Howdens Joinery HCB1721 Operating instructions

Brand: Howdens Joinery

Model: HCB1721

Type: Operating instructions

Standard drawer box pack

Section 4 - Kitchen installation - Drawer packs

Standard drawer box pack

Assembly Standard pan drawer box illustrated,

standard drawer box similar.

Pan drawer box

Drawer box

13mm Flange

head screw x6

2.5mm

5mm

deep

Support rail sleeve x2

413mm CSK screw x4

Back panel

standard or pan

Drawer

bottom

RH drawer side

RH runner

LH drawer side

LH runner

Drawer front,

see next page

for spike hole

dimensions

Support rail

1Front fixing x2

Rear fixing x2

CSK screw x6 2

2.5mm

5mm

deep

13mm Flange

head screw

Standard drawer box pack Standard drawer box pack

Section 4 - Kitchen installation - Drawer packs

160mm

(standard

drawer box)

25mm 25mm

107mm

43mm

227mm

(standard

drawer box)

25mm 25mm

107mm

43mm

390mm

(pan drawer box)

Bottom edge

25mm 25mm

114mm

235mm

50mm

230mm

356mm

(standard

drawer box)

25mm 25mm

107mm

43mm

Bottom edge

Pan drawer only

For the assembly and fitting of the chosen drawer type, please refer to the assembly

sheets supplied with the drawer pack.

NOTE: Instruction shown in this section is for the standard drawer adjustment only. For

further types please refer to the assembly sheet supplied with the drawer pack.

Although drawer adjustment should not be necessary, if required follow instructions

below.

If when assembled the drawer fronts are not equally spaced and aligned, they will

need to be adjusted. This is done by moving the front of the drawer runner up or down

on either or both sides of the cabinet as follows:

a) Bradawl in the centre of the front slotted hole ‘B’ and fix with a 12mm shallow head

CSK screw (where supplied) or 13mm CSK screw.

b) Take out front screw ‘A’.

c) Try the drawer, adjusting the runner up or down until the drawer front correctly

aligns.

d) Finally bradawl and fix a 12mm shallow head CSK screw (where supplied) or 13mm

CSK screw into locking position ‘C’. Secure screw ‘B’.

Drawer fronts

Runner adjustment Drawer adjustment

600 3 Drawer

114mm

669mm

507mm

344mm

29mm

400 4 Drawer 500 4 Drawer

669mm

507mm

121mm

29mm

300 3 Drawer300 2 Drawer Drawer-line

application

500 2 Drawer 600 2 Drawer

474mm

114mm

Drawer runner installation

Standard drawer box pack - HL cabinet application Standard 700/800/900/1000 drawer box

Section 4 - Kitchen installation - Drawer packs Section 4 - Kitchen installation - Drawer packs

Drawer fronts and side panel

800/1000 Drawer application

Drawerbox

13mm CSK

screws

669mm

*29mm

381mm

*27mm when spiking

on centre upright.

8mm

13mm CSK

screws

If you are installing an internal drawer in a standard

drawer application, follow the dimensions below.

29mm

464mm

114mm

160mm

(standard

drawer box)

25mm 25mm

107mm

43mm

Bottom edge

220mm

356mm

(standard

drawer box)

25mm 25mm

97mm

33mm

Bottom edge

Standard drawer box pack - HL cabinet application Standard 700/800/900/1000 drawer box

Section 4 - Kitchen installation - Drawer packs

Front ﬁxing x2

Rear ﬁxing x2

CSK screw x6

13mm Flange head

screw x4

2.5mm

5mm

deep

Drawer base

Drawer back

Drawer

back

Drawer

back

Drawer

front

Drawer support

rail

Drawer front

Drawer side

(LH/RH)

13mm Flange head screw x6

2.5mm

5mm

deep

Runner (LH/RH)

Drawer box (160mm) Pan drawer box (275mm and 356mm)

In order to maximise the efﬁciency in the loading capability of the drawer box, a drawer reinforcement

catch (supplied) must be ﬁtted as shown in this assembly leaﬂet. The catch will ensure that the drawer

can be loaded to its full capacity whilst keeping the optimum functionality in opening and closing.

Drawer support rail x2

13mm CSK screw x4

Upgrade drawer box pack - Soft close and non-soft close

Standard 700/800/900/1000 drawer box

Section 4 - Kitchen installation - Drawer packs

Drawer fronts - 2 drawer application Drawer fronts - 3 drawer application

356mm

25mm

230mm

107mm

43mm Bottom edge

160mm

25mm

107mm

43mm

Bottom edge

275mm

25mm

107mm

230mm

43mm

Bottom edge

NOTE: Only the spike positions to be used on the drawer fronts

are shown for extra clarity

Drawer runner installation

700/800 2 Drawer

25mm

900/1000 3 Drawer

114mm

669mm

392mm

29mm

381mm

29mm

474mm

114mm

381mm

Runner reinforcement catch

and adjustment

Fit the runner reinforcement catch to the cabinet above the runner in

the position shown. Secure using the 13mm CSK screws.

Drawer adjustment

Pan drawer only

Although drawer adjustment should not be necessary, if required follow

instructions below. If no adjustment is required, proceed to step d.

If when assembled the drawer fronts are not equally spaced and aligned,

they will need to be adjusted. This is done by moving the front of the drawer

runner up or down on either or both sides of the cabinet as follows:

a) Bradawl in the centre of the front slotted hole ‘B’ and ﬁx with a

13mm CSK screw. Do not fully tighten.

b) Take out front screw ‘A’.

c) Try the drawer, adjusting the runner up or down until the drawer front

correctly aligns. Secure screw ‘B’.

d) Finally bradawl and ﬁx a 13mm CSK screw into locking position ‘C’.

Upgrade drawer box pack - Soft close and non-soft close

Section 4 - Kitchen installation - Drawer packs

Standard 700/800/900/1000 drawer box

Assembly Generic pan drawer box illustrated, drawer box,

300, 500, 800, 900 and 1000 pan drawer box similar.

Drawer box 500

Pan drawer box

300/800/900/1000

Pan drawer box

NOTE: Drawer box back panels will vary in

height depending on the drawer box chosen.

IMPORTANT:

When fitting the drawer base

to the drawer box the base

MUST be aligned to the front

of the drawer sides, so it sits

flush with the back of the

frontal once fitted.

Scan QR code above

for more details.

Drawer front,

see next page

for spike hole

dimensions

Back panel

drawer, 800, 900

and 1000 pan

drawer

Drawer

bottom

RH drawer

side

LH drawer

side

Support rail

4 4

2.5mm

5mm

deep

2.5mm

5mm

deep

413mm Flange head screw x9

Fixing tube x2

13mm Flange

head screw x2

Front fixing x2

16mm Flange

head screw x4

800, 900 and 1000 Pan

drawer box.

90° die cast bracket

13mm Flange head

screw x2

Scan the QR code with your

smart device, to access a

short installation video.

Upgrade drawer box pack - Soft close and non-soft close

Section 4 - Kitchen installation - Drawer packs

Upgrade drawer box pack - Non-soft close

73mm

599mm

437mm

274mm

27mm

59mm

599mm

342mm

599mm

437mm

105mm

27mm

599mm

337mm

59mm

900

3 Drawer

300

3 Drawer

1000

3 Drawer

Drawer-line

Application

500

2 Drawer

450

2 Drawer

600

2 Drawer

700

2 Drawer

1000

2 Drawer

800

2 Drawer

400

2 Drawer

350

2 Drawer

300

2 Drawer

600

3 Drawer

400

4 Drawer

500

4 Drawer

1000

4 Drawer

418mm

59mm

418mm

59mm

Drawer runner installation - Soft close upgrade

32mm 32mm

116mm

84mm

227mm

(drawer box)

Bottom edge

160mm

(drawer box)

32mm 32mm

87mm

Bottom edge

55mm

Top / Bottom drawer

32mm

102mm

230mm

198mm

70mm

356mm

297mm, 347mm, 397mm, 447mm, 497mm,

597mm, 797mm, 1000 (pan drawer)

497mm, 597mm, 897mm, 997mm

Bottom edge

900 / 1000 Drawer

32mm

102mm

230mm

198mm

70mm

275mm

897mm, 997mm (pan drawer)

Bottom edge

390mm

(pan drawer box)

437mm

(used in appliance

tower applications)

32mm 32mm

243mm

275mm

115mm

147mm

Bottom edge

LH/RH runner x1 (pair)

8 x 13mm or 18mm (where

supplied) CSK screws

Drawer fronts - Soft close

Upgrade drawer box pack - Soft close and non-soft close Upgrade drawer box pack - Non-soft close

Section 4 - Kitchen installation - Drawer packs

27mm27mm

599mm

337mm

59mm

900 3 Drawer 1000 3 Drawer

800 2 Drawer

418mm

59mm

4 x 4.5mm x18 CSK screw

Drawer runner installation - Non-soft close

32mm 32mm

87mm

Bottom edge

55mm

32mm

102mm

198mm198mm

230mm

70mm

356mm

797mm

Bottom edge

32mm

102mm

230mm

70mm

275mm

160mm

897mm, 997mm

997mm

Bottom edge

Drawer fronts - Non-soft close

NOTE: The soft close adaptor kit is not compatible with the upgrade drawer kit.

Upgrade drawer box pack - Soft close Upgrade drawer box pack - Stabiliser kit

Section 4 - Kitchen installation - Drawer packs Section 4 - Kitchen installation - Drawer packs

Drawer adjustment

Drawer front removal

Pan drawer only

1 2

3 4

Once drawer front is adjusted

install cover cap.

Upgrade drawer box pack - Soft close Upgrade drawer box pack - Stabiliser kit

Section 4 - Kitchen installation - Drawer packs

‘X’ –86mm (minus)

‘X’ –86mm

(minus)

IMPORTANT NOTES:

This covers the drawer stabiliser kit, generic installation instructions

Fit the LH and RH stabiliser brackets, (indicated LH and RH on stabiliser brackets viewed from the front).

Cut the connecting rod to length.

Fit the stabiliser tracks to the cabinet.

The stabiliser tracks are marked LH and RH, (viewed from the front).

Positioning of the stabiliser tracks are dependant up on drawer depth and conﬁguration.

Fit the rod to the stabiliser brackets using the adaptors.

107mm (pan drawer)

171mm (deep pan drawer)

20mm minimum clearance

Upgrade drawer box pack - Soft close

Section 4 - Kitchen installation - Drawer packs

Internal drawers

800/900/1000 Drawer-line

8 x 30

Wooden dowel

Support rail

RH Runner

13mm CSK

screw x4

Not applicable for 1000 3 drawer cabinet.

5mm

8 x 30 Wooden dowel x2

45mm or 50mm CSK screw x1

40mm CSK screw x2

Front rail

Additional worktop

fixing screws.

8mm

Upgrade drawer box pack - Soft close

Section 4 - Kitchen installation - Drawer packs

Internal drawers

Shallow drawer box

Deep drawer box Assemble drawer box back and sides. Fit base and secure with screws.

Assemble drawer box back and sides. Fit base and secure with screws.

Push ﬁt front onto drawer sides. Screw ﬁt rails into position.

Remove one end cap from the drawer

front by removing screws and ﬁt handle.

Replace end cap once ﬁtted.

Fit drawer front.

Cover caps

IMPORTANT NOTES:

This covers the drawer assembly, installation and

application examples for deep and shallow drawers

Assembly

3 4

1 2

3 4

Section 4 - Kitchen installation - Drawer packs

Internal drawers Internal drawer towers

Installation and application

Deep drawer spacing Shallow drawer spacing

IMPORTANT: When using a shallow drawer above two pan drawers, follow the diagram for shallow drawer runner positioning (see below).

*IMPORTANT: Internal drawer being positioned lower for induction hob applications. 89mm dimension can be 125mm with

418mm dimension being 408mm if more room is required above in induction hob/thin worktop applications.

Application examples

Drawers can be ﬁtted in multiple combinations in the 600mm base units. Shown below are just some of the combinations which can be ﬁtted.

NOTE: Drawers will need to be ﬁtted around hinge positions.

Screws

(18mm CSK)

28mm

225mm

(Minimum spacing

required)

104mm

(Minimum spacing

required)

28mm

HL - STD DRAWER

149mm

277mm

405mm

533mm

HL - DEEP DRAWER

149mm

411mm

DL - STD DRAWER

149mm

259mm

369mm

DL - DEEP DRAWER

NOTE: Drawers are only suitable for use in cabinets when used in

conjunction with 155° hinges

147mm

372mm

27mm

33mm

Top pan

drawer runner

353mm

*418mm

59mm

*89mm

631mm

418mm

105mm

27mm

32mm for internal drawer runners

32mm 32mm

243mm

115mm

147mm

Bottom edge

FH Door

Internal three drawer

Section 4 - Kitchen installation - Drawer packs

Internal drawers

Section 4 - Kitchen installation - Drawer packs

Internal drawer towers

500 Standard and Tall

Internal Larder Tower

600 Standard and Tall

Internal Larder Tower

Speciﬁc internal drawer sales options (5 Drawer)

Follow the information below for how to create speciﬁc internal drawer larder tower conﬁgurations.

NOTE: Other combinations can be achieved by moving and adding drawer options.

500 Std and Tall* Tower Option 1

32mm

352mm

161mm

395mm

883mm

1108mm

1400mm

500 Std and Tall* Tower Option 2

32mm

352mm

161mm

710mm

883mm

1108mm

395mm

*Tall tower sales options will be supplied with the 180mm top box and increased size top door.

Drawer conﬁgurations remain in the same positions.

Internal drawer towers - other applications

Section 4 - Kitchen installation - Drawer packs

Internal drawer towers

600 Std and Tall* Tower Option 1

*Tall tower sales options will be supplied with the 180mm top box and increased size top door.

Drawer conﬁgurations remain in the same positions.

32mm

352mm

161mm

395mm

883mm

1108mm

1325mm

600 Std and Tall* Tower Option 2

32mm

395mm

710mm

883mm

1325mm

Section 4 - Kitchen installation - Drawer packs

Internal drawer towers - other applications

Section 4 - Kitchen installation - Drawer packs

Internal drawer towers

Application examples

Drawers can be ﬁtted in multiple combinations in the 600mm appliance tower units.

Shown below and on the following page are just some of the combinations which can be ﬁtted to the tower units.

NOTE: Drawers will need to be ﬁtted around hinge positions.

Installation and application

50/50 APPLIANCE TOWER - STD DRAWER 50/50 APPLIANCE TOWER - DEEP DRAWER

ONLY WHEN NO MIDDLE SHELF FITTED

149mm

253mm

357mm

461mm

565mm

914mm

1154mm

1258mm

1466mm

ONLY WHEN NO MIDDLE SHELF FITTED

149mm

374mm

599mm

914mm

1154mm

1379mm

NOTE: Drawers are only suitable for use in cabinets when used in

conjunction with 155° hinges

Deep drawer only

Once drawer front is

adjusted install cover cap.

See following page for 70/30 tower applications.

Adjustment

Section 4 - Kitchen installation - Drawer packs

Internal drawer towers - other applications Shallow drawer box

70/30 APPLIANCE TOWER - STD DRAWER

Right hand door opening

70/30 APPLIANCE TOWER - DEEP DRAWER

Right hand door opening

ONLY WHEN NO MIDDLE SHELF FITTED

149mm

253mm

357mm

461mm

696mm

868mm

972mm

1076mm

1314mm

1418mm

ONLY WHEN NO MIDDLE SHELF FITTED

149mm

374mm

696mm

868mm

1093mm

1314mm

70/30 APPLIANCE TOWER - STD DRAWER

Left hand door opening

70/30 APPLIANCE TOWER - DEEP DRAWER

Left hand door opening

ONLY WHEN NO MIDDLE SHELF FITTED

149mm

253mm

357mm

461mm

696mm

868mm

972mm

1471mm

ONLY WHEN NO MIDDLE SHELF FITTED

149mm

374mm

696mm

868mm

1471mm

1093mm

1076mm

1180mm

1284mm

Installation and application NOTE: Drawers are only suitable for use in cabinets when used in

conjunction with 155° hinges

Section 4 - Kitchen installation - Drawer packs

Internal drawer towers - other applications

Section 4 - Kitchen installation - Drawer packs

Shallow drawer box

IMPORTANT: ALL DIMENSIONS ARE TAKEN

FROM THE BOTTOM EDGE OF THE UNIT

300 3 Drawer 600 3 Drawer 500 4 Drawer

Assembly

73mm

599mm

437mm

274mm

599mm

437mm

105mm

27mm 27mm

600 2 Drawer500 2 Drawer 400 4 Drawer

418mm

59mm

27mm

Pan drawer front

(300mm & 600mm Only)

spike positions

Bottom edge

243mm

275mm

147mm

115mm

390mm

To ﬁt the shallow drawer runners and feet to the cabinet,

follow the ﬁxing details shown below.

Front

Cabinet

base panel

92.5mm

40mm40mm

217.5mm

Section 4 - Kitchen installation - Drawer packs

Push to open drawers Push to open drawers

Assembly NOTE: Do not ﬁt the drawer front at this stage.

Runner loading weight and mechanism type information can be found on the

components in the locations shown below

Runner Mechanism

Fit the mechanisms to the drawer

box both sides.

Ensure the cabinets are square, level and secured to the wall before ﬁtting drawer boxes.

Drawer boxes must also be square to ensure correct operation of the push to open mechanism.

Fit the latch to the drawer runners

both sides.

Fit the drawer front to the drawer box and ﬁt the

central support bracket (700, 800, 900 &

1000 drawers) to the front of the base panel

and back of the drawer front.

Cabinet

Drawer box

Click into position

Runner latch

(LH & RH) x1 pair

Flush

NOTE: Ensure the front of the

drawer base is ﬂush with the

front of the drawer box.

Click into

position.

Drawer box mechanism

(LH & RH) x1 pair

Runner/

MechanismDrawer size Max loading*

300 std & 300 Pan

350/400/500/600 std

400 - 600 Pan

700 - 1000 std & Pan

30kgs/L1

30kgs/L3

50kgs/L5

20kgs

30kgs

50kgs

HYH4405

HYH4406

HYH4407

*inc. drawer

box & frontal

Section 4 - Kitchen installation - Drawer packs

Push to open drawers

Section 4 - Kitchen installation - Drawer packs

Push to open drawers

Fit the adaptors to each end of the synchronisation rod

(not applicable for 300mm drawers). Fit the rod by clipping

into both mechanisms.

NOTE: Rod design is different for the 300 drawer box

IMPORTANT: The synchronisation rod will

need to be cut (using a hacksaw) to the appropriate

length before ﬁtting. Follow the table for the

correct size for the application.

IMPORTANT: A minimum gap of 2.5mm between the

drawer front and the cabinet is required for correct

push to open operation. Use the adjustment wheel on

each mechanism and the adjustment tool (supplied

separately), making sure the gap is parallel and identical

on both sides of the drawer.

700, 800, 900 and 1000 Drawer Boxes

Fit the bracket to the centre of the drawer box

using the screws to secure.

NOTE: For 800 sink drawers, the bracket

is positioned the other side of the

synchronisation rod.

Adjustment

Push in, then release

for drawer to open.

Synchronisation rod x1

HYH4408

Adaptor x2

2.5mm minimum

(parallel and identical

on both sides).

–

Adjustment wheels

(on the underside of the drawer).

2.5mm 2.5mm

+ +

––

Adjustment tool

(supplied separately).

HYH4400

Drawer Size

1000mm

900mm

800mm

700mm

600mm

500mm

400mm

724mm

624mm

524mm

424mm

324mm

224mm

124mm

Bracket x1

3.5mm x 13mm

Flange Head Screws

32mm

22mm

32mm

Centre

line

104mm

Page is loading ...

Howdens Joinery HCB1721 Operating instructions

Howdens Joinery HCB1721 Operating instructions

Howdens Joinery HCB1721 Operating instructions

Related papers

Other documents