Midmark Procenter Systems Installation guide

Brand: Midmark

Model: Procenter Systems

Type: Installation guide

Midmark Procenter Systems offer flexible workstation solutions for dental operatories, providing healthcare professionals with enhanced reach, adjustability, and ergonomic benefits. These systems feature articulating arm designs that allow for precise positioning of instruments and tools, promoting improved access to the patient's oral cavity. They optimize workflow efficiency by integrating various dental tools and utilities, such as air/water syringes, handpieces, and suction, within easy reach of the dental team.

1© Midmark Corporation 2004

WARNING

DA150401i

003-1414-00 Rev. (L)

Flex Work Station Delivery Units

Installation Guide

Special Tools

Level

1/4" Deep Well Socket

3/8" Masonary Bit

9/32" Wood Bit

Hammer Drill

NOTE:

Remove any packaging from the

skid and the floor or wall mount

bracket, whichever applies to the

installation.

NOTE:

On systems that have the Flex Work Station

Column, Column must be in place before

mounting Delivery Unit.

Step 3: Lift up Upper Flex Arm

Cover and remove

four shipping screws

and washers.

Step 2: Move skid with unit toward

mounting bracket, aligning

bracket with bearing mount.

Step 1: Install mounting

bracket (floor or wall).

Refer to appropriate

installation.

WARNING

Do NOT remove the Heavy Cable

Tie until the Flex Delivery Unit is

securely mounted in place on the floor or

wall bracket.

Failure to comply could result in serious

injury and / or equipment damage.

Step 4: Supporting unit to

prevent tipping, slide

unit forward (toward

mounting bracket) on

rails.

NOTE:

The bearing mount

can be moved up or

down to align mounting

holes.

Cable

Tie

Electrical Requirements: 24VAC, 3.2 amp

13VAC, 2.0 amp

Style A

DA150901i

SECURING FLEX ARM

NOTE:

Assure the floor is of such constructions that the unit will be

adequately supported and anchored.

Use appropriate hardware to anchor the floor mount to the floor.

Floor

Mount Bracket

Floor

Mount Bracket

Non-Concrete

9/32 "

Diameter

3/8 "

Diameter

Concrete

(5.08 cm)

Anchor Wedge

(3/8" x 3-1/2")

Lag Bolt

(3/8" x 2-1/2")

NOTE:

Once the flex unit is secured to the

mounting plate the heavy cable tie

can be removed.

Press down on the work station

while cutting the cable tie then

carefully release the work station.

Step 1: First install mounting

screw and washer at

top, left

position.

Step 2: Install eccentric and

screw in

bottom, left

position.

Step 3: Install remaining

two mounting

screws.

Eccentric

3© Midmark Corporation 2004

DA151601i

Equipment Alert

Mounting structure must be

capable of supporting:

Weight (Max.) .... 120 lbs. (54.4 kgs)

Torque (Max.) .... 170.8 ft-lbs. (231.5 N•M)

Mounting plate must

not deflect more

than 1/16" (1.6 mm) over a 12" (30.5 cm)

distance.

WALL MOUNT

NOTE:

Install and level the Flex Work

Station Wall Mount Delivery Unit

using the same procedures as used

on the Floor Mount installation.

Step 3: Install mounting

cover using

4 #10-32 x 3/8"

screws.

Step 3: Remove

cap plug.

Tension

Adjustment

Step 1: Place lower flex arm cover

in position and secure with

four #10-24 x 3/8" self-

tapping screws.

Step 2: Install the

bracket, two

#10-24 x 3/8"

screws.

Step 5: Using a 7/16"

socket, adjust

Flex Arm tension.

Master

ON / OFF

Step 4: Place Master switch

to the ON position.

Equipment Alert

Use care not to back

bolt all the way out

when adjusting flex tension.

FLEX TENSION ADJUSTMENT

NOTE:

Perform final adjustments after installation

of operatory is complete.

Place a load on the work station similar to

what it will be exposed to by the assistant’s

or doctor’s instruments

2 1/2"

(6.4 cm)

from Floor

Step 2: Secure frame

to wall with 8

(5/16"x 2 1/2")

lag screws.

Step 1: • Locate wall studs.

• Align 8 holes in mounting

plate with studs so

bottom of plate

is 2 1/2"

(6.4 cm) from floor.

• Mark and drill pilot holes

(Use 1/4" drill bit).

16" (40.6 cm)

on Center

DA151100i

DA151000i

LEVELING WORK STATION

LEVELING FLEX ARM

Step 1: • Loosen set screw

• Turn eccentric nut to level

side to side.

• Hold eccentric nut from

moving while tightening

set screw.

Step 3: Tighten mounting

bolts to hold level

position.

Step 2: Turn set screws

inward or outward

for front to back level.

NOTE:

When leveling, position work surface

to right of cabinet front for a right-

hand doctor, and to left for a left-

hand doctor.

Step 1: Work Station must

be leveled side to

side and front to back.

Step 3: Turn set screws

inward or outward

to achieve level.

Step 2: Loosen mounting

screws.

Step 4: Tighten mounting

screws to maintain

setting.

5© Midmark Corporation 2004

DA152000i

DA151200i

WORK SURFACE ONLY

INSTALLATION

NOTE:

Level the Work Surface using the

same procedures as leveling the

Work Station.

Step 3: Secure tubing to cable

bracket with cable tie.

Step 2: Install Flex Lock Switch

assembly using two

#10 x 5/8 " particle

board screws.

Step 1: Position Work Surface

in place and secure

with four screws.

Master

ON / OFF

Brake

Switch

Step 1: Place Master switch

to the ON position.

Flex

Tension

Brake

Adjustment

Pivot

Adjustment

FLEX ARM ADJUSTMENTS

NOTE:

Refer to Flex Tension Adjustment

for procedures on adjusting the

tension on the Flex Arm.

Step 2: Position Brake Switch

so the brake is LOCKED.

NOTE:

Work Station should

retain position when

Brake is LOCKED.

Step 3: Using 1/8" allen wrench,

adjust brake.

Clockwise......Tightens Brake

C’Clockwise...Loosens Brake

Step 4: Adjust amount of

drag at all pivots by

turning set screws.

Step 5: After completing

adjustments install

cover.

Step 4

TUBING CONNECTIONS.

80-100

PSI

30 PSI Filtered City Water

80-100

PSI

80-100 PSI

Filter / Regulated Air

80 PSI

1/8

Red

DA150001i

To Handpiece Drive Air

(5/16" Clear)

1/8 Purple

1/8 Yellow

1/8 Brown

1/8

Purple

1/8

Brown

1/8 Red

PSI

1/8 Orange

To Handpiece Coolant Air (1/8 Green)

Clear

Throttle

Valve

Wet / Dry

Toggle

30 PSI

1/8

Yellow

Unfiltered / Unregulated Air

1/8 Red

To Pilot Air for Coolant Water (1/8 Orange)

1/8 Green

Air

Regulator

Air from Master

On / Off Switch

Air to Master

On / Off Switch

1/8

Red

FWC Air / Water Supply

(located in cabinet base)

Manual

Shutoff

Valve

(Air)

Master

Pilot

Shutoff

Manual

Shutoff

Valve

(Water)

Master

Pilot

Shutoff

City Water to

Water Selector

Valve

Air to

Water Bottle

Air to Syringe

Filter / Regulated Air

003-1433-00 Rev. B

Water

Regulator

80 PSI

PSI

Transformer

Air Pressure

Switch

(Optional)

N/O

N/C

Supply

Air

80-100

PSI

Foot Control

1/8

Red

City

Supply Water

30-50 PSI

80-100 PSI

80-100

PSI

Master Pilot Shutoff Valve

Clear

Vacuum

5/8

Vacuum Supply Tube

30 PSI

1/8

Blue

80 PSI

Air

Regulator

1/8 Orange

1/8 Green

5/16"

Clear

1/8 OR

1/8

5/16"

Clear

w/ Dash

1/8

(Chip Air)

Chip Air (Brown)

not used on 12:00

FSC applications

5/16" Clear

(w/Black Dash)

5/16" Clear

ELECTRICAL CONNECTIONS.

DA168401i

J13

J11

J10

CL 1/8"

CL 1/4"

L-1

N-2

Ground

YL / GN

Chair

PCB

Connect

to J2

Chair PCB

Harness

To Accessory Plug

0 - 12 or 24 VAC for

Electric Handpiece,

Camera, Scaler,

Heated Syringe, etc.

Extension

Harness

To 120 VAC

Supply

Chair Control

Harness

Spare Low Voltage

Supply to Other

Accessories

Low Voltage

to Optional

Handpiece

Illumination

Transformer

Connect to

Extension

Harness

Vacuum

Handpiece

Drive Air

Spare

Air to

Water

Bottle

Air to

Syringe

Air to

Master

On / Off

Switch

Air to

Handpiece

Coolant

Valve

Pilot Air

for Coolant

Water

Spare

City Water

to Selector

Switch

Air from

Master

On / Off

Switch

Umbilical from

Flex Work Station

Legend

Wire & Tubing Designations

RD Red

WH White

GN Green

YL Yellow

BK Black

BL Blue

OR Orange

BR Brown

CL Clear

Vl Violet

(Purple)

YL / GN Yellow / Green

Midmark Corporation

60 Vista Drive

P.O. Box 286

Versailles, OH 45380-0286

937-526-3662

Fax 937-526-5542

www.midmark.com

TUBING CONNECTORS

When connecting internal tubing to metal barbed fittings

during installation, it is necessary to use the plastic

retainers included with operatory components.

NOTE:

For 1/8" tubing use Uni-Clamps

For 1/4" tubing use Sleeves

KA930702

Uni-Clamp

Barbed Fitting

1/8"

Tubing

1/8" Tubing

Sleeve

Barbed Fitting

1/4"

Tubing

1/4" Tubing

RECOMMENDED PRESSURE SETTINGS

• City Water Regulator Valve ............ 30 PSI

(2.1k/c

)

• Air Regulator Valve ........................ 80 PSI

(5.6 k/c

)

• Water Bottle Regulator Valve ......... 30 PSI

(2.1k/c

)

WEIGHT LIMITATIONS

Maximum Load

(On work surface) ...........................

40 lbs. (18.1 kg)

Midmark Procenter Systems Installation guide

Midmark Procenter Systems Installation guide

Midmark Procenter Systems Installation guide

Related papers

Other documents