Howdens Joinery RKC1477 Operating instructions

Brand: Howdens Joinery

Model: RKC1477

Type: Operating instructions

226

Section 8 - Curved units

Curved corner post Curved base cabinet

Section 8 - Curved units

Measure and cut post and decor end dependent on cabinet application, making sure

allowance is made for any scribing to the wall requirements.

IMPORTANT: To reduce the risk of damage to cut edges due to moisture ingress

(where they are exposed to moisture) all raw edges must be sealed using a suitable

moisture resistant sealant, such as waterproof varnish or silicone.

Screws (32mm)

Screws x3/6 (32mm)

Screws x3 (25mm)

per ﬁxing block

Fixing block

Tower

Base

Tall wall

Wall

x3 Rails supplied (700mm in length)

for both post rail and back rail.

Cut and use rails appropriate to the

height of your post/decor end (see

diagrams below).

Secure post rail(s) into

place using PVA glue

Screws (55mm)

700mm

rails

700mm

rails

Door

700mm

rails

350mm

rails (cut)

700mm

rails

700mm

rails

350mm

rails

Assembly

‘X’ mm

NOTE: Dimension ‘X’ is dependent upon

door thickness. An additional 2mm

should be added onto the dimension of

the door to allow for door alignment.

For 16mm decor ends

use 2/3 metal brackets

to space the decor end

away from the the post/cabinet

Metal spacer

brackets for 16mm

decor ends

HKC0020

227

Section 8 - Curved units

Curved corner post Curved base cabinet

Section 8 - Curved units

1 to 2mm gap

Curved base soft-close hinge pack required

Fit the hinge and plate to the door

and decor panel.

16.5mm

Fit battens to the decor panel.

With the base cabinet laid ﬂat, secure the decor

panel and door using screws through the base

and top shelf and into the battens.

30mm CSK screw x6

Hinge and plate x2

13mm CSK screw x4

16.5mm

40mm CSK screw x4

1 to 2mm gap

21.5mm

For ﬁxing the legs to your cabinet, see page 22-23.

Assembly

228

Section 8 - Curved units

Curved wall cabinet Curved plinth - Joining

Section 8 - Curved units

Position the curved cabinet to the wall and secure through the back panel using suitable wall ﬁxing screws.

NOTE: Wall ﬁxings can be hidden behind the shelf positions as required.

Ensure the cabinet is ﬂush with the adjoining unit side and front edges.

NOTE: For curved deep wall cabinets,

use the cranked hinges supplied with cabinet

Standard wall cabinet Deep wall cabinet

IMPORTANT:

When tiling up to the curved wall

cabinet, ensure sufﬁcient gap is left

to enable the door to open correctly.

Secure through the adjoining unit

and into the curved wall.

30mm CSK screw

Suitable wall ﬁxing

screws

Installation

229

Section 8 - Curved units

Curved wall cabinet Curved plinth - Joining

Section 8 - Curved units

Align the curved plinth section to the side of the curved cabinet base and scribe

the end to the wall as required. Mark and ﬁt plinth clips to the back of the

plinth sections as shown.

IMPORTANT: To reduce the risk of damage to cut edges due to moisture ingress

(where they are exposed to moisture) all raw edges must be sealed using a suitable

moisture resistant sealant, such as waterproof varnish or silicone.

Corner post cap and cornice/pelmet ﬁxed in the same way.

Fit a metal plate to the back of

the plinths to secure the joint. Position the curved plinth assembly to

the cabinet run and clip onto the

cabinet leg sections.

Apply a two part adhesive to the adjoining

ends of the plinth sections and ﬁt together.

NOTE: Make sure sections are ﬂush.

Curved plinth section

Straight

plinth section

Adhesive

Assembly

2 3

Howdens Joinery RKC1477 Operating instructions

Howdens Joinery RKC1477 Operating instructions

Howdens Joinery RKC1477 Operating instructions

Related papers

Other documents