Energy Suspension Spare Tire Bumper Pair Installation guide

Brand
Energy Suspension
Model
Spare Tire Bumper Pair
Type
Installation guide

Energy Suspension Spare Tire Bumper Pair is designed to isolate vibration and noise caused by your spare tire. Made from durable polyurethane, this bumper is easy to install and requires no drilling or modification to your vehicle. Simply remove your old bumper, trim the new bumper to the desired length, and snap it into place. The bumper will help to keep your spare tire secure and prevent it from rattling around while you're driving.

Energy Suspension Spare Tire Bumper Pair is designed to isolate vibration and noise caused by your spare tire. Made from durable polyurethane, this bumper is easy to install and requires no drilling or modification to your vehicle. Simply remove your old bumper, trim the new bumper to the desired length, and snap it into place. The bumper will help to keep your spare tire secure and prevent it from rattling around while you're driving.

1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
2015 Energy Suspension. All rights reserved.
C
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this type of work.
Energy Suspension recommends that you thoroughly read over all the installation instructions and check all P/N's and quantities in the Parts
List before you start. Call customer service at 949-361-3935 if the parts in your kit do not match this Parts List.
Installation Instructions
For Set # 2.9105
Rear Tailgate Tire Bumper
2007+ Jeep JK (all models)
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 8/JAN/03 BRH Updated 23/JAN/04 BRH
Updated 14/JAN/05 BRH Updated 10/JAN/06 BRH
Updated 2/JAN/07 BRH
2015 Energy Suspension. All rights reserved.
C
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
17P17666
16/DEC/15 MAX ECN 15131
OPEN FIRST!
Tailgate Tire Bumper Removal/Installation:
1. Loosen lug nuts and remove spare tire/wheel
from rear of vehicle
2. Remove OE tailgate tire bumper by firmly
grasping and pulling out at an angle
3. Trim your new polyurethane tire bumper to the
desired length using a hack saw or razor blade.
Polyurethane is difficult to cut so BE CAREFUL!
When trimming, be sure that the tire bumper is
long enough to contact the spare tire with approx.
1/4” of engagement for optimal vibration isolation
4. Install the new polyurethane tire bumper by
firmly pressing the small nub into the oval hole on
your tailgate. The bumper will snap in place when
fully installed
5. Reinstall your spare tire/wheel and torque lug
nuts to factory specs
Parts list:
2 - 06P06369
(Tailgate Tire Bumper)
1 - 17P17666
(This Instruction Sheet)
06P06369
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
2015 Energy Suspension. All rights reserved.
C
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this type of work.
Energy Suspension recommends that you thoroughly read over all the installation instructions and check all P/N's and quantities in the Parts
List before you start. Call customer service at 949-361-3935 if the parts in your kit do not match this Parts List.
Installation Instructions
For Set # 2.9105
Rear Tailgate Tire Bumper
2007+ Jeep JK (all models)
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 8/JAN/03 BRH Updated 23/JAN/04 BRH
Updated 14/JAN/05 BRH Updated 10/JAN/06 BRH
Updated 2/JAN/07 BRH
2015 Energy Suspension. All rights reserved.
C
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
17P17666
16/DEC/15 MAX ECN 15131
OPEN FIRST!
Tailgate Tire Bumper Removal/Installation:
1. Loosen lug nuts and remove spare tire/wheel
from rear of vehicle
2. Remove OE tailgate tire bumper by firmly
grasping and pulling out at an angle
3. Trim your new polyurethane tire bumper to the
desired length using a hack saw or razor blade.
Polyurethane is difficult to cut so BE CAREFUL!
When trimming, be sure that the tire bumper is
long enough to contact the spare tire with approx.
1/4” of engagement for optimal vibration isolation
4. Install the new polyurethane tire bumper by
firmly pressing the small nub into the oval hole on
your tailgate. The bumper will snap in place when
fully installed
5. Reinstall your spare tire/wheel and torque lug
nuts to factory specs
Parts list:
2 - 06P06369
(Tailgate Tire Bumper)
1 - 17P17666
(This Instruction Sheet)
06P06369
  • Page 1 1

Energy Suspension Spare Tire Bumper Pair Installation guide

Brand
Energy Suspension
Model
Spare Tire Bumper Pair
Type
Installation guide

Energy Suspension Spare Tire Bumper Pair is designed to isolate vibration and noise caused by your spare tire. Made from durable polyurethane, this bumper is easy to install and requires no drilling or modification to your vehicle. Simply remove your old bumper, trim the new bumper to the desired length, and snap it into place. The bumper will help to keep your spare tire secure and prevent it from rattling around while you're driving.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents