Ofna Racing 9.5 User manual
- Category
- Remote controlled toys
- Type
- User manual
READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe rusting.
• Clear oil and dirt from chassis with a electronic safe
and good experience you must observe a few rules. This degreaser.
kit is extremely fast, easily over 40MPH, and can seriously
injure someone if you are not careful. Precautions
• This kit is not a toy. Always run car with a second
Where to run car? person as a spotter and pitman.
• Any running area you choose must be dry. Do not run
car near any water or wet dirt. • Hot Parts - The pipe, manifold, engine and head are very
• Do not run on public streets. It is very easy to have the hot and will cause burns.
car run over or damaged by hitting the curb.
• Do not operate car in tight confined places. The car is • Rotating Parts - Keep hands away from the drive train,
very fast and will easily hit something. wheels, and engine when engine is running.
• Do not run near people or animals.
• Radio - Check batteries life before running the car. If
• Due to noise, you will want to consider the surrounding radio does not have full control of the car with steering
area when operating the car. and/ throttle/ or brake do not run until corrected. Failure to
• Do not operate the car at night. You will not be able to correct this will result in possible injury and damage to the
drive it without hitting something. car or property.
• Do not operate the car indoors. Engine exhaust is not
healthy. • Glow fuel - Don’t leave the glow fuel unattended with the
lid off. Fuel contains Methanol and Nitro Methane and is
Glow Fuel
• Glow fuel is poisonous! flammable and poisonous.
• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time. Store fuel in cool ventilated location. Refer the glow fuel
• Don't use any fuel other than glow fuel in this engine. label for additional precautions.
• Don't use Gasoline as fuel in glow engines!
• Car Fuel tank - Never store fuel in car tank, it will ruin the
First Time Starting the Engine engine if left in tank.
Caution! When starting engine make sure the following is
observed.
• Oil the air filter FOAM Element! OFNA #10015.. $2.95
• Set engine Master needle to 4 turns (rich setting)
• Do not do this alone, get an experienced friend to help at
first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on
receiver
• Hold car off the ground, so it will not runaway when first
starts
• Turn on Radio and check the linkage before starting
engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt
out.
Engine Break-in
• See Engine Page.
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
Storing Car After Running
• Remove fuel from tank and fuel lines
• Turn off radio in car
• Put a few drops of after run in engine to keep it from
The car is very fast
and will easily hit someone.
THINGS NEED BESIDES THE KIT
RADIO CONTROL UNIT
12V Battery for Starter Box
(must have)
Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)
AA Batteries ( 12 pcs ) for radio
Note: Carefully read the instruction manual of your
2 channel radio controller before using.
Radio must be set at neutral position
before installing in the kit.
SEQUENCE TO SET NEUTRAL
Note: Pro kit does not include engine!
Glow Fuel
20%
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the
battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral,
servo horns must be in neutral as will.
*Adjustment can be made by re-
installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
Retract the antenna. (Transmitter)
1111
12
13
REQUIRED FOR OPERATION
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
SUITABLE SERVO SIZE
29mm - 42mm
15mm - 21mm
36mm-41mm
3.5 cc (21 Class) ENGINE
REAR EXHAUST
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
TOOLS NOT INCLUDED IN KIT
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Masking Tape
Paints
Grease
Brush
More Optional Parts . . .
#10211 NiHm Battery Flat
Pack .. $29.95
# 10214 NiHm Battery Pack
Charger.. $7.95
# 51007 OFNA/Picoo Glow
Plug .. $4.95
INCLUDED WITH KIT
Shock Oil
1.5mm
Hex Wrench
Grease Box
2.5mm
Hex Wrench
3mm
Hex Wrench
5mm
Hex Wrench
7mm and 5.5mm
Hex Wrench
OFNA/Picco
O-1 bp
#51217
READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe rusting.
• Clear oil and dirt from chassis with a electronic safe
and good experience you must observe a few rules. This degreaser.
kit is extremely fast, easily over 40MPH, and can seriously
injure someone if you are not careful. Precautions
• This kit is not a toy. Always run car with a second
Where to run car? person as a spotter and pitman.
• Any running area you choose must be dry. Do not run
car near any water or wet dirt. • Hot Parts - The pipe, manifold, engine and head are very
• Do not run on public streets. It is very easy to have the hot and will cause burns.
car run over or damaged by hitting the curb.
• Do not operate car in tight confined places. The car is • Rotating Parts - Keep hands away from the drive train,
very fast and will easily hit something. wheels, and engine when engine is running.
• Do not run near people or animals.
• Radio - Check batteries life before running the car. If
• Due to noise, you will want to consider the surrounding radio does not have full control of the car with steering
area when operating the car. and/ throttle/ or brake do not run until corrected. Failure to
• Do not operate the car at night. You will not be able to correct this will result in possible injury and damage to the
drive it without hitting something. car or property.
• Do not operate the car indoors. Engine exhaust is not
healthy. • Glow fuel - Don’t leave the glow fuel unattended with the
lid off. Fuel contains Methanol and Nitro Methane and is
Glow Fuel
• Glow fuel is poisonous! flammable and poisonous.
• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time. Store fuel in cool ventilated location. Refer the glow fuel
• Don't use any fuel other than glow fuel in this engine. label for additional precautions.
• Don't use Gasoline as fuel in glow engines!
• Car Fuel tank - Never store fuel in car tank, it will ruin the
First Time Starting the Engine engine if left in tank.
Caution! When starting engine make sure the following is
observed.
• Oil the air filter FOAM Element! OFNA #10015.. $2.95
• Set engine Master needle to 4 turns (rich setting)
• Do not do this alone, get an experienced friend to help at
first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on
receiver
• Hold car off the ground, so it will not runaway when first
starts
• Turn on Radio and check the linkage before starting
engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt
out.
Engine Break-in
• See Engine Page.
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
Storing Car After Running
• Remove fuel from tank and fuel lines
• Turn off radio in car
• Put a few drops of after run in engine to keep it from
The car is very fast
and will easily hit someone.
THINGS NEED BESIDES THE KIT
RADIO CONTROL UNIT
12V Battery for Starter Box
(must have)
Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)
AA Batteries ( 12 pcs ) for radio
Note: Carefully read the instruction manual of your
2 channel radio controller before using.
Radio must be set at neutral position
before installing in the kit.
SEQUENCE TO SET NEUTRAL
Note: Pro kit does not include engine!
Glow Fuel
20%
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the
battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral,
servo horns must be in neutral as will.
*Adjustment can be made by re-
installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
Retract the antenna. (Transmitter)
1111
12
13
REQUIRED FOR OPERATION
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
SUITABLE SERVO SIZE
29mm - 42mm
15mm - 21mm
36mm-41mm
3.5 cc (21 Class) ENGINE
REAR EXHAUST
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
TOOLS NOT INCLUDED IN KIT
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Masking Tape
Paints
Grease
Brush
More Optional Parts . . .
#10211 NiHm Battery Flat
Pack .. $29.95
# 10214 NiHm Battery Pack
Charger.. $7.95
# 51007 OFNA/Picoo Glow
Plug .. $4.95
INCLUDED WITH KIT
Shock Oil
1.5mm
Hex Wrench
Grease Box
2.5mm
Hex Wrench
3mm
Hex Wrench
5mm
Hex Wrench
7mm and 5.5mm
Hex Wrench
OFNA/Picco
O-1 bp
#51217
40003
DIFF. CASE
PLASTIC PARTS
40017
GEAR BOX PLASTIC PARTS
13
2
PLASTIC PARTS
36060
FRONT C HUB PLASTIC PARTS
40015
ARM HOLDER PLASTIC PARTS 40016
UPPER ARM PLASTIC PARTS
40020
FRONT AND REAR LOWER ARM PLASTIC PARTS
40027
WING SUPPORT PLASTIC PARTS 40013 & 40048
FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
36081
REAR UPRIGHT
Front Upper Arm Ball End
36690
PLASTIC PARTS
40031
SERVO SAVER PLASTIC PARTS 40047
RECEIVER BOX PLASTIC PARTS
40040
CENTER DIFF. MOUNT PLASTIC PARTS
40046
STONE GUARD PLASTIC PARTS
40018/40029
CHASSIS BRACE PLASTIC PARTS
40056
SHOCK ABSORBER PLASTIC PARTS
40003
DIFF. CASE
PLASTIC PARTS
40017
GEAR BOX PLASTIC PARTS
13
2
PLASTIC PARTS
36060
FRONT C HUB PLASTIC PARTS
40015
ARM HOLDER PLASTIC PARTS 40016
UPPER ARM PLASTIC PARTS
40020
FRONT AND REAR LOWER ARM PLASTIC PARTS
40027
WING SUPPORT PLASTIC PARTS 40013 & 40048
FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
36081
REAR UPRIGHT
Front Upper Arm Ball End
36690
PLASTIC PARTS
40031
SERVO SAVER PLASTIC PARTS 40047
RECEIVER BOX PLASTIC PARTS
40040
CENTER DIFF. MOUNT PLASTIC PARTS
40046
STONE GUARD PLASTIC PARTS
40018/40029
CHASSIS BRACE PLASTIC PARTS
40056
SHOCK ABSORBER PLASTIC PARTS
4x4mm
Set Screw
4x4mm
Set Screw
ASSEMBLY OF THE DIFFERENTIAL CASE
40006
Cap Joint
40006
Cap Joint
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40009
P6 O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40003
Diff. Case
40003
Diff. Case
40005
Break
Cap Joint
40005
Break
Cap Joint
(Builds one differential for Center)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
(Builds one differential for Center)
40002
Large
Bevel Gear
40002
Large
Bevel Gear
40011
Diff. Gasket
40011
Diff. Gasket
3x12mm
Flat Head
Tapping Screw
3x12mm
Flat Head
Tapping Screw
40001
47T
Spur Gear
40001
47T
Spur Gear
*Use 6x15mm washer
to adjust the gear mesh.
*Use 6x15mm washer
to adjust the gear mesh.
Note: It is very important to add
or remove the #30779 washer if
the gear mesh is too tight or
too lose.
( Builds two differentials for front and rear.)
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer 30773
4mm
Cross pin
30773
4mm
Cross pin
* Apply diff. gear grease to the
differential during assembly.
* Fill the diff. the case to
approx 70% with grease.
ASSEMBLY OF THE DIFFERENTIAL GEAR ASSEMBLY OF THE FRONT GEAR BOX
ASSEMBLY OF THE FRONT ARMS HOLDER
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40024
13x16x0.2mm
Shim
40024
13x16x0.2mm
Shim
40021
14T Small
Bevel Gear..............1
40021
14TSmall
Bevel Gear
* Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
4x15mm
Tapping Screw
(Small Head)
4x45mm
Tapping Screw
(Small Head)
40022
Front Lower Arm
Holder (Front)
90026
5x5mm
Set Screw
36730
Cap Joint
36730
Cap Joint................................1
40015
Front Lower arm
Holder (Rear/Plastic)
40015
Front Upper arm
Holder (Rear/Plastic)
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw.......................4
4x15mm
Tapping Screw........................2
4x45mm
Tapping Screw........................2
90026
5x5mm
Set Screw......1
Screw
Cement
36053
8X16mm
Ball bearing
OPTION: #49001 HD STEEL GEAR
SET, INSIDE DIFF.
OPTION:
#49016 SPUR GEAR 50T, HD
#49030 SPUR GEAR 50T, HD SPECIAL
#49032 SPUR GEAR 51T,HD
36053
8X16mm
Ball bearing
OPTION: #49002 CNC 7075
FRONT LOWER ARM HOLDER
OPTION: #49012 PINION GEAR
13TOOTH
MISC. SCREW BAG
40067
Use shims to adjust gear
mesh.
4x4mm
Set Screw
4x4mm
Set Screw
ASSEMBLY OF THE DIFFERENTIAL CASE
40006
Cap Joint
40006
Cap Joint
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40009
P6 O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40003
Diff. Case
40003
Diff. Case
40005
Break
Cap Joint
40005
Break
Cap Joint
(Builds one differential for Center)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
(Builds one differential for Center)
40002
Large
Bevel Gear
40002
Large
Bevel Gear
40011
Diff. Gasket
40011
Diff. Gasket
3x12mm
Flat Head
Tapping Screw
3x12mm
Flat Head
Tapping Screw
40001
47T
Spur Gear
40001
47T
Spur Gear
*Use 6x15mm washer
to adjust the gear mesh.
*Use 6x15mm washer
to adjust the gear mesh.
Note: It is very important to add
or remove the #30779 washer if
the gear mesh is too tight or
too lose.
( Builds two differentials for front and rear.)
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer 30773
4mm
Cross pin
30773
4mm
Cross pin
* Apply diff. gear grease to the
differential during assembly.
* Fill the diff. the case to
approx 70% with grease.
ASSEMBLY OF THE DIFFERENTIAL GEAR ASSEMBLY OF THE FRONT GEAR BOX
ASSEMBLY OF THE FRONT ARMS HOLDER
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40024
13x16x0.2mm
Shim
40024
13x16x0.2mm
Shim
40021
14T Small
Bevel Gear..............1
40021
14TSmall
Bevel Gear
* Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
4x15mm
Tapping Screw
(Small Head)
4x45mm
Tapping Screw
(Small Head)
40022
Front Lower Arm
Holder (Front)
90026
5x5mm
Set Screw
36730
Cap Joint
36730
Cap Joint................................1
40015
Front Lower arm
Holder (Rear/Plastic)
40015
Front Upper arm
Holder (Rear/Plastic)
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw.......................4
4x15mm
Tapping Screw........................2
4x45mm
Tapping Screw........................2
90026
5x5mm
Set Screw......1
Screw
Cement
36053
8X16mm
Ball bearing
OPTION: #49001 HD STEEL GEAR
SET, INSIDE DIFF.
OPTION:
#49016 SPUR GEAR 50T, HD
#49030 SPUR GEAR 50T, HD SPECIAL
#49032 SPUR GEAR 51T,HD
36053
8X16mm
Ball bearing
OPTION: #49002 CNC 7075
FRONT LOWER ARM HOLDER
OPTION: #49012 PINION GEAR
13TOOTH
MISC. SCREW BAG
40067
Use shims to adjust gear
mesh.
M3x12
TP Screw
M4x15
TP Screw
4mm
Nylon Nut
ASSEMBLY OF THE FRONT KNUCKLE ARMS
ASSEMBLY OF THE FRONT SHOCK TOWER
R
L
L
36051
Alloy Front
Knuckle Arm
36051
Alloy Front
Knuckle Arm
* "R" for right hand
side.
36052
8mm CVA Joint
(Long/Front)
36052
8mm CVA Joint
(Long/Front)
36053
8x16x5mm
Ball bearing
90026
5mm
Set Screw
90026
5mm
Set Screw
36054
Alum.
Wheel Hub 8mm
36054
Alum.
Wheel Hub 8mm
36055
2.5x17mm
Pin
36055
2.5x17mm
Pin
36870
4x10mm
Cap Screw
36870
4x10mm
Cap Screw
36870
4x10mm
Cap Screw
36870
4x10mm
Cap Screw
36120
Knuckle Arm
Bushing
36120
Knuckle Arm
Bushing
36120
Knuckle Arm
Bushing
36120
Knuckle Arm
Bushing
* insert knuckle arm bushing
before assembly knuckle arm.
36060
Front C Hub
(Right)
36060
Front C Hub
(Left)
OPTION: #36516 CNC ALUM
STEERING KNUCKLES.
40014
Front
Shock Tower
Screw
Cement
Screw
Cement
Screw
Cement
Screw
Cement
ASSEMBLY OF THE FRONT SUSPENSION ARMS
40023
Lower Arm Shaft (4mm)
3mm
E-Ring
3mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
4X10mm
Set Screw
36170
Arm Shaft
3mm
36170
Arm Shaft
3mm
40020
Front
Lower Arm
36860
5x40mm
Turnbuckle
40016
Front
Upper Arm
36850
7mm Ball
36690
7mm
Plastic Arm
Ball End
3x25mm
Set Screw
3mm
Nylon Nut
* A 4 x 10mm set screw is used
to adjust the ride height.
OPTION: #49003 CNC 7075 FRONT SHOCK
TOWER.
36053
8x16x5mm
Ball bearing 36053
8x16x5mm
Ball bearing
36053
8x16x5mm
Ball bearing
SPECIAL NOTE
3x3mm
Set Screw
Screw in the 3mm set screws
to lock in the hinge pins.
*Note: Do not over tighten..
Apply screw
cement into
Hole, not
screw or
bushing.
Apply screw
cement into
Hole, not
screw or
bushing.
M3x12
TP Screw
M4x15
TP Screw
4mm
Nylon Nut
ASSEMBLY OF THE FRONT KNUCKLE ARMS
ASSEMBLY OF THE FRONT SHOCK TOWER
R
L
L
36051
Alloy Front
Knuckle Arm
36051
Alloy Front
Knuckle Arm
* "R" for right hand
side.
36052
8mm CVA Joint
(Long/Front)
36052
8mm CVA Joint
(Long/Front)
36053
8x16x5mm
Ball bearing
90026
5mm
Set Screw
90026
5mm
Set Screw
36054
Alum.
Wheel Hub 8mm
36054
Alum.
Wheel Hub 8mm
36055
2.5x17mm
Pin
36055
2.5x17mm
Pin
36870
4x10mm
Cap Screw
36870
4x10mm
Cap Screw
36870
4x10mm
Cap Screw
36870
4x10mm
Cap Screw
36120
Knuckle Arm
Bushing
36120
Knuckle Arm
Bushing
36120
Knuckle Arm
Bushing
36120
Knuckle Arm
Bushing
* insert knuckle arm bushing
before assembly knuckle arm.
36060
Front C Hub
(Right)
36060
Front C Hub
(Left)
OPTION: #36516 CNC ALUM
STEERING KNUCKLES.
40014
Front
Shock Tower
Screw
Cement
Screw
Cement
Screw
Cement
Screw
Cement
ASSEMBLY OF THE FRONT SUSPENSION ARMS
40023
Lower Arm Shaft (4mm)
3mm
E-Ring
3mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
4X10mm
Set Screw
36170
Arm Shaft
3mm
36170
Arm Shaft
3mm
40020
Front
Lower Arm
36860
5x40mm
Turnbuckle
40016
Front
Upper Arm
36850
7mm Ball
36690
7mm
Plastic Arm
Ball End
3x25mm
Set Screw
3mm
Nylon Nut
* A 4 x 10mm set screw is used
to adjust the ride height.
OPTION: #49003 CNC 7075 FRONT SHOCK
TOWER.
36053
8x16x5mm
Ball bearing 36053
8x16x5mm
Ball bearing
36053
8x16x5mm
Ball bearing
SPECIAL NOTE
3x3mm
Set Screw
Screw in the 3mm set screws
to lock in the hinge pins.
*Note: Do not over tighten..
Apply screw
cement into
Hole, not
screw or
bushing.
Apply screw
cement into
Hole, not
screw or
bushing.
3X12mm
Tapping Screw
* Insert the front bumper
before assembly.
3x8mm
Set Screw
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
3x3
Set Screw
3x3
Set Screw
40019
Stabilizer
3x10mm
Flat Head
Tapping Screw
3x10mm
Flat Head
Tapping Screw
3x3mm
Set Screw
40018
Stabilizer
Mount Plastic
40013
Front
Bumper
40064
Chassis
Hard Coated
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
30341
Stabilizer Ball
30341
Stabilizer Ball..........2
ASSEMBLY OF THE FRONT STABILIZER
3 x 10mm
Flat Head
Tapping Screw........2
4 x 16mm
Flat Head
Tapping Screw..........4
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
3 x 3mm
Set Screw..............4
ASSEMBLY OF THE REAR GEAR BOX
4X16mm
Tapping Screw
(Small Head)
4X15mm
Tapping Screw
(Small Head)
4X10mm
Tapping Screw
(Small Head)
4X45mm
Flat Head
Tapping Screw
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
40024
13x16x0.2mm
Shim
40021
14T Pinion
Gear * Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
1.5
2
3
5x4mm
Set Screw
36730
Cap Joint
40025
Rear
Lower Arm Holder
( 0 Degree)
4mm
Nylon Nut
4 x 15mm
Tapping Screw
( Small Head )..........6
4mm
Nylon Nut..............2
5 x 5mm
Set Screw..............1
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40021
14T Pinion
Bevel Gear..............1
36730
Cap Joint.................1
4 x 20mm
Flat Head
Tapping Screw..........2
40027
Wing Stay
Mount
40015
Rear arm Holder
Screw
Cement
OPTION: #49007 CNC REAR
LOWER ANTI-SQUAT HOLDERS -
1.5; 2.0; 3.0 DEGREES.
OPTION: #49012 PINION GEAR
13TOOTH
3X12mm
Tapping Screw
* Insert the front bumper
before assembly.
3x8mm
Set Screw
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
3x3
Set Screw
3x3
Set Screw
40019
Stabilizer
3x10mm
Flat Head
Tapping Screw
3x10mm
Flat Head
Tapping Screw
3x3mm
Set Screw
40018
Stabilizer
Mount Plastic
40013
Front
Bumper
40064
Chassis
Hard Coated
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
30341
Stabilizer Ball
30341
Stabilizer Ball..........2
ASSEMBLY OF THE FRONT STABILIZER
3 x 10mm
Flat Head
Tapping Screw........2
4 x 16mm
Flat Head
Tapping Screw..........4
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
3 x 3mm
Set Screw..............4
ASSEMBLY OF THE REAR GEAR BOX
4X16mm
Tapping Screw
(Small Head)
4X15mm
Tapping Screw
(Small Head)
4X10mm
Tapping Screw
(Small Head)
4X45mm
Flat Head
Tapping Screw
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
40024
13x16x0.2mm
Shim
40021
14T Pinion
Gear * Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
1.5
2
3
5x4mm
Set Screw
36730
Cap Joint
40025
Rear
Lower Arm Holder
( 0 Degree)
4mm
Nylon Nut
4 x 15mm
Tapping Screw
( Small Head )..........6
4mm
Nylon Nut..............2
5 x 5mm
Set Screw..............1
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40021
14T Pinion
Bevel Gear..............1
36730
Cap Joint.................1
4 x 20mm
Flat Head
Tapping Screw..........2
40027
Wing Stay
Mount
40015
Rear arm Holder
Screw
Cement
OPTION: #49007 CNC REAR
LOWER ANTI-SQUAT HOLDERS -
1.5; 2.0; 3.0 DEGREES.
OPTION: #49012 PINION GEAR
13TOOTH
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE WING STAY
40027
Rear
Body Mount
( Take the plastic part from #40027Rear Win Stay Set. )
40026
Rear
Shock Tower
3x12mm
Tapping Screw
3mm
Nylon Nut
40027
Wing Mount
40027
Wing Mount
*Insert the 3mm nylon nut
before assembly.
3x20
Tapping Screw
3x20
Tapping Screw
40027
Wing Stay
( Left )
40027
Wing Stay
( Right )
40027
Wing Mount
40027
Wing Mount
40027
Wing Stay
Post
3x12mm
Tapping Screw
4x15mm
Tapping Screw
( Small Head )
4x15mm
Tapping Screw
( Small Head )
3 x 20mm
Tapping Screw............6
4 x 15mm
Tapping Screw
( Small Head )............2
4 x 15mm
Tapping Screw
( Small Head )............4
3mm
Nylon Nut........2
3 x 12mm
Tapping Screw........3
ASSEMBLY OF THE REAR WHEEL HUB
ASSEMBLY OF THE REAR UPPER ARMS
40023
Lower Arm Shaft
3mm
E-Ring
3mm
E-Ring
3mm
E-Ring
3mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
4X10mm
Set Screw
36170
3mm
Arm Shaft
36860
5x40mm
Turnbuckle
36053
8x16x5mm
Ball bearing
36053
8x16x5mm
Ball bearing
5mm
Set Screw
36054
8mm
Wheel Hub
36055
2.5x17mm
Pin
40020
Rear Lower Arm
36850
7mm Ball
36850
7mm Ball
(Make two upper arms for left an right hand side. )
36081
Rear
Upper Right
36082
Rear Wheel Shaft
3mm
Plastic Washer
3mm
Plastic
Washer
Assembly of the right and left hand side
are the same.
4 x 10 mm
Set Screw...........2
5 x 5mm
Set Screw............2
2.5mm
E-Ring..........4
3 mm
E-Ring..........4
40018
Upper Arm
Plastic Rod End
15mm
* A 4 x 10mm set screw is used
to adjust the ride height.
0 10 20 30 40 50
mm
OPTION: #49004 CNC 7075 REAR
SHOCK TOWER
OPTION: #49023 CNC ALIM.
POSTS, WING MOUNT
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
36860
5x40mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
SPECIAL NOTE
3x3mm
Set Screw
Screw in the 3mm set screws
to lock in the hinge pins.
*Note: Do not over tighten.
Screw
Cement
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE WING STAY
40027
Rear
Body Mount
( Take the plastic part from #40027Rear Win Stay Set. )
40026
Rear
Shock Tower
3x12mm
Tapping Screw
3mm
Nylon Nut
40027
Wing Mount
40027
Wing Mount
*Insert the 3mm nylon nut
before assembly.
3x20
Tapping Screw
3x20
Tapping Screw
40027
Wing Stay
( Left )
40027
Wing Stay
( Right )
40027
Wing Mount
40027
Wing Mount
40027
Wing Stay
Post
3x12mm
Tapping Screw
4x15mm
Tapping Screw
( Small Head )
4x15mm
Tapping Screw
( Small Head )
3 x 20mm
Tapping Screw............6
4 x 15mm
Tapping Screw
( Small Head )............2
4 x 15mm
Tapping Screw
( Small Head )............4
3mm
Nylon Nut........2
3 x 12mm
Tapping Screw........3
ASSEMBLY OF THE REAR WHEEL HUB
ASSEMBLY OF THE REAR UPPER ARMS
40023
Lower Arm Shaft
3mm
E-Ring
3mm
E-Ring
3mm
E-Ring
3mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
4X10mm
Set Screw
36170
3mm
Arm Shaft
36860
5x40mm
Turnbuckle
36053
8x16x5mm
Ball bearing
36053
8x16x5mm
Ball bearing
5mm
Set Screw
36054
8mm
Wheel Hub
36055
2.5x17mm
Pin
40020
Rear Lower Arm
36850
7mm Ball
36850
7mm Ball
(Make two upper arms for left an right hand side. )
36081
Rear
Upper Right
36082
Rear Wheel Shaft
3mm
Plastic Washer
3mm
Plastic
Washer
Assembly of the right and left hand side
are the same.
4 x 10 mm
Set Screw...........2
5 x 5mm
Set Screw............2
2.5mm
E-Ring..........4
3 mm
E-Ring..........4
40018
Upper Arm
Plastic Rod End
15mm
* A 4 x 10mm set screw is used
to adjust the ride height.
0 10 20 30 40 50
mm
OPTION: #49004 CNC 7075 REAR
SHOCK TOWER
OPTION: #49023 CNC ALIM.
POSTS, WING MOUNT
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
36860
5x40mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
SPECIAL NOTE
3x3mm
Set Screw
Screw in the 3mm set screws
to lock in the hinge pins.
*Note: Do not over tighten.
Screw
Cement
ASSEMBLY OF THE REAR ANTI-ROLL BAR
3x3
Set Screw
3x3
Set Screw
3x3
Set Screw
3X10mm
Flat Head
Screw
3X10mm
Flat Head
Screw
40019
Stabilizer
40018
Stabilizer
Mount Plastic
30341
Stabilizer Ball..........2
3 x 10mm
Flat Head
Tapping Screw........2
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
3 x 3mm
Set Screw..............2
3 x 20mm
Cap Screw..........2
3 X 25mm
Cap Screw.........2
M3
Nylon Nut..........2
3 x 3mm
Set Screw..........2
3 x 8mm
et Screw..........2.
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
30341
Stabilizer Ball
3x8mm
Set Screw
3mm
Nylon Nut
3mm
Nylon Nut
3 x 25mm
Cap Screw
3 x 20mm
Cap Screw
36110
Rear
Driver Shaft
* Insert rear dog bone before assembly.
Rear Upper Arm
Assembly
Assembly of the right and left hand side
are the same.
ASSEMBLY OF THE SERVO SAVER
4 x 16mm
Flat Head
Tapping Screw..........4
4 x 16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE REAR GEAR BOX ON TO CHASSIS
40064
Chassis
M3 Nut
* Put the 3mm
nut before assembly.
40031
Servo Saver
Horn A 40032
Servo Saver
Connecting Plate
6x10mm
Plastic
Bushing
6x10mm
Plastic
Bushing
Servo Saver
Horn C
4x8mm
Plastic flange
Bushing
J-33
Steering
Screw...........2
40037
Steering Plate
Hex Screw
40037
Steering Plate
Hex Screw
40035
Servo Saver
Alum. Axle
Tube
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
Servo Saver
Spring Tension
Adjuster
40036
servo Saver
Post 40036
Servo Saver
Post
40074
6x10mm
Ball bearing
M3 Nut..........1
4x10mm
Screw..........2
* Take the 4x8mm Plastic Flange bushing
and Plastic Bushing from servo saver plastic
parts tree
OPTION: #49014 CNC BALL
BEARING AXLE TUBE
Option:
40073
4x8mm
Ball bearing
flange
40037
Steering Plat
Hex Screw....... 2
Option:
40074
6x10mm
Ball bearing
ASSEMBLY OF THE REAR ANTI-ROLL BAR
3x3
Set Screw
3x3
Set Screw
3x3
Set Screw
3X10mm
Flat Head
Screw
3X10mm
Flat Head
Screw
40019
Stabilizer
40018
Stabilizer
Mount Plastic
30341
Stabilizer Ball..........2
3 x 10mm
Flat Head
Tapping Screw........2
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
3 x 3mm
Set Screw..............2
3 x 20mm
Cap Screw..........2
3 X 25mm
Cap Screw.........2
M3
Nylon Nut..........2
3 x 3mm
Set Screw..........2
3 x 8mm
et Screw..........2.
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
30341
Stabilizer Ball
3x8mm
Set Screw
3mm
Nylon Nut
3mm
Nylon Nut
3 x 25mm
Cap Screw
3 x 20mm
Cap Screw
36110
Rear
Driver Shaft
* Insert rear dog bone before assembly.
Rear Upper Arm
Assembly
Assembly of the right and left hand side
are the same.
ASSEMBLY OF THE SERVO SAVER
4 x 16mm
Flat Head
Tapping Screw..........4
4 x 16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE REAR GEAR BOX ON TO CHASSIS
40064
Chassis
M3 Nut
* Put the 3mm
nut before assembly.
40031
Servo Saver
Horn A 40032
Servo Saver
Connecting Plate
6x10mm
Plastic
Bushing
6x10mm
Plastic
Bushing
Servo Saver
Horn C
4x8mm
Plastic flange
Bushing
J-33
Steering
Screw...........2
40037
Steering Plate
Hex Screw
40037
Steering Plate
Hex Screw
40035
Servo Saver
Alum. Axle
Tube
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
Servo Saver
Spring Tension
Adjuster
40036
servo Saver
Post 40036
Servo Saver
Post
40074
6x10mm
Ball bearing
M3 Nut..........1
4x10mm
Screw..........2
* Take the 4x8mm Plastic Flange bushing
and Plastic Bushing from servo saver plastic
parts tree
OPTION: #49014 CNC BALL
BEARING AXLE TUBE
Option:
40073
4x8mm
Ball bearing
flange
40037
Steering Plat
Hex Screw....... 2
Option:
40074
6x10mm
Ball bearing
4x10mm
Flat Head
Screw
4x10mm
Screw
4x15mm
Tapping Screw
40027
Front Body
Post
3x12mm
Screw
* Assembly the front body post
before assembly the Front Plate.
40030
Front Plate
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS
36790
4x46mm
Turnbuckle
40023
4x46mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
36700
Steering
Ball End
36700
Steering
Ball End
36700
Steering
Ball End
3mm
Nylon Nut
40039
3mm Tapper
Washer(Alum.)
400393mm Tapper
Washer(Alum.)
J-35
Alum. Tapper
Washer................4
3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw
ASSEMBLY OF THE FRONT STEERING ROD
4x10mm
Screw..........2
3 x 12mm
Tapping Screw..........1
M3
Nylon Nut..........2
4 x 15mm
Tapping Screw
( Small Head )............2
3 x 15mm
Flat Head
Screw..........4
4 x 10mm
Flat Head Screw..........2
Assembly of the right and left hand side
are the same.
0 10 20 30 40 50
mm
* Anticlockwise mark.
29mm
* Make two steering rods for left and right-hand side.
6x12x0.3mm
Washer
* Take off the double sided paper
before assembly.
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side.
36660
Brake Pad
36661
Brake Pad
linings
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40045
Brake Pad
Adjustment Screw
40045
Brake Pad
Adjustment Screw
40043
Center Diff. Mount
Post
40040
Break Disc
Holder
40040
Brake Disk
Holder 40040
Brake Disc
Holder
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40046
Brake Pad Screw...........4
40044
Brake Pad
Spring.........8
40043
Center Diff. Mount
Post...........................4
Large
Hole
Small
Hole
Assembly the brake disc holder
in the direction shown.
*Towards
the front.
*Towards
the Rear.
Small hole to the
Outside.
OPTION:
#49005 CNC 7075 FRONT PLATE
#49019 GRAPHITE FRONT PLATE
40075
40039
3mm Tapper
Washer(Alum.).......4
OPTION: #49030 CNC 7075 SPLIT
CENTER DIFF MOUNT.
4x10mm
Flat Head
Screw
4x10mm
Screw
4x15mm
Tapping Screw
40027
Front Body
Post
3x12mm
Screw
* Assembly the front body post
before assembly the Front Plate.
40030
Front Plate
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS
36790
4x46mm
Turnbuckle
40023
4x46mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
36700
Steering
Ball End
36700
Steering
Ball End
36700
Steering
Ball End
3mm
Nylon Nut
40039
3mm Tapper
Washer(Alum.)
400393mm Tapper
Washer(Alum.)
J-35
Alum. Tapper
Washer................4
3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw
ASSEMBLY OF THE FRONT STEERING ROD
4x10mm
Screw..........2
3 x 12mm
Tapping Screw..........1
M3
Nylon Nut..........2
4 x 15mm
Tapping Screw
( Small Head )............2
3 x 15mm
Flat Head
Screw..........4
4 x 10mm
Flat Head Screw..........2
Assembly of the right and left hand side
are the same.
0 10 20 30 40 50
mm
* Anticlockwise mark.
29mm
* Make two steering rods for left and right-hand side.
6x12x0.3mm
Washer
* Take off the double sided paper
before assembly.
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side.
36660
Brake Pad
36661
Brake Pad
linings
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40045
Brake Pad
Adjustment Screw
40045
Brake Pad
Adjustment Screw
40043
Center Diff. Mount
Post
40040
Break Disc
Holder
40040
Brake Disk
Holder 40040
Brake Disc
Holder
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40046
Brake Pad Screw...........4
40044
Brake Pad
Spring.........8
40043
Center Diff. Mount
Post...........................4
Large
Hole
Small
Hole
Assembly the brake disc holder
in the direction shown.
*Towards
the front.
*Towards
the Rear.
Small hole to the
Outside.
OPTION:
#49005 CNC 7075 FRONT PLATE
#49019 GRAPHITE FRONT PLATE
40075
40039
3mm Tapper
Washer(Alum.).......4
OPTION: #49030 CNC 7075 SPLIT
CENTER DIFF MOUNT.
40042
Brake Disk 40042
Brake Disk
40042
Brake Disk 40042
Brake Disk
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
Center Diff. Assembly
3x3mm
Set Screw
3x3mm
Set Screw
3x10mm
Screw
40031
Fuel Overflow
Proof Plate
30213
Brake Cam
30211
Plastic
Bushing
Option
30212
5X8mm
Ball Bearing
40041
Center Diff.
Plate
30171
Brake Lever
30171
Brake Lever..........2
30171
Brake Lever
3x10mm
Screw
4x10mm
Screw..........4
3 x 3mm
Set Screw..............2
Put the front brake lever as
Shown.
40028
Center Drive
Shaft (93mm)
40028
Center Drive
Shaft (93mm)
4x12mm
Flat Head
Screw
3x25mm
Cap Screw
3mm
Nylon Nut
40018
Center Chassis
Brace
( Rear )
40018
Center Chassis
Brace
( Front )
3x12mm
Screw
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
2.6x10mm
Flat Head
Tapping Screw
3mm
Nylon Nut........1
3 x 12mm
Tapping Screw........3
3 X 25mm
Cap Screw.........1
4 x 12mm
Flat Head Screw..........2
4 x 16mm
Flat Head
Tapping Screw..........4
ASSEMBLY OF THE CENTER DIFF.
Assembly of the center stiffener onto chassis
OPTION: #49008 GRAPHITE
BRAKE DISKS, 2PCS.
OPTION: #49018 GRAPHITE TOP
CENTER PLATE
OPTION: #49015 CNC ALUM.
FRONT & REAR CHASSIS
BRACES
Screw
Cement
Screw
Cement
Screw
Cement
40042
Brake Disk 40042
Brake Disk
40042
Brake Disk 40042
Brake Disk
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
Center Diff. Assembly
3x3mm
Set Screw
3x3mm
Set Screw
3x10mm
Screw
40031
Fuel Overflow
Proof Plate
30213
Brake Cam
30211
Plastic
Bushing
Option
30212
5X8mm
Ball Bearing
40041
Center Diff.
Plate
30171
Brake Lever
30171
Brake Lever..........2
30171
Brake Lever
3x10mm
Screw
4x10mm
Screw..........4
3 x 3mm
Set Screw..............2
Put the front brake lever as
Shown.
40028
Center Drive
Shaft (93mm)
40028
Center Drive
Shaft (93mm)
4x12mm
Flat Head
Screw
3x25mm
Cap Screw
3mm
Nylon Nut
40018
Center Chassis
Brace
( Rear )
40018
Center Chassis
Brace
( Front )
3x12mm
Screw
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
2.6x10mm
Flat Head
Tapping Screw
3mm
Nylon Nut........1
3 x 12mm
Tapping Screw........3
3 X 25mm
Cap Screw.........1
4 x 12mm
Flat Head Screw..........2
4 x 16mm
Flat Head
Tapping Screw..........4
ASSEMBLY OF THE CENTER DIFF.
Assembly of the center stiffener onto chassis
OPTION: #49008 GRAPHITE
BRAKE DISKS, 2PCS.
OPTION: #49018 GRAPHITE TOP
CENTER PLATE
OPTION: #49015 CNC ALUM.
FRONT & REAR CHASSIS
BRACES
Screw
Cement
Screw
Cement
Screw
Cement
ASSEMBLY OF THE STONE GUARD
ASSEMBLY OF THE RECEIVER BOX
40046
Stone Guard
40046
Stone Guard
3x10mm
Screw
3x10mm
Screw
3x10mm
Screw
Assembly of the right and left hand side
are the same.
* Use the screw provided
with your radio
10280
Switch Cover
Switch, Provided by Radio
40047
Receiver Box
40047
Receiver Box
Cover
40047
Receiver Box
2x10mm
Tapping Screw
3x25mm
Screw
Receiver
Battery Case,
Provided by
Radio
30560
Antenna
Pipe
3 x 10mm
Tapping Screw..........6
3 x 10mm
Tapping Screw..........1
3x10mm
Screw
2 x 25mm Screw.....1
2 x10mm
Tapping Screw..........2
Option:
10212
Hump Pack
Battery
*Use the original battery
case or rechargeable
hump pack battery.
* You must add padding for radio
and battery once lid is closed.
Do not let radio and/or battery be
loose in box.
3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
receiver box.
* Use 4 pcs for
radio tray.
3x10mm
Flat Head
Tapping Screw
40027
Radio Tray
Post
( Plastic )
40027
Radio Tray
Post
( Plastic )
3x12mm
Tapping Screw
Servo Post
Servo Post
3x10mm
Tapping Screw
3x10mm
Tapping Screw
3x10
Tapping Screw
3x10
Tapping Screw
* Take the servo post
from servo saver plastic
part tree.
ASSEMBLY OF THE RADIO TRAY
3 x 10mm
Flat Head
Tapping Screw.........8
3 x 10mm
Tapping Screw..........14
Throttle
Servo
Steering
Servo
*Connect as per radio.
40049
Alum.
Radio Tray
3X10mm
Tapping Screw
40031
Transponder
Holder
OPTION: #49017 GRAPHITE
RADIO TRAY.
OPTION: #49022 CNC ALUM.
POST, RADIO TRAY
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
Ofna Racing 9.5 User manual
- Category
- Remote controlled toys
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
THUNDER TIGER DUCATI 999R User manual
-
Dometic DCMW11B.F Installation guide
-
Magic Home JE-DTT16W-DTL3G User manual
-
Warrior Products 7020 Installation guide
-
protech megaMAX Owner's manual
-
Kyosho SUPER EIGHT GP20 LANDMAX2 4WD User manual
-
Duratrax 835B Specification
-
-
-
Team Associated RC8T4e Team Kit User manual
