i3-TRNG-CAMS-B85.indd
Rev. 230517
The B85 is an extension back box for cable management and can be used for surface,
pendant or horizontal wall mounting of i3’s M75 and M85 camera series.
• Back box for IP camera wire management.
• Suitable for outdoor and indoor installations.
• Six (6) pre-drilled hole dimples for surface mounting. Optional use with Pendant
Mount EMT Pipe 3/4” or DB60 Horizontal Wallmount bracket.
PACKAGE CONTENTS
In addition to this manual and B85 back box,
the packing box includes:
1. Round head screw, machine type x5
2. Round head screw, tapping type with O-ring x5
3. Plastic anchor x5
4. Surface Mount template x1
Back Box Mounting Base
B85
User Manual
DIMENSIONS
Pendant Mount
Rigid 3/4” EMT Pipe
(Optional)
B85
Back Box
DB60 Goose Neck
Wallmount Bracket
(Optional)
Add Sealant
Alignment
marks
M85
Camera
M85 Lexan
dome bubble
3/4” Electrical
EMT Conduit
Fitting
Scan this QR code or visit ftp.i3international.com to view i3
product manuals.
Contact our Technical Support team at: 1.877.877.7241 or
[email protected] if you have any questions or
concerns regarding camera installation or if you require
software services or support.
QR Code for Complete
User Manual and ACT
INSTALLATION NOTES
• To maintain IP67 waterproof rating, always use the waterproof RJ45 connector supplied with the camera.
• Ensure that the mounting surface and mounting hardware is suitable for the chosen installation method.
• When using with the DB60 or EMT pipe, remove RP1 first.
• If using the side conduit hole, replace the RP1 with the metal plug from the side conduit. Do not use the
rubber plug (RP1) in the side conduit hole.
• Always add sealant to all threads in outdoor installations (as shown in Figure B).
• If attaching directly to a surface, tighten the provided tapping screws to fully compress the ‘O’ ring.
• Use a network cable 5mm or more in diameter to create a good seal in RP1 (if using).
INSTALLATION
Use the security Torx bit or screwdriver (not provided) to loosen four screws securing the dome bubble to the
M75/M85 camera. Set the dome bubble aside.
Surface Installation
1. B85 comes with six 90% pre-drilled hole dimples. Depending on the type of installation and mounting
surface, complete drilling 2-3 holes.
2. Attach the mounting template (4) to the mounting surface.
3. Drill holes in the mounting surface, as marked on the template, to match the B85 holes pre-drilled in Step 1.
4. Insert anchors (3) into the holes.
5. (Skip this step if using the side conduit) Drill the conduit hole for the camera cable, as marked on the
template.
6. Secure the B85 back box to the mounting surface using the tapping screws with the O-ring (2).
Tighten to fully compress the ‘O’ ring.
7. Use the round head machine screws (1) to secure the mounting base to the back box.
8. Pull the camera’s cable into the B85 back box.
9. Adjust the lens assembly for the desired view and re-attach the dome bubble.
DB60 / Pendant Installation (Follow Figure B)
Note: Do not drill holes in B85 for this installation.
1. Remove RP1 from the B85 and pull the camera’s cable through the top conduit
opening and into the DB60 or the 3/4 EMT pipe.
2. Attach B85 to the DB60 or to the 3/4” EMT pipe (using a conduit fitting).
Add sealant to all threads as shown in Figure B.
3. Use the round head machine screws (1) to secure the camera body to the back box.
4. Adjust the lens assembly for the desired view and re-attach the dome bubble.
Figure A. B85, Dimensions
Figure B.
B85 mounting diagram.
Diameter
5 15/16”
(150 mm)
Height
1 3/4”
(44 mm)
Cable
retention
clip
RP1. 3/4” waterproof
rubber plug
Rubber
gasket
3
12
Up
Lens Direction
GUIDE PATTERN
4
Waterproof
RJ45
connector
Round head
machine screws
(provided)
3/4” side conduit
hole with metal plug
/
