973.785.4207

Web: www.fsrinc.com - E-mail: [email protected]om

10-3/4" x 15-1/4"

DROP CEILING

PANEL MATERIAL

(SUPPLIED BY

CUSTOMER)

3. INSTALL 10-3/4" x 15-1/4" DROP CEILING PANEL MATERIAL

INTO DOOR OF CB-12P. BEND CAPTURE TABS OVER

PANEL TO HOLD PANEL IN PLACE.

(4) CAPTURE TAB

LOOSEN SCREWS

TO OPEN CB-12P DOOR

DOOR IS

REMOVABLE.

(a) PUSH DOOR

UP TOWARDS

CEILING AND

(b) PUSH AWAY

FROM

PROJECTOR

PANEL MOUNT -

REVERSE

PROCEDURE

TO INSTALL

4. REMOVE SHELF AND MOUNT ELECTRONICS TO SHELF.

USE HOLE/SLOT PATTERN ON SHELF TO MOUNT

EQUIPMENT. ADDITIONAL HOLES MAY BE REQUIRED.

RE-INSTALL SHELF INTO CB-12P. MAKE ELECTRICAL

CONNECTIONS AS REQUIRED.

NOTE: MAXIMUM LOAD PER SHELF - 20 LBS EACH

LOOSEN SCREWS (4 PER SHELF)

TO REMOVE SHELVES

LOOSEN SHELF

SCREWS. (a) PUSH

SHELF TOWARDS

PROJECTOR

MOUNT AND (b) SHELF

WILL DROP DOWN OUT

OF CB-12P

(2) SHELF

5. INSTALL PROJECTOR MOUNT PIPE INTO CB-12P. SECURE

PIPE WITH SET SCREW. FINISH INSTALLATION PER

MANUFACTURER'S PROJECTOR MOUNT INSTRUCTIONS.

PROJECTOR MOUNT SET

SCREW ACCESS HOLE

PROJECTOR MOUNT PIPE

(SUPPLIED BY CUSTOMER)

NOTE: MAXIMUM PROJECTOR LOAD INCUDING MOUNTED ACCESSORIES - 50 LBS

DISCONNECT

SAFETY CABLE

TO COMPLETELY

REMOVE DOOR

NOTE: THE CENTER OF MASS

OF SUSPENDED EQUIP-

MENT MUST BE WITHIN

A 2.5" RADIUS OF THE

CENTER LINE OF THE

FLANGE MOUNT OF THE

CEILING BOX.

FSR CB-12P Installation guide

Brand: FSR

Model: CB-12P

Category: Projector mounts

Type: Installation guide

Download PDF

report

FSR CB-12P Installation guide

FSR CB-12P Installation guide

Related papers