Ofna Racing 9.5 MBX User manual

Brand
Ofna Racing
Model
9.5 MBX
Category
Remote controlled toys
Type
User manual

Ofna Racing 9.5 MBX is an unparalleled nitro-powered, off-road vehicle offering thrilling speeds exceeding 40 mph. It boasts a robust chassis with adjustable features for precision handling. The vehicle requires a 20% nitro glow fuel and runs best with OFNA/Picco Long Glow Plugs. Moreover, it necessitates batteries for the transmitter and receiver packs. To ensure safety, always have a second person present as a spotter and pitman.

Ofna Racing 9.5 MBX is an unparalleled nitro-powered, off-road vehicle offering thrilling speeds exceeding 40 mph. It boasts a robust chassis with adjustable features for precision handling. The vehicle requires a 20% nitro glow fuel and runs best with OFNA/Picco Long Glow Plugs. Moreover, it necessitates batteries for the transmitter and receiver packs. To ensure safety, always have a second person present as a spotter and pitman.

OFNA Racing
22692 Granite Way, Ste. B
Laguna Hills, Ca. 92653
(949) 586-2910
Www.ofna.com
RTR Instruction
Manual
MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe • Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This Precautions
kit is extremely fast, easily over 40MPH, and can seriously • This kit is not a toy. Always run car with a second
injure someone if you are not careful. person as a spotter and pitman.
Where to run car? • Hot Parts - The pipe, manifold, engine and head are very
• Any running area you choose must be dry. Do not run hot and will cause burns.
car near any water or wet dirt.
• Do not run on public streets. It is very easy to have the • Rotating Parts - Keep hands away from the drive train,
car run over or damaged by hitting the curb. wheels, and engine when engine is running.
• Do not operate car in tight confined places. The car is
very fast and will easily hit something. • Radio - Check batteries life before running the car. If
• Do not run near people or animals. radio does not have full control of the car with steering
and/or throttle/brake do not run until corrected. Failure to
• Due noise, you will want to consider the surrounding correct this will result in possible injury and damage to the
area when operating the car. car or property.
• Do not operate the car at night. You will not be able to
drive it without hitting something. • Glow fuel - Do leave the glow fuel unattended with the lid
• Do not operate the car indoors. Engine exhaust is not off. Fuel contains Methanol and Nitro Methane and is
healthy. flammable and poisonous.
Glow Fuel Store fuel in cool ventilated location. Refer the glow fuel
• Glow fuel is poisonous!
• Glow fuel is flammable! label for additional precautions.
• Do not leave in fuel bottle with lid off at any time.
• Do not use any fuel other than glow fuel in this engine. • Car Fuel tank - Never store fuel in car tank, it will ruin the
engine if left in tank.
First Time Starting the Engine
Caution! When starting engine make sure the following is • Always turn off the car BEFORE turning off radio.
observed.
• Set engine Master needle to 3 turns (rich setting) • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
• Do not do this alone, get an experienced friend to help at ISSUE.
first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on IF YOU DO NOT BREAK-IN ENGINE
receiver CORRECTLY, MAINLY AT LOW RPM,
• Hold car off the ground, so it will not runaway when first
starts YOU WILL BREAK THE CONNECTING
• Turn on Radio and check the linkage before starting ROD!
engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt FAILURE TO NOT READ AND
out.
FOLLOW BREAK-IN ENGINE
Engine Break-in
• See Engine Page. INSTRUCTIONS WILL VOID
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake. WARRANTY!
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
CHECK RADIO SETTING,
Storing Car After Running
• Remove fuel from tank and fuel lines LINKAGE AND SET FAIL SAFE
• Turn off radio in car
• Put a few drops of after run in engine to keep it from BEFORE STARTING.
rusting.
The car is very fast
and will too easily hit someone.
RTR KITS - REQUIRED FOR OPERATION
THINGS NEEDED
AA Batteries ( 12 pcs )
Glow Fuel
20%
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
#91009 $5.95
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Grease
You need to get batteries for the radio transmitter and the car receiver packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline.,
Alkaline type batteries will work, but braking will be reduced and 30 minute life. The
best for car, is to use a 5 cell hump receiver pack for increased voltage and longer
life..
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell
type(600AE). This will give more run time. OFNA #10212 1000NiMh Hump Pack and
NiHm Battery Charger #10214
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will
over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007). Use plugs
without idle bar. Do NOT use plugs, like the MC-59 or OS-8
In your box you will find..
• #10163 - Bottle, spout top
• #10218 - Red “C” size glow heater
#10212 NiHm Hump Pack,
see charger 10214.
10214
Over-nite
Charger
MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe • Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This Precautions
kit is extremely fast, easily over 40MPH, and can seriously • This kit is not a toy. Always run car with a second
injure someone if you are not careful. person as a spotter and pitman.
Where to run car? • Hot Parts - The pipe, manifold, engine and head are very
• Any running area you choose must be dry. Do not run hot and will cause burns.
car near any water or wet dirt.
• Do not run on public streets. It is very easy to have the • Rotating Parts - Keep hands away from the drive train,
car run over or damaged by hitting the curb. wheels, and engine when engine is running.
• Do not operate car in tight confined places. The car is
very fast and will easily hit something. • Radio - Check batteries life before running the car. If
• Do not run near people or animals. radio does not have full control of the car with steering
and/or throttle/brake do not run until corrected. Failure to
• Due noise, you will want to consider the surrounding correct this will result in possible injury and damage to the
area when operating the car. car or property.
• Do not operate the car at night. You will not be able to
drive it without hitting something. • Glow fuel - Do leave the glow fuel unattended with the lid
• Do not operate the car indoors. Engine exhaust is not off. Fuel contains Methanol and Nitro Methane and is
healthy. flammable and poisonous.
Glow Fuel Store fuel in cool ventilated location. Refer the glow fuel
• Glow fuel is poisonous!
• Glow fuel is flammable! label for additional precautions.
• Do not leave in fuel bottle with lid off at any time.
• Do not use any fuel other than glow fuel in this engine. • Car Fuel tank - Never store fuel in car tank, it will ruin the
engine if left in tank.
First Time Starting the Engine
Caution! When starting engine make sure the following is • Always turn off the car BEFORE turning off radio.
observed.
• Set engine Master needle to 3 turns (rich setting) • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
• Do not do this alone, get an experienced friend to help at ISSUE.
first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on IF YOU DO NOT BREAK-IN ENGINE
receiver CORRECTLY, MAINLY AT LOW RPM,
• Hold car off the ground, so it will not runaway when first
starts YOU WILL BREAK THE CONNECTING
• Turn on Radio and check the linkage before starting ROD!
engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt FAILURE TO NOT READ AND
out.
FOLLOW BREAK-IN ENGINE
Engine Break-in
• See Engine Page. INSTRUCTIONS WILL VOID
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake. WARRANTY!
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
CHECK RADIO SETTING,
Storing Car After Running
• Remove fuel from tank and fuel lines LINKAGE AND SET FAIL SAFE
• Turn off radio in car
• Put a few drops of after run in engine to keep it from BEFORE STARTING.
rusting.
The car is very fast
and will too easily hit someone.
RTR KITS - REQUIRED FOR OPERATION
THINGS NEEDED
AA Batteries ( 12 pcs )
Glow Fuel
20%
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
#91009 $5.95
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Grease
You need to get batteries for the radio transmitter and the car receiver packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline.,
Alkaline type batteries will work, but braking will be reduced and 30 minute life. The
best for car, is to use a 5 cell hump receiver pack for increased voltage and longer
life..
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell
type(600AE). This will give more run time. OFNA #10212 1000NiMh Hump Pack and
NiHm Battery Charger #10214
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will
over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007). Use plugs
without idle bar. Do NOT use plugs, like the MC-59 or OS-8
In your box you will find..
• #10163 - Bottle, spout top
• #10218 - Red “C” size glow heater
#10212 NiHm Hump Pack,
see charger 10214.
10214
Over-nite
Charger
THINGS NEED BESIDES THE KIT
RADIO CONTROL UNIT
12V Battery for Starter Box
(must have)
Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)
AA Batteries ( 12 pcs ) for radio
Note: Carefully read the instruction manual of your
2 channel radio controller before using.
Radio must be set at neutral position
before installing in the kit.
SEQUENCE TO SET NEUTRAL
Note: Pro kit does not include engine!
Glow Fuel
20%
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the
battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral,
servo horns must be in neutral as will.
*Adjustment can be made by re-
installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
Retract the antenna. (Transmitter)
1111
12
13
NON-RTR OR PRO KITS - REQUIRED FOR OPERATION
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
SUITABLE SERVO SIZE
29mm - 42mm
15mm - 21mm
36mm-41mm
3.5 cc (21 Class) ENGINE
REAR EXHAUST
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
TOOLS NOT INCLUDED IN KIT
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Masking Tape
Paints
Grease
Brush
More Optional Parts . . .
#10211 NiHm Battery Flat
Pack .. $29.95
# 10214 NiHm Battery Pack
Charger.. $7.95
# 51007 OFNA/Picoo Glow
Plug .. $4.95
INCLUDED WITH KIT
Shock Oil
1.5mm
Hex Wrench
Grease Box
2.5mm
Hex Wrench
3mm
Hex Wrench
5mm
Hex Wrench
7mm and 5.5mm
Hex Wrench
OFNA/Picco
O-1 bp
#51217
40003
DIFF. CASE
PLASTIC PARTS
40017
GEAR BOX PLASTIC PARTS
13
2
PLASTIC PARTS
40015
ARM HOLDER PLASTIC PARTS
40027
WING SUPPORT PLASTIC PARTS 40013 & 40048
FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
36901
Front Knuckles, Pivot Ball
40202
Front and Rear Lower Arms.
31304
Rear Hub,
Pivot Ball
40094
Front Upper
MBX Arm
THINGS NEED BESIDES THE KIT
RADIO CONTROL UNIT
12V Battery for Starter Box
(must have)
Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)
AA Batteries ( 12 pcs ) for radio
Note: Carefully read the instruction manual of your
2 channel radio controller before using.
Radio must be set at neutral position
before installing in the kit.
SEQUENCE TO SET NEUTRAL
Note: Pro kit does not include engine!
Glow Fuel
20%
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the
battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral,
servo horns must be in neutral as will.
*Adjustment can be made by re-
installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
Retract the antenna. (Transmitter)
1111
12
13
NON-RTR OR PRO KITS - REQUIRED FOR OPERATION
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
SUITABLE SERVO SIZE
29mm - 42mm
15mm - 21mm
36mm-41mm
3.5 cc (21 Class) ENGINE
REAR EXHAUST
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
TOOLS NOT INCLUDED IN KIT
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Masking Tape
Paints
Grease
Brush
More Optional Parts . . .
#10211 NiHm Battery Flat
Pack .. $29.95
# 10214 NiHm Battery Pack
Charger.. $7.95
# 51007 OFNA/Picoo Glow
Plug .. $4.95
INCLUDED WITH KIT
Shock Oil
1.5mm
Hex Wrench
Grease Box
2.5mm
Hex Wrench
3mm
Hex Wrench
5mm
Hex Wrench
7mm and 5.5mm
Hex Wrench
OFNA/Picco
O-1 bp
#51217
40003
DIFF. CASE
PLASTIC PARTS
40017
GEAR BOX PLASTIC PARTS
13
2
PLASTIC PARTS
40015
ARM HOLDER PLASTIC PARTS
40027
WING SUPPORT PLASTIC PARTS 40013 & 40048
FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
36901
Front Knuckles, Pivot Ball
40202
Front and Rear Lower Arms.
31304
Rear Hub,
Pivot Ball
40094
Front Upper
MBX Arm
PLASTIC PARTS
40031
SERVO SAVER PLASTIC PARTS 40047
RECEIVER BOX PLASTIC PARTS
40040
CENTER DIFF. MOUNT PLASTIC PARTS
40046
STONE GUARD PLASTIC PARTS
40018/40029
CHASSIS BRACE PLASTIC PARTS
40056
SHOCK ABSORBER PLASTIC PARTS
A
B
C
CHECKING ENGINE THROTTLE
* Insert into transmitter.
1. Insert AA batteries into
transmitter (8 Pcs).
2.Turn on transmitter.
3.Turn on receiver.
4.Center throttle trims as
shown .
ABC
1. Pull Full Throttle. 1. Push trigger to full
brake position.
2. Adjust alum. Stopper to
increase or decrease
the brake.
Idle Position (A)
Brake (C)
Full Throttle (B)
* Align throttle servo same
as shown.
ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM
3X3mm
Set Screw 3X3mm
Set Screw
3X3mm
Set Screw
Plastic Collar
* Take the plastic collar
from brake system plastic
parts.
Throttle
Spring
#10300
Alum.Stopper
#10300
Alum.Stopper
* Snap On.
#30530
Plastic Throttle
Ball Joint
2mm Rod
Fuel
Tube
( 6mm )
Idle Position
Brake
Full Throttle
* Align throttle servo same
as shown.
A
B
C
• Full brake arm position.
Spring compresses
forward and brake rods
pull brake levers.
• Full throttle arm position.
Spring rod pulls throttle
barrel open and brake
rods release pressure on
brake cams.
IMPORTANT
CHECK RADIO THROTTLE
AND STEERING SWITCHES
BEFORE RUNNING CAR
#30800
Plastic Throttle
kit
Note:
Battery life is short when using Alkaline batteries. For safety, we recommend using
Alkaline batteries for only 30 minutes before testing.. Battery strength affects braking
power and radio range. If voltage drops while running the car, you will loose control and
destroy your car! This is NOT covered under warranty.
To increase run time, upgrade receiver battery to a 5-cell hump pack. But, the most
important step you can make, “is to always use fully charged or fresh batteries when
running your car”. Another choice is to use OFNA #10196 2000 mAh NiMh AA batteries in
car and radio.
PLASTIC PARTS
40031
SERVO SAVER PLASTIC PARTS 40047
RECEIVER BOX PLASTIC PARTS
40040
CENTER DIFF. MOUNT PLASTIC PARTS
40046
STONE GUARD PLASTIC PARTS
40018/40029
CHASSIS BRACE PLASTIC PARTS
40056
SHOCK ABSORBER PLASTIC PARTS
A
B
C
CHECKING ENGINE THROTTLE
* Insert into transmitter.
1. Insert AA batteries into
transmitter (8 Pcs).
2.Turn on transmitter.
3.Turn on receiver.
4.Center throttle trims as
shown .
ABC
1. Pull Full Throttle. 1. Push trigger to full
brake position.
2. Adjust alum. Stopper to
increase or decrease
the brake.
Idle Position (A)
Brake (C)
Full Throttle (B)
* Align throttle servo same
as shown.
ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM
3X3mm
Set Screw 3X3mm
Set Screw
3X3mm
Set Screw
Plastic Collar
* Take the plastic collar
from brake system plastic
parts.
Throttle
Spring
#10300
Alum.Stopper
#10300
Alum.Stopper
* Snap On.
#30530
Plastic Throttle
Ball Joint
2mm Rod
Fuel
Tube
( 6mm )
Idle Position
Brake
Full Throttle
* Align throttle servo same
as shown.
A
B
C
• Full brake arm position.
Spring compresses
forward and brake rods
pull brake levers.
• Full throttle arm position.
Spring rod pulls throttle
barrel open and brake
rods release pressure on
brake cams.
IMPORTANT
CHECK RADIO THROTTLE
AND STEERING SWITCHES
BEFORE RUNNING CAR
#30800
Plastic Throttle
kit
Note:
Battery life is short when using Alkaline batteries. For safety, we recommend using
Alkaline batteries for only 30 minutes before testing.. Battery strength affects braking
power and radio range. If voltage drops while running the car, you will loose control and
destroy your car! This is NOT covered under warranty.
To increase run time, upgrade receiver battery to a 5-cell hump pack. But, the most
important step you can make, “is to always use fully charged or fresh batteries when
running your car”. Another choice is to use OFNA #10196 2000 mAh NiMh AA batteries in
car and radio.
4x4mm
Set Screw
4x4mm
Set Screw
ASSEMBLY OF THE DIFFERENTIAL CASE
40006
Cap Joint
40006
Cap Joint
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40009
P6 O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40003
Diff. Case
40003
Diff. Case
40005
Break
Cap Joint
40005
Break
Cap Joint
(Builds one differential for Center)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
(Builds one differential for Center)
40002
41T Large
Bevel Gear
40002
41T Large
Bevel Gear
OPTION:
49032
43T Large
Bevel Gear
(must use 13t pinion)
40011
Diff. Gasket
40011
Diff. Gasket
3x12mm
Flat Head
Tapping Screw
3x12mm
Flat Head
Tapping Screw
40001
47T
Spur Gear
40001
47T
Spur Gear
*Use 6x15mm washer
to adjust the gear mesh.
*Use 6x15mm washer
to adjust the gear mesh.
Note: It is very important to add
or remove the #30779 washer if
the gear mesh is too tight or
too lose.
( Builds two differentials for front and rear.)
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer 30773
4mm
Cross pin
30773
4mm
Cross pin
* Apply diff. gear grease to the
differential during assembly.
* Fill the diff. the case to
approx 70% with grease.
ASSEMBLY OF THE DIFFERENTIAL GEAR
OPTION: #49001 HD STEEL GEAR SET,
INSIDE DIFF.
OPTION:
#49016 SPUR GEAR 50T
#49031 SPUR GEAR 50T, HD SPECIAL
ASSEMBLY OF THE FRONT GEAR BOX
ASSEMBLY OF THE FRONT ARMS HOLDER
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40024
13x16x0.2mm
Shim
40021
14T Small
Bevel Gear..............1
40021
14TSmall
Bevel Gear
40017
Gear Box
40017
Gear Box
4x15mm
Tapping Screw
(Small Head)
4x45mm
Tapping Screw
(Small Head)
40022
Front Lower Arm
Holder (Front)
90026
5x5mm
Set Screw
36730
Cap Joint
36730
Cap Joint................................1
40015
Front Lower arm
Holder (Rear/Plastic)
40015
Front Upper arm
Holder (Rear/Plastic)
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw.......................4
4x15mm
Tapping Screw........................2
4x45mm
Tapping Screw........................2
90026
5x5mm
Set Screw......1
Screw
Cement
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
OPTION: #49002 CNC 7075
FRONT LOWER ARM HOLDER
OPTION: #49012 PINION GEAR
13TOOTH
MISC. SCREW BAG
40067
Use shims to adjust gear
mesh.
4x4mm
Set Screw
4x4mm
Set Screw
ASSEMBLY OF THE DIFFERENTIAL CASE
40006
Cap Joint
40006
Cap Joint
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40009
P6 O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40009
P6
O-Ring
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40012
6x15mm
Washer
40003
Diff. Case
40003
Diff. Case
40005
Break
Cap Joint
40005
Break
Cap Joint
(Builds one differential for Center)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
(Builds one differential for Center)
40002
41T Large
Bevel Gear
40002
41T Large
Bevel Gear
OPTION:
49032
43T Large
Bevel Gear
(must use 13t pinion)
40011
Diff. Gasket
40011
Diff. Gasket
3x12mm
Flat Head
Tapping Screw
3x12mm
Flat Head
Tapping Screw
40001
47T
Spur Gear
40001
47T
Spur Gear
*Use 6x15mm washer
to adjust the gear mesh.
*Use 6x15mm washer
to adjust the gear mesh.
Note: It is very important to add
or remove the #30779 washer if
the gear mesh is too tight or
too lose.
( Builds two differentials for front and rear.)
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer
30779
4 x 10mm
washer 30773
4mm
Cross pin
30773
4mm
Cross pin
* Apply diff. gear grease to the
differential during assembly.
* Fill the diff. the case to
approx 70% with grease.
ASSEMBLY OF THE DIFFERENTIAL GEAR
OPTION: #49001 HD STEEL GEAR SET,
INSIDE DIFF.
OPTION:
#49016 SPUR GEAR 50T
#49031 SPUR GEAR 50T, HD SPECIAL
ASSEMBLY OF THE FRONT GEAR BOX
ASSEMBLY OF THE FRONT ARMS HOLDER
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40024
13x16x0.2mm
Shim
40021
14T Small
Bevel Gear..............1
40021
14TSmall
Bevel Gear
40017
Gear Box
40017
Gear Box
4x15mm
Tapping Screw
(Small Head)
4x45mm
Tapping Screw
(Small Head)
40022
Front Lower Arm
Holder (Front)
90026
5x5mm
Set Screw
36730
Cap Joint
36730
Cap Joint................................1
40015
Front Lower arm
Holder (Rear/Plastic)
40015
Front Upper arm
Holder (Rear/Plastic)
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw.......................4
4x15mm
Tapping Screw........................2
4x45mm
Tapping Screw........................2
90026
5x5mm
Set Screw......1
Screw
Cement
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
OPTION: #49002 CNC 7075
FRONT LOWER ARM HOLDER
OPTION: #49012 PINION GEAR
13TOOTH
MISC. SCREW BAG
40067
Use shims to adjust gear
mesh.
40067
M3x12
TP Screw
40067
M4x15
TP Screw
35314
4mm
Nylon Nut
ASSEMBLY OF THE FRONT SHOCK TOWER OPT: 49003
CNC 7075 Alum. Shock Tower
49037
Front
Shock Tower, Orange
ASSEMBLY OF THE FRONT PIVOT
BALL KNUCKLE ARM
36901
Ball Type
Knuckle Arms
( Right and Left Side)
* Note the "R" mark
is for righthand side.
* Adjust alum. nut to
keep steering ball
smooth.
Assembly of the right and left hand side
are the same.
Assembly of the right and left hand side
are the same.
* Use 5mm
hex wrench.
36904
14mm
Alum. Nut 36905
Steering Ball
Washer
36903
14mm
Steering Ball 36052
CVD
Universal Joint
36053
8x16mm
Ball Bearing
36053
8x16mm
Ball Bearing
ASSEMBLY OF THE FRONT KNUCKLE ARM
INTO FRONT ARMS
4X10mm
set screw 36870
4x4mm
Set Screw
* A 4x10mm set screw is used
to adjust the ride-height.
* Use a 2.5mm
hex wrench.
40245
Orange
Wheel Hub
( Alum.)
36055
2.5x17mm
Pin
3mm
3.5mm
40202
Front Lower
MBX Arm
40094
Front Upper
MBX Arm
ASSEMBLY OF THE FRONT SUSPENSION ARMS
40023
Lower Arm Shaft (4mm)
90021
3mm
E-Ring
90021
3mm
E-Ring
90020
2.5mm
E-Ring
90020
2.5mm
E-Ring
36170
3mm
Arm Shaft
* Insert the drive shaft into the
cap joint before assembly.
Assembly of the right and left hand side
are the same.
40067
M3x12
TP Screw
40067
M4x15
TP Screw
35314
4mm
Nylon Nut
ASSEMBLY OF THE FRONT SHOCK TOWER OPT: 49003
CNC 7075 Alum. Shock Tower
49037
Front
Shock Tower, Orange
ASSEMBLY OF THE FRONT PIVOT
BALL KNUCKLE ARM
36901
Ball Type
Knuckle Arms
( Right and Left Side)
* Note the "R" mark
is for righthand side.
* Adjust alum. nut to
keep steering ball
smooth.
Assembly of the right and left hand side
are the same.
Assembly of the right and left hand side
are the same.
* Use 5mm
hex wrench.
36904
14mm
Alum. Nut 36905
Steering Ball
Washer
36903
14mm
Steering Ball 36052
CVD
Universal Joint
36053
8x16mm
Ball Bearing
36053
8x16mm
Ball Bearing
ASSEMBLY OF THE FRONT KNUCKLE ARM
INTO FRONT ARMS
4X10mm
set screw 36870
4x4mm
Set Screw
* A 4x10mm set screw is used
to adjust the ride-height.
* Use a 2.5mm
hex wrench.
40245
Orange
Wheel Hub
( Alum.)
36055
2.5x17mm
Pin
3mm
3.5mm
40202
Front Lower
MBX Arm
40094
Front Upper
MBX Arm
ASSEMBLY OF THE FRONT SUSPENSION ARMS
40023
Lower Arm Shaft (4mm)
90021
3mm
E-Ring
90021
3mm
E-Ring
90020
2.5mm
E-Ring
90020
2.5mm
E-Ring
36170
3mm
Arm Shaft
* Insert the drive shaft into the
cap joint before assembly.
Assembly of the right and left hand side
are the same.
ASSEMBLY OF THE REAR GEAR BOX
4X16mm
Tapping Screw
(Small Head)
4X15mm
Tapping Screw
(Small Head)
4X10mm
Tapping Screw
(Small Head)
4X45mm
Flat Head
Tapping Screw
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
40024
13x16x0.2mm
Shim
40021
14T Pinion
Gear
* Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
1.5
2
3
90026
5x5mm
Set Screw
36730
Cap Joint
40025
Rear
Lower Arm Holder
( 0 Degree)
35314
4mm
Nylon Nut
4 x 15mm
Tapping Screw
( Small Head )..........6
35314
4mm
Nylon Nut..............2
90026
5 x 5mm
Set Screw..............1
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40021
14T Pinion
Bevel Gear..............1
36730
Cap Joint.................1
4 x 20mm
Flat Head
Tapping Screw..........2
40027
Wing Stay
Mount
40015
Rear arm Holder
Screw
Cement
OPTION: #49007 REAR LOWER
ANTI-SQUAT HOLDERS - 1.5; 2.0;
3.0 DEGREES.
OPTION: #49012 PINION GEAR
13TOOTH
3X12mm
Tapping Screw
* Insert the front bumper
before assembly.
30701
3x8mm
Set Screw
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
3x10mm
Flat Head
Tapping Screw 3x3mm
Set Screw
30701
3x3
Set Screw
30701
3x3
Set Screw
40019
Stabilizer
3x10mm
Flat Head
Tapping Screw
40018
Stabilizer
Mount Plastic
40013
Front
Bumper
40064
Chassis
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
30341
Stabilizer Ball
30341
Stabilizer Ball..........2
ASSEMBLY OF THE FRONT STABILIZER
3 x 10mm
Flat Head
Tapping Screw........2
4 x 16mm
Flat Head
Tapping Screw..........4
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
30701
3 x 3mm
Set Screw..............4
40068
Misc. Hardware
Bag, 9.5 RTR
40068
Misc. Hardware Bag
9.5 RTR
ASSEMBLY OF THE REAR GEAR BOX
4X16mm
Tapping Screw
(Small Head)
4X15mm
Tapping Screw
(Small Head)
4X10mm
Tapping Screw
(Small Head)
4X45mm
Flat Head
Tapping Screw
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
40024
13x16x0.2mm
Shim
40021
14T Pinion
Gear
* Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
1.5
2
3
90026
5x5mm
Set Screw
36730
Cap Joint
40025
Rear
Lower Arm Holder
( 0 Degree)
35314
4mm
Nylon Nut
4 x 15mm
Tapping Screw
( Small Head )..........6
35314
4mm
Nylon Nut..............2
90026
5 x 5mm
Set Screw..............1
36053
8X16mm
Ball bearing....4
40024
13x16x0.2mm
Shim..............2
40021
14T Pinion
Bevel Gear..............1
36730
Cap Joint.................1
4 x 20mm
Flat Head
Tapping Screw..........2
40027
Wing Stay
Mount
40015
Rear arm Holder
Screw
Cement
OPTION: #49007 REAR LOWER
ANTI-SQUAT HOLDERS - 1.5; 2.0;
3.0 DEGREES.
OPTION: #49012 PINION GEAR
13TOOTH
3X12mm
Tapping Screw
* Insert the front bumper
before assembly.
30701
3x8mm
Set Screw
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
3x10mm
Flat Head
Tapping Screw 3x3mm
Set Screw
30701
3x3
Set Screw
30701
3x3
Set Screw
40019
Stabilizer
3x10mm
Flat Head
Tapping Screw
40018
Stabilizer
Mount Plastic
40013
Front
Bumper
40064
Chassis
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
30341
Stabilizer Ball
30341
Stabilizer Ball..........2
ASSEMBLY OF THE FRONT STABILIZER
3 x 10mm
Flat Head
Tapping Screw........2
4 x 16mm
Flat Head
Tapping Screw..........4
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
30701
3 x 3mm
Set Screw..............4
40068
Misc. Hardware
Bag, 9.5 RTR
40068
Misc. Hardware Bag
9.5 RTR
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE WING STAY
40027
Rear
Body Mount
( Take the plastic part from #40027Rear Win Stay Set. )
49038
Rear
Shock Tower, Orange
3x12mm
Tapping Screw
35313
3mm
Nylon Nut
40027
Wing Mount
40027
Wing Mount
*Insert the 3mm nylon nut
before assembly.
3x20
Tapping Screw
3x20
Tapping Screw
40027
Wing Stay
( Left )
40027
Wing Stay
( Right )
40027
Wing Mount
40027
Wing Mount
40027
Wing Stay
Post
3x12mm
Tapping Screw
4x15mm
Tapping Screw
( Small Head )
4x15mm
Tapping Screw
( Small Head )
3 x 20mm
Tapping Screw............6
4 x 15mm
Tapping Screw
( Small Head )............2
4 x 15mm
Tapping Screw
( Small Head )............4
3mm
Nylon Nut........2
3 x 12mm
Tapping Screw........3
OPTION: #49004 CNC 7075
REAR SHOCK TOWER
OPTION: #49043 CNC ALIM.
POSTS, WING MOUNT, ORANGE
ASSEMBLY OF THE REAR UPPER ARMS
40023
Lower Arm Shaft
90021
3mm
E-Ring
90021
3mm
E-Ring
36860
5x40mm
Turnbuckle
36860
5x40mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
(Make two upper arms for left an right hand side. )
4 x 10 mm
Set Screw...........2
90026
5 x 5mm
Set Screw............2
3 mm
E-Ring...............4
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
16mm
90026
5mm
Set Screw
40245
8mm
Wheel Hub
36055
2.5x17mm
Pin
* Make sure the pivot ball
move smooth.
36081
Rear Wheel
Axle Shaft
31304
Pivot Ball
rear Hub
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
31305
Spacer Washer
31305
Spacer Washer
31307
11mm
Pivot Ball
31306
12mm
Hex Nut
5mm
Hex Wrench
ASSEMBLY OF THE PIVOT BALL REAR HUB
ASSEMBLY OF THE REAR SUSPENSION INTO
GEAR BOX
Assembly of the right and left hand side
are the same.
* A 4 x 10mm set screw is used
to adjust the ride height.
36870
4mm
Set screw
40202
Rear Lower Arm
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE WING STAY
40027
Rear
Body Mount
( Take the plastic part from #40027Rear Win Stay Set. )
49038
Rear
Shock Tower, Orange
3x12mm
Tapping Screw
35313
3mm
Nylon Nut
40027
Wing Mount
40027
Wing Mount
*Insert the 3mm nylon nut
before assembly.
3x20
Tapping Screw
3x20
Tapping Screw
40027
Wing Stay
( Left )
40027
Wing Stay
( Right )
40027
Wing Mount
40027
Wing Mount
40027
Wing Stay
Post
3x12mm
Tapping Screw
4x15mm
Tapping Screw
( Small Head )
4x15mm
Tapping Screw
( Small Head )
3 x 20mm
Tapping Screw............6
4 x 15mm
Tapping Screw
( Small Head )............2
4 x 15mm
Tapping Screw
( Small Head )............4
3mm
Nylon Nut........2
3 x 12mm
Tapping Screw........3
OPTION: #49004 CNC 7075
REAR SHOCK TOWER
OPTION: #49043 CNC ALIM.
POSTS, WING MOUNT, ORANGE
ASSEMBLY OF THE REAR UPPER ARMS
40023
Lower Arm Shaft
90021
3mm
E-Ring
90021
3mm
E-Ring
36860
5x40mm
Turnbuckle
36860
5x40mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
(Make two upper arms for left an right hand side. )
4 x 10 mm
Set Screw...........2
90026
5 x 5mm
Set Screw............2
3 mm
E-Ring...............4
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
40018
Upper Arm
Plastic Rod End
16mm
90026
5mm
Set Screw
40245
8mm
Wheel Hub
36055
2.5x17mm
Pin
* Make sure the pivot ball
move smooth.
36081
Rear Wheel
Axle Shaft
31304
Pivot Ball
rear Hub
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
31305
Spacer Washer
31305
Spacer Washer
31307
11mm
Pivot Ball
31306
12mm
Hex Nut
5mm
Hex Wrench
ASSEMBLY OF THE PIVOT BALL REAR HUB
ASSEMBLY OF THE REAR SUSPENSION INTO
GEAR BOX
Assembly of the right and left hand side
are the same.
* A 4 x 10mm set screw is used
to adjust the ride height.
36870
4mm
Set screw
40202
Rear Lower Arm
ASSEMBLY OF THE REAR ANTI-ROD BAR
3x3
Set Screw
3x3
Set Screw
3x3
Set Screw
3X10mm
Flat Head
Screw
3X10mm
Flat Head
Screw
40019
Stabilizer
40018
Stabilizer
Mount Plastic
30341
Stabilizer Ball..........2
3 x 10mm
Flat Head
Tapping Screw........2
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
30701
3 x 3mm
Set Screw..............2
3 x 20mm
Cap Screw..........2
90019
3 X 25mm
Cap Screw.........2
35313
M3
Nylon Nut..........2
30701
3 x 3mm
Set Screw..........2
30701
3 x 8mm
et Screw..........2.
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
30341
Stabilizer Ball
3x8mm
Set Screw
35313
3mm
Nylon Nut
3mm
Nylon Nut
3 x 25mm
Cap Screw
3 x 20mm
Cap Screw
36110
Rear
Driver Shaft
* Insert rear driver shaft
before assembly.
Rear Upper Arm
Assembly
Assembly of the right and left hand side
are the same.
40068
4 x 16mm
Flat Head
Tapping Screw..........4
4 x 16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE REAR GEAR BOX ONTO CHASSIS
40064
Chassis
ASSEMBLY OF THE SERVO SAVER
M3 Nut
* Put the 3mm
nut before assembly.
40031
Servo Saver
Horn A 40095
Servo Saver
Connecting Plate,
Orange
6x10mm
Plastic
Bushing
6x10mm
Plastic
Bushing
Servo Saver
Horn C
4x8mm
Plastic flange
Bushing
40037
Steering Plate
Hex Screw
40037
Steering Plate
Hex Screw
40035
Servo Saver
Alum. Axle
Tube
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
40034
Servo Saver
Spring Tension
Adjuster
40036
servo Saver
Post 40036
Servo Saver
Post
40074
6x10mm
Ball bearing
35313
M3 Nut..........1
4x10mm
Screw..........2
* Take the 4x8mm Plastic Flange bushing
and Plastic Bushing from servo saver plastic
parts tree
OPTION: #49014 CNC BALL
BEARING AXLE TUBE
Option:
40073
4x8mm
Ball bearing
flange
40037
Steering Plat
Hex Screw....... 2
Option:
40074
6x10mm
Ball bearing
40068
Misc. Screw and
Hardware Bag
30702
Misc. Cap Screws,
Hex, Bag
ASSEMBLY OF THE REAR ANTI-ROD BAR
3x3
Set Screw
3x3
Set Screw
3x3
Set Screw
3X10mm
Flat Head
Screw
3X10mm
Flat Head
Screw
40019
Stabilizer
40018
Stabilizer
Mount Plastic
30341
Stabilizer Ball..........2
3 x 10mm
Flat Head
Tapping Screw........2
3 x 20mm
Screw ......................2
3 x 12mm
Tapping Screw..........1
30701
3 x 3mm
Set Screw..............2
3 x 20mm
Cap Screw..........2
90019
3 X 25mm
Cap Screw.........2
35313
M3
Nylon Nut..........2
30701
3 x 3mm
Set Screw..........2
30701
3 x 8mm
et Screw..........2.
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
30401
6mm
Ball End
3x20mm
Screw
3x20mm
Screw
30341
Stabilizer Ball
3x8mm
Set Screw
35313
3mm
Nylon Nut
3mm
Nylon Nut
3 x 25mm
Cap Screw
3 x 20mm
Cap Screw
36110
Rear
Driver Shaft
* Insert rear driver shaft
before assembly.
Rear Upper Arm
Assembly
Assembly of the right and left hand side
are the same.
40068
4 x 16mm
Flat Head
Tapping Screw..........4
4 x 16mm
Flat Head
Tapping Screw
4 x 16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE REAR GEAR BOX ONTO CHASSIS
40064
Chassis
ASSEMBLY OF THE SERVO SAVER
M3 Nut
* Put the 3mm
nut before assembly.
40031
Servo Saver
Horn A 40095
Servo Saver
Connecting Plate,
Orange
6x10mm
Plastic
Bushing
6x10mm
Plastic
Bushing
Servo Saver
Horn C
4x8mm
Plastic flange
Bushing
40037
Steering Plate
Hex Screw
40037
Steering Plate
Hex Screw
40035
Servo Saver
Alum. Axle
Tube
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
40034
Servo Saver
Spring Tension
Adjuster
40036
servo Saver
Post 40036
Servo Saver
Post
40074
6x10mm
Ball bearing
35313
M3 Nut..........1
4x10mm
Screw..........2
* Take the 4x8mm Plastic Flange bushing
and Plastic Bushing from servo saver plastic
parts tree
OPTION: #49014 CNC BALL
BEARING AXLE TUBE
Option:
40073
4x8mm
Ball bearing
flange
40037
Steering Plat
Hex Screw....... 2
Option:
40074
6x10mm
Ball bearing
40068
Misc. Screw and
Hardware Bag
30702
Misc. Cap Screws,
Hex, Bag
4x10mm
Flat Head
Screw
4x10mm
Screw
4x15mm
Tapping Screw
40027
Front Body
Post
3x12mm
Screw
* Assembly the front body post
before assembly the Front Plate.
40095
Front Plat,
Orange
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS
36790
4x46mm
Turnbuckle
36790
4x46mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
36700
Steering
Ball End
36700
Steering
Ball End
36700
Steering
Ball End
35313
3mm
Nylon Nut
40039
3mm Tapper
Washer(Alum.)
40039
3mm Tapper
Washer(Alum.)
3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw
ASSEMBLY OF THE FRONT STEERING ROD
4x10mm
Screw..........2
3 x 12mm
Tapping Screw..........1
35313
M3
Nylon Nut..........2
40039
M3
Taper Cone..........4
4 x 15mm
Tapping Screw
( Small Head )............2
3 x 15mm
Flat Head
Screw..........4
4 x 10mm
Flat Head Screw..........2
Assembly of the right and left hand side
are the same.
0 10 20 30 40 50
mm
* Anticlockwise mark.
29mm
* Made two steering rods for left and righthand side.
OPTION:
49005 -CNC 7075 Alum. Front Plate
49019 - Graphite Front PLate
* Take off the double sided paper
before assembly.
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side.
36660
Brake Pad
36661
Brake Pad
linings
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40045
Brake Pad
Adjustment Screw
40045
Brake Pad
Adjustment Screw
40043
Center Diff. Mount
Post
40040
Break Disc
Holder
40040
Brake Disk
Holder 40040
Brake Disc
Holder
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40046
Brake Pad Screw...........4
40044
Brake Pad
Spring.........8
40043
Center Diff. Mount
Post...........................4
Large
Hole
Small
Hole
Assembly the brake disc holder
in the direction shown.
*Towards
the front.
*Towards
the Rear.
Small hole to the
Outside.
OPTION: #49030 CNC 7075 SPLIT
CENTER DIFF MOUNT.
4x10mm
Flat Head
Screw
4x10mm
Screw
4x15mm
Tapping Screw
40027
Front Body
Post
3x12mm
Screw
* Assembly the front body post
before assembly the Front Plate.
40095
Front Plat,
Orange
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS
36790
4x46mm
Turnbuckle
36790
4x46mm
Turnbuckle
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
36700
Steering
Ball End
36700
Steering
Ball End
36700
Steering
Ball End
35313
3mm
Nylon Nut
40039
3mm Tapper
Washer(Alum.)
40039
3mm Tapper
Washer(Alum.)
3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw
ASSEMBLY OF THE FRONT STEERING ROD
4x10mm
Screw..........2
3 x 12mm
Tapping Screw..........1
35313
M3
Nylon Nut..........2
40039
M3
Taper Cone..........4
4 x 15mm
Tapping Screw
( Small Head )............2
3 x 15mm
Flat Head
Screw..........4
4 x 10mm
Flat Head Screw..........2
Assembly of the right and left hand side
are the same.
0 10 20 30 40 50
mm
* Anticlockwise mark.
29mm
* Made two steering rods for left and righthand side.
OPTION:
49005 -CNC 7075 Alum. Front Plate
49019 - Graphite Front PLate
* Take off the double sided paper
before assembly.
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side.
36660
Brake Pad
36661
Brake Pad
linings
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40045
Brake Pad
Adjustment Screw
40045
Brake Pad
Adjustment Screw
40043
Center Diff. Mount
Post
40040
Break Disc
Holder
40040
Brake Disk
Holder 40040
Brake Disc
Holder
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40046
Brake Pad Screw...........4
40044
Brake Pad
Spring.........8
40043
Center Diff. Mount
Post...........................4
Large
Hole
Small
Hole
Assembly the brake disc holder
in the direction shown.
*Towards
the front.
*Towards
the Rear.
Small hole to the
Outside.
OPTION: #49030 CNC 7075 SPLIT
CENTER DIFF MOUNT.
40042
Brake Disk 40042
Brake Disk
40042
Brake Disk 40042
Brake Disk
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
Center Diff. Assembly
3x3mm
Set Screw
3x3mm
Set Screw
3x10mm
Screw
40031
Fuel Overflow
Proof Plate
30213
Brake Cam
30211
Plastic
Bushing
Option
30212
5X8mm
Ball Bearing
40096
Center Diff.
Plate, Orange
30171
Brake Lever
30171
Brake Lever..........2
30171
Brake Lever
3x10mm
Screw
4x10mm
Screw..........4
3 x 3mm
Set Screw..............2
Put the front brake lever as
Shown.
OPTION: #49008 GRAPHITE
BRAKE DISKS, 2PCS.
OPTION: #49018 GRAPHITE
TOP CENTER PLATE
Screw
Cement
Screw
Cement
40028
Center Drive
Shaft (93mm)
40028
Center Drive
Shaft (93mm)
4x12mm
Flat Head
Screw
4x12mm
Flat Head
Screw
3x25mm
Cap Screw
35313
3mm
Nylon Nut
40018
Center Chassis
Brace
( Rear ) 40018
Center Chassis
Brace
( Front )
3x12mm
Screw
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
2.6x10mm
Flat Head
Tapping Screw
2.6x10mm
Flat Head
Tapping Screw
35313
3mm
Nylon Nut........1
3 x 12mm
Tapping Screw........3
3 X 25mm
Cap Screw.........1
4 x 12mm
Flat Head Screw..........2
4 x 16mm
Flat Head
Tapping Screw..........4
ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS
ASSEMBLY OF THE STIFFENER
OPTION:
49015- CNC Alum. Chassis Brace,
Front and Rear
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

Ofna Racing 9.5 MBX User manual

Brand
Ofna Racing
Model
9.5 MBX
Category
Remote controlled toys
Type
User manual

Ofna Racing 9.5 MBX is an unparalleled nitro-powered, off-road vehicle offering thrilling speeds exceeding 40 mph. It boasts a robust chassis with adjustable features for precision handling. The vehicle requires a 20% nitro glow fuel and runs best with OFNA/Picco Long Glow Plugs. Moreover, it necessitates batteries for the transmitter and receiver packs. To ensure safety, always have a second person present as a spotter and pitman.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents