ABB M2302 User manual

Category
Gateways/controllers
Type
User manual

This manual is also suitable for

VER:1.1 25.09.2015
ABB-Welcome
Pos: 2 /DinA4 - A nleitungen Onlin e/Inhalt/KNX/D oorEntry/832 20-AP-xxx/Ti telblatt - 83 220-AP-xxx - ABB @ 19\ mod_1323249 806476_15.doc x @ 111084 @ @ 1
M2302
Gateway
=== Ende der List e für Textmarke Cover ===
|
2
Pos: 4 /Busch-Ja eger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/In haltsverzeichnis ( --> Für alle Dokumente <--)/Inhalts verzeichnis @ 19\mod_1320 649044386_1 5.docx @ 109653 @ @ 1
1 Safety ............................................................................................................ 3
2 Intended use .................................................................................................. 3
3 Environment .................................................................................................. 3
3.1 ABB devices ................................................................................. 3
4 Operation ....................................................................................................... 5
4.1 Control elements .......................................................................... 5
4.2 Operating modes .......................................................................... 6
4.2.1 Building gateway .......................................................................... 6
4.2.2 Floor gateway ............................................................................... 8
4.2.3 Apartment gateway ..................................................................... 12
4.2.4 Additional power supply mode .................................................... 15
4.2.5 Line amplifier .............................................................................. 18
5 Technical data ............................................................................................. 20
6 Mounting/Installation .................................................................................... 21
6.1 Requirements for the electrician ................................................. 21
6.2 General installation instructions .................................................. 22
6.3 Mounting ..................................................................................... 22
=== Ende der List e für Textmarke TOC ===
Safety
|
3
Pos: 6 /Busch-Ja eger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/Übers chriften (--> Für alle Dokum ente <--)/1. Ebene/S - T/Sicherheit @ 18\mod_13 02612791790 _15.docx @ 10 3357 @ 1 @ 1
1 Safety
Pos: 7 /Busch-Ja eger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/Sich erheit (--> Für alle Doku mente <--)/Warnhin weise/Sicherheit - 2 30 V @ 18\m od_1302606816 750_15.docx @ 103308 @ @ 1
Warning
Electric voltage!
Risk of death and fire due to electrical voltage of 100-240 V.
Work on the 100-240V supply system may only be performed by
authorized electricians!
Disconnect the main power supply prior to installation and/or
disassembly!
Pos: 8 /Busch-Ja eger (Neustru ktur)/Modul-Str uktur/Online-Doku mentation/Übers chriften (--> Für alle Dokum ente <--)/1. Ebene/A - F/Bestim mungsgemäßer Gebrauch @ 18\mo d_13027633213 16_15.docx @ 103483 @ 1 @ 1
2 Intended use
Pos: 9 /DinA4 - A nleitungen Onlin e/Inhalt/KNX/D oorEntry/832 20-AP-xxx/B estimmungsg emaesser Ge brauch - 83220-AP-xxx- 500 @ 20\mod_1 32456116869 9_15.docx @ 1 12728 @ @ 1
This device is an integral part of the ABB-Welcome door communication system and
operates exclusively with components from this system. The device must only be
installed on mounting rails according to DIN EN 500022.
Pos: 10 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/Übersc hriften (--> Für alle Doku mente <--)/1. Ebene/U - Z/Umwelt @ 18\mod_1302 614158967_1 5.docx @ 1033 83 @ 1 @ 1
3 Environment
Pos: 11 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/U mwelt (--> Für alle Dokumente <--)/Hi nweise/Hi nweis - Umwelt - Hi nweis Elektrog eräte @ 18\mod_1302 763973434_1 5.docx @ 1035 00 @ @ 1
Consider the protection of the environment!
Used electric and electronic devices must not be disposed of with
domestic waste.
The device contains valuable raw materials that can be recycled.
Therefore, dispose of the device at the appropriate recycling
facility.
Pos: 12 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/2./ABB G eraete @ 19\m od_13231628438 32_15.docx @ 110875 @ 2 @ 1
3.1 ABB devices
Pos: 13 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/U mwelt (--> Für alle Dokumente <--)/Hi nweise/Hi nweis - Umwelt - A BB Elektrogeräte @ 19\ mod_13231627 45839_15.doc x @ 110867 @ @ 1
All packaging materials and devices from ABB bear the markings and test seals for
proper disposal. Always dispose of the packaging material and electric devices and their
components via an authorized recycling facilities or disposal companies.
Environment
|
4
ABB products meet the legal requirements, in particular the laws governing electronic
and electrical devices and the REACH ordinance.
(EU-Directive 2002/96/EG WEEE and 2002/95/EG RoHS)
(EU-REACH ordinance and law for the implementation of the ordinance (EG)
No.1907/2006)
Operation
|
5
Pos: 18 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/1./Bedienu ng @ 18\mod _13026139241 65_15.docx @ 103365 @ 1 @ 1
4 Operation
Pos: 19 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/2./Norm aler Betrieb @ 18\ mod_1302768 820965_15.d ocx @ 103540 @ 2 @ 1
4.1 Control elements
Pos: 20 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/3./Bedienel emente @ 20\ mod_132326 0220559_15.doc x @ 111647 @ 3 @ 1
Pos: 21 /DinA4 - Anleitungen Onli ne/Inhalt/KN X/DoorEntry/83 220-AP-xxx/Bedieneleme nte - 83220- AP-xxx @ 1 8\mod_13032 12853605_15.d ocx @ 103673 @ @ 1
Fig.
1
: Overview of control buttons
No.
Functions
1
Bus in/out
2
Operating mode settings: See chapter Operating modes for details.
3
Terminal resistor ON/OFF.
In video installations or audio- and video-combined installations, the switch
must be set as RC on on the last device of the line.
4
Rotary switches for addressing (01-99).
5
Connection with outdoor stations, or connection with bus in, in "line
amplifier" mode.
6
Operating status indicating LED
Pos: 22 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/S teuermodule - Online-Do kumentation (--> Für alle Dokume nte <--)/++++++ ++++++ Seitenumbruc h +++++++++ +++ @ 9\ mod_1268898668 093_0.docx @ 52149 @ @ 1
Operation
|
6
Pos: 26 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/2./Bediena ktionen @ 20\ mod_1323262 294281_15.docx @ 111911 @ 2 @ 1
4.2 Operating modes
Pos: 71 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/3./Abschlus swiderstand @ 19\mod_1 321958079906_15 .docx @ 1100 83 @ 3 @ 1
Pos: 72 /DinA4 - Anleitungen Onli ne/Inhalt/KN X/DoorEntry/Be dienung/Abschl usswiderstand se tzen 83220- AP-xxx @ 1 9\mod_131072 3392369_15.d ocx @ 1078 41 @ @ 1
4.2.1 Building gateway
Fig.
2
: Building gateway
No.
Functions
1
1->OFF, 2->OFF, 3->OFF
Pos: 74 /DinA4 - Anleitungen Onli ne/Inhalt/KN X/DoorEntry/Be dienung/Mast er/Slave Schalter s etzen 83220-AP- xxx @ 19\mod_1310 723320966_1 5.docx @ 10 7833 @ @
2
3
ON
1
1
Operation
|
7
Enable one building as an independent sub-system (outdoor station(s)/guard unit(s) can
be connected). Up to 60 such systems are supported within the whole system.
The gateway address is equal to the riser number.
Fig.
3
: Building gateway
Wiring diagram:
Fig.
4
: Building gateway
Operation
|
8
4.2.2 Floor gateway
Fig.
5
: Floor gateway
No.
Functions
1
1->OFF, 2->OFF, 3->ON
2
3
ON
1
1
Operation
|
9
Enable a multi-apartment as an independent sub-system (another outdoor station can
be connected, for example in front of the door of the floor with the multi-apartment).
The gateway address is equal to the minimum address of the indoor station inside the
sub-system.
Fig.
6
: Floor gateway
Operation
|
10
Wiring diagram:
Fig.
7
: Floor gateway
If using pushbutton outdoor station as a gate station, floor gateway is available for this
kind of use case.
In following example, an outdoor station is mounted at the gate entrance with which all
six apartments can be called. One outdoor station is on the left building with apartments
01 and 03 and a further outdoor station on the right building with apartments 04 and 05.
This means that only three apartments can be called from these two outdoor stations.
Using floor gateway for each building, and outdoor station 1 can manage these two
buildings, while outdoor station 2 manage the left building and outdoor station 3 manage
the right one.
Operation
|
11
Wiring diagram (using floor gateway for each building)
Apartment 01 A
Apartment 02 B
Apartment 03 C
Apartment 04 A
Apartment 05 B
Apartment 06 C
Outdoor station
Left building
Apartment 01 A
Apartment 02 B
Apartment 03 C
Apartment 04 D
Apartment 05 E
Apartment 06 F
Outdoor station
Gate entrance
Outdoor station
Right building
Apartment 01 A
Apartment 02 B
Apartment 03 C
Apartment 04 A
Apartment 05 B
Apartment 06 C
Apartment 01 A
Apartment 02 B
Apartment 03 C
Apartment 04 D
Apartment 05 E
Apartment 06 F
ST. X100 X10 X1
2 0 0 3
ST. X100 X10 X1
2 0 0 2
ST. X100 X10 X1
2 0 0 1
Address
2
Address
1
Address
3
ST. X100 X10 X1
3 0 0 4
ST. X100 X10 X1
3 0 0 5
ST. X100 X10 X1
3 0 0 6
M2302
X10 X1
0 1
M2302
X10 X1
0 4
Operation
|
12
4.2.3 Apartment gateway
Fig.
8
: Apartment gateway
No.
Functions
1
1->OFF, 2->ON, 3->OFF
2
3
ON
1
1
Operation
|
13
Enable one apartment as an independent sub-system (The 2nd confirmed outdoor
station can be connected). Up to 99 such systems can be supported within the whole
system.
The gateway address is equal to the apartment number.
Fig.
9
: Apartment gateway
Operation
|
14
Wiring diagram:
Fig.
10
: Apartment gateway
Operation
|
15
4.2.4 Additional power supply mode
Fig.
11
: Additional power supply mode
No.
Functions
1
1->OFF, 2->ON, 3->ON
2
3
ON
1
1
Operation
|
16
Enable an additional power source for systems with a system controller.
Fig.
12
: Additional power supply mode
Using gateway
+ system
controller as
auxiliary power
supply to
connect to
other indoor
stations in the
same building,
when one
system
controller cant
cover all
consmer units.
Operation
|
17
Wiring diagram:
Fig.
13
: Additional power supply mode
Operation
|
18
4.2.5 Line amplifier
Fig.
14
: Line amplifier
No.
Functions
1
1->ON, 2->OFF, 3->OFF
Strengthen the video signal and extend transmission. For increased distance please
refer to ABB-Welcome system manual.
Fig.
15
: Line amplifier
2
3
ON
1
1
Operation
|
19
Wiring diagram:
Fig.
16
: Line amplifier
Pos: 75 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/S teuermodule - Online-Do kumentation (--> Für alle Dokume nte <--)/++++++ ++++++ Seitenumbruc h +++++++++ +++ @ 9\ mod_1268898668 093_0.docx @ 52149 @ @ 1
Technical data
|
20
Pos: 76 /DinA4 - Anleitungen Onli ne/Ueberschrif ten/1./Technisc he Daten @ 18\ mod_130261 5863001_15.d ocx @ 103416 @ 1 @ 1
5 Technical data
Pos: 77 /DinA4 - Anleitungen Onli ne/Inhalt/KN X/DoorEntry/83 220-AP-xxx/Technische D aten - 832 20-AP-xxx @ 18\mod_13 03212854559_15. docx @ 103 705 @ @ 1
Designation
Value
Operating temperature
-25 °C - +55 °C
Protection
IP20
Single-wire clamps
2 x 0.28 m - 2 x 0.75 mm²
Fine-wire clamps
2 x 0.28 m - 2 x 0.75 mm²
Bus voltage
20-30 V
Pos: 78 /Busch-J aeger (Neustr uktur)/Modul-Stru ktur/Online-Do kumentation/S teuermodule - Online-Do kumentation (--> Für alle Dokume nte <--)/++++++ ++++++ Seitenumbruc h +++++++++ +++ @ 9\ mod_1268898668 093_0.docx @ 52149 @ @ 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

ABB M2302 User manual

Category
Gateways/controllers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI