Bottom protection silicone
*(注：3D效果需求，具体以实物为准）
* (Note: 3D eect requirements, the actual object shall prevail)
CNC机头及摄像头侧板安装
CNC camera mount and camera side plate installation
多功能天线座安装
安装好单侧板与GPS座
选择适合的图传天线座
Choose a suitable VTX antenna base
Choose a suitable VTX antenna base
Install the plate on one side
and GPS base
Install the multi-function antenna base
SMA 天线座
SMA antenna base
M2.5*8
M2.5*8
(内六角半圆头自攻螺丝)
M3*23 网纹铝柱
O3 Air Unit 天线座
GPS 安装座
*(注：装配示意图，机架不包含天线）
安装好另一侧板
装入T型天线
Install the T-shaped antenna
(*Note: pictures for assembly reference only.
Frame doesn’t include antenna)
M3*23 stando
O3 Air Unit antenna base
Button head hex socket screw
GPS installation base
(Size:18*18*8mm)
Install the plate on the other side
M3*11
M2*8
M3*14 M3*14
后机臂
把飞塔减震模块安装到对应位置
*注:分前后机臂
前机臂x2 后机臂x2
机臂与减震安装
（依次完成4个机臂的安装）
同样方式安装好两侧的螺丝
Install arms and anti-vibration module
(Complete the installation of 4 arms in turn)
Install the anti-vibration stack
module to the corresponding position
Back arm
前机臂
Front arm
Install the screws on both sides
in the same way
把中板安装到对应的6个螺丝位
电容及蜂鸣器位置
上紧机臂相交位置的两个按压螺母
安装中板
Install the middle plate to the corresponding
6 screw positions
Tighten the two press-in nuts
where the arms intersect
Install middle plate
中板
middle plate
底板
bottom plate
*Notice: front and back arms
Back arm
Direction for drone head
Front arm
Place for capacitor and buzzer
底部保护硅胶
(0.5mm)
安装7075工型铝柱
M3*6
M2.5*6
M3*5
与完成的1、2两部分组合
机身与天线座组合
Combination of frame and CNC
camera mount
Frame and antenna base
combination
Combination with completed pas 1 and 2
机身与CNC机头组合
Install 7075 stando
1
1
2
2
3
2
同样方式安装好4个机臂
Install 4 arms in the same way
4
螺丝依次穿过底板及机臂相交位置
Screws pass through the bottom plate and
the intersection position of the arms in turn
1
1
1
2
2
34
RunCam LINK安装位置
机头方向
摄像头侧板
前顶板
M2*3
M3*5
Front top plate
Camera side plate
安装前顶板
Install the front top plate
天线安装顺序
Antenna Installation Sequence
先将O圈套入天线,
以便在TPU天线座上起到固定作用
inse the O-ring into the antenna to
secure it on the TPU antenna base.
电池防滑硅胶
后顶板
飞塔挡板
M3*6
M3*6
M3*6
M2*4
后顶板及电池防滑胶安装
最后装后顶板及电池防滑硅胶
Finally, install the rear top plate and
batte anti-slip silicone
Install rear top plate and batte anti-slip silicone
Batte anti-slip silicone (2.5mm)
Rear top plate
Stack protector
Capacitor
Buzzer
机臂保护脚架安装方式
5mm
*(注：标配螺丝为M3*8mm，M3*10mm）
把3D打印保护脚架安装到机臂上
按电机螺丝固定座的高度选择适合长度的螺丝
Install the 3D printed foot mount to arms
Arm foot mount installation
电调电源线焊接及电机线长推荐
ESC power cable soldering and
recommended length for cable of motor
Use screw of proper length based on the
motor installation
(*Notice: default screws are M3*8mm, M3*10mm)
M3*10
M3*8
O3 Air Unit 6P排线
Master 蜂巢形散热片
M1.6*8
O3 Air Unit 图传
需拆下O3 Air Unit 图传底部4颗原装螺丝
从图传顶部通过
O3 Air Unit 安装方式
O3 Air Unit Installation Method
O3 Air Unit VTX
The 4 original screws at the bottom of the O3 Air Unit need to be removed
O3 Air Unit 6P ex cable
Pass through the top of the VTX
Master honeycomb heat sink
建议电调选择水平180度反装
建议电调电源线长为100mm左右，实际请参考你所使用的电池。
*注 （电调反装后，切记重新定义1-4号电机的正确位置及转向。）
Recommend installing ESC in reverse horizontally 180°
*Note (After the ESC is installed reversely, remember to redene the correct position and
direction of motors 1-4.)
*注 （如机头安装TPU保护，需更换成
M3*6半圆头内六角螺丝）
*Notice: please change to M3*6 button head hex
socket screws if installing TPU protection at the
drone head pa.
It is recommended to keep the power cable of ESC to be about 100mm.
Please refer to the used batte for actual length.
电源主线建议出线位置
蜂鸣器
电容
Suggesting place for main power cable
请扫描二维码获取安装指南
建议您通过SpeedyBee App 扫描以获取更详细的安装指南
Scan the QR code to get the installation guide.
We recommend you scan it through the SpeedyBee App for detailed instructions.
SpeedyBee APP Facebook QR CodeInstallation Guidance
安装说明
1
12
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140
内走线推荐电机线长为110mm
1�1 标尺
1�1 Scale
Inner motor wire recommended
length: 110mm
外走线推荐电机线长为93mm
Outer motor wire recommended
length: 93mm
*(注：蜂鸣器带有 标识接飞控BZ+,
无标识接BZ-）
*Notice: connect buzzer with mark to BZ+
of ight controller, and buzzer without 符号
mark to BZ-
ESC ESC
/
