FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
43027 LIT1433
BOX INSTALLATION - STEP 1
LOCATE AND POSITION BOX IN ACCORDANCE WITH FLOOR
PLANS. TOP SURFACE OF TEMPORARY COVER MUST BE SET
TO MATCH THE HEIGHT OF THE FINISHED FLOOR - ie STONE,
WOOD OR CONCRETE - SEE TYPICAL INSTALLATION HEIGHTS.
LEVEL AND ANCHOR BOX AS REQUIRED. USE SCREWS, NAILS,
OR WIRE TO PREVENT BOX FROM FLOATING DURING POUR.
REMOVE AND RETAIN TEMPORARY COVER AND SCREWS.
ROUTE CONDUITS TO BOX AS REQUIRED. GANG BRACKET
SCREWS MUST BE IN PLACE AND BOTTOMED TO ENSURE
SCREW VOIDS AFTER POUR. PLACE THIS INSTALLATION GUIDE
BACK INTO BOX, ALONG WITH ALL SUPPLIED ITEMS, AND
REINSTALL TEMPORARY COVER.
BOX INSTALLATION - STEP 2
SCREED TO TOP OF BOX SURFACE FOR 3/16" THICK
CARPET/FLOORING OR SPECIFIC HEIGHT TO ALLOW
FOR THICKER FINISHED FLOOR MATERIAL. HAND
TROWELING RECOMMENDED NEAR BOX EDGES.
BOX HAS NO HEIGHT ADJUSTMENT AFTER
CONCRETE POUR.
TEMPORARY
COVER
(8) #6-32 FLAT HEAD SCREW
CONCRETE SURFACE OR TOP
OF FINISHED FLOOR MATERIAL
CARPET OVER CONCRETE (COVER WITH BEVELED EDGING)
TYPICAL INSTALLATION HEIGHTS
(4) LEVELING BOLT
FL-605P INSTALLATION INSTRUCTIONS
INSTALLING ELECTRONIC COMPONENTS
PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF
GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE
WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL
ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.
REINSTALL TEMPORARY COVER IF FINISHED COVER IS TO BE
INSTALLED AT A LATER DATE.
INSTALLED
ELECTRONIC
COMPONENT
GANG
MOUNTING
BRACKET
(2) #8-32 x .25 LG
FLAT HEAD
SCREW
DIVIDER ASSEMBLY
GANG
MOUNTING
PLATE
(2) #8-32 x .375 LG
SELF TAPPING
PAN HEAD
SCREW
GANG PLATE ASSEMBLY
GANG DIVIDER ASSEMBLY
(2) #8-32 x .25 LG
PAN HEAD
SCREW DIVIDER HOLDER
DIVIDER
TILE OR THIN WOOD LAMINATE OVER CONCRETE (COVER WITH SQUARE EDGING)
CONCRETE
FLOOR BOX
TEMPORARY COVER
CARPET EDGING
FINISH COVER
FLOOR BOX
CONCRETE
CONCRETE
FLOOR BOX
TEMPORARY COVER
TILE OR THIN WOOD LAMINATE
CONCRETE
EDGING
FINISH COVER
FLOOR BOX
SCREED FLUSH
SCREED FLUSH GROUT/THINSET
DIVIDER HOLDER MUST BE ORIENTED AS SHOWN WHEN ATTACHING
TO DIVIDERS, IN ORDER TO PROPERLY ASSEMBLE BOX INTERIOR.
DIVIDER
HOLDER USED
AS SMALL GAP
FILLER*
LARGE GAP
FILLER*
* GAP FILLERS ARE OPTIONAL, PER DESIRED
CONFIGURATION (SEE PREVIOUS PAGE),
AND ARE INSTALLED SIMILARLY TO
DIVIDER ASSEMBLIES.
* DIVIDER ASSEMBLY FOR 6" BOXES
POSITION DIVIDER ASSEMBLY IN BOX BEFORE INSTALLING
GANG PLATE ASSEMBLY. SECURE DIVIDER ASSEMBLY TO
GANG PLATE ASSEMBLY WITH SCREWS AS NOTED.
GANG MOUNTING BRACKET CONFIGURATION
PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS
SHOWN BELOW AND REASSEMBLE INTO BOX.
REMOVABLE LARGE CENTER DIVIDER
REMOVABLE SMALL CENTER DIVIDER
REMOVABLE SMALL CENTER DIVIDER
REMOVABLE LARGE CENTER DIVIDER
CENTER DIVIDER CONFIGURATION.
SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.
REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE
CENTER DIVIDERS.
TYPICAL INSTALLATION HEIGHTS
WOOD WITH OR WITHOUT SLEEPER SYSTEM OVER CONCRETE (COVER WITH EDGING)
H
TEMPORARY COVER
FLOOR BOX
CONCRETE
TH
H
E
CONCRETE FLOOR BOX
FINISH COVER
EDGING
WOOD
H (BASED ON ASSEMBLY THICKNESS) =
TH (TOTAL ASSEMBLY HEIGHT) - E (EDGING HEIGHT)
WOOD WITH OR WITHOUT SLEEPER SYSTEM OVER CONCRETE (COVER WITHOUT EDGING)
H
H = ASSEMBLY THICKNESS
TEMPORARY COVER
FLOOR BOX
CONCRETE
WOOD
CONCRETE
FLOOR BOX
FINISH COVER
VINYL FLOORING OVER CONCRETE (COVER WITHOUT EDGING)
H
CONCRETE
TEMPORARY COVER
FLOOR BOX CONCRETE FLOOR BOX
FINISH COVER
VINYL FLOORING
SLEEPER
SYSTEM
(IF USED)
SLEEPER
SYSTEM
(IF USED)
VERIFY PER
SPECIFICATION
OR ORDER
POSSIBLE GANG DIVIDER LOCATION
6 GANG MOUNTING PLATE
DIVIDER HOLDER
OPTIONAL DIVIDER
LARGE GAP FILLER
DIVIDER HOLDER USED
AS SMALL GAP FILLER
"6 GANG SIDE" MOUNTING BRACKET CONFIGURATIONS
1G 3G 1G 3G
2G 2G 2G 2G
1G 4G
2G 3G 3G 1G
2G 2G
3G 2G 4G 1G 6G
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
FSR FL-600P-3-B Installation guide
-
-
-
-
-
-
-
-
-
FSR WB-CMU-6G User manual
Other documents
-
Legrand 10DP Operating instructions
-
Legrand 8CTHDBS Installation guide
-
Legrand 8ATC2PSB Installation guide
-
Allen Engineering TRTP275 User manual
-
Legrand 896 Owner's manual
-
Legrand 881AMD8CTCBS Operating instructions
-
-
Carlon A861 User manual
-
Hubbell Wiring Device-Kellems PD2515 Installation guide
-
FLEXCO 42VTR00P001 Installation guide
