meitav-tec PS-2500-3S-FC-Super Product information

Brand
meitav-tec
Model
PS-2500-3S-FC-Super
Type
Product information
Date:
Title:
File name: PS2500-3S-FC-SUPER.VSD
Print name:Drawn: M.Ruchansky
Checked: O.Volovitch
Approved: E.Roy
PS2500-3S-FC-SUPER
15.03.07
PS-2500
X2 X1 16 15 14 13 12 11
0
F1
0
PR
0
F3
F4
0
F5
0
F6
Indoor Fan
(230Vac,3A)
0 Y 1 2 3 8 7 0 B A1
2
3
8
7
ETN/X500 ; FMH/X500 ; IRP/X500
Thermostat (Option)
~
N
GND
0
T3
0
T2
0
T1
P1
P2
P3
+12V
-12V
IR
230Vac
Change Over Sensor
Return Air Sensor
(See the operating
manual - #4)
Not in use
CONTROLLER
POWER
SUPPLY
+- Fuse
8A
JP5
JP4
0
F2
Not in use
Not in use
Occupancy
Sensor
12Vdc
RS485
On/Off Mode Fan
BACNET (Alerton) MSTP
Protocol
RS485
BACNET (Alerton) MSTP
Protocol
Indoor Coil Sensor
ID2014
F5 – Short – Fan Only mode available
(Selectable through thermostat)
F5 – Open – Fan Only mode not available
Indoor Coil Sensor (T3) Indoor Fan in heat mode
Auto Fan = ON :
With Indoor Coil Sensor
T3 > 32ºC → Fan ON
T3 < 28ºC → Fan OFF
Without Indoor Coil Sensor
The Indoor Fan will operate when there is a demand for
heating (with 30 seconds time delay)
Heat – Connector 14
For Valve only ! Do not connect an electrical heater !
Jumpers – JP4 & JP5
JP4 – SHORT (4-Pipe System)
Auto change over active
2 separate outputs for Cool and Heat (14 & 15)
T2 – for monitoring only
JP4 – OPEN (2-Pipe System)
Auto change over not active
1 output for Cool and Heat (15)
T2 – Logic selection
JP5 - SHORT
In Cool mode – Auto Fan
In Heat mode – Auto Fan
JP5 - OPEN
In Cool mode – Fan ON
In Heat mode – Fan ON
Occupancy Sensor
When the IR (N.C.) input is open
for 10 minutes, all outputs turn Off.
Short the (-12V) and (IR)
connectors, only when an
occupancy sensor is not connected
Change Over Sensor (T2) in 2-Pipe system:
With Change Over Sensor
T2 < 20ºC → Cool
T2 > 30ºC → Heat
Without Change Over Sensor
Manually select the mode using the wall panel or computer.
0
F4 – Fault input (N.C.)
When open – all outputs OFF (no delay)
F6 – Fault 2 input (N.C.)
Only for indication through the protocol
Pump Output –
230Vac , 1A
Will be active only
when the Cool output
is also active
Not in use
(Temperature through
the protocol)
JP1
JP1
End of Network jumper
– Jumper Short
(Resistance 120 Ω)
JP1 JP1
Open Short
Device Instance
Number ( DIN)
F1,0 F2,0
Unshort Unshort
Short Unshort
Unshort Short
F3,0 DIN
EEPROM
Unshort DIN=
MAC+1200
Unshort
Short Short Unshort DIN=
MAC+800
Unshort
Unshort Unshort
Short Unshort
Unshort Short
DIN=
MAC+600
Short DIN=
MAC+400
Short DIN=
MAC+200
Short Short Short DIN=MAC
Short
Device Instance
Number ( DIN)
DIN=
MAC+1000
MAC Phisical address of Device
(DIP SWITCH)
0,PR -Open thermostat
work in ºC.(Default from
factory)
0,PR -Close thermostat
work in ºF.
meitav-tec
Tel: +972-3-9636462
Fax: +972-3-9626620
e-mail: support@meitavtec.com
Important !
Disconnect power to the main board
before making any changes to DIP
switches/Jumpers, wiring the unit
and/or connecting the wall panel.
Shielded cable - Connect the
shield to the “8” terminal of
the main board.
5x0.5 12VDC
  • Page 1 1

meitav-tec PS-2500-3S-FC-Super Product information

Brand
meitav-tec
Model
PS-2500-3S-FC-Super
Type
Product information
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents