WAGO 2DO 230 V AC 1.0 A, Relay 2CO, potential-free /XTR User manual

Pos: 2 /D ok ument ati on al lg em ein/E inb and /Ei nban d F ro ntsei te - Han dbuc h; C I 20 17; mit Do cVar ia ble n (St an dard) @ 28\mod_1486477502910_0.docx @ 405388 @ @ 1

Manual

WAGO-I/O-SYSTEM 750 XTR

750-517/040-000

2DO 230V AC 1.0A/ Relay 2CO /XTR

2-Channel Relay Output Module 230 VAC, 1.0 A,

2 Changeover Contacts /XTR

Version 1.3.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Rec htlic h es, A llg emei nes /Im pre ssu m f ür St and ard han dbüc her - al lg. Ang aben, A nschr iften, Telefo nnum mern un d E-Mail- Adres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 4 45 55

Fax: +49 (0) 571/8 87 – 84 45 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 XTR Table of Contents 3

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ............................................................. 5

1.1 Validity of this Documentation................................................................. 5

1.2 Copyright ................................................................................................ 5

1.3 Symbols ................................................................................................. 6

1.4 Number Notation .................................................................................... 8

1.5 Font Conventions ................................................................................... 8

2 Important Notes ........................................................................................ 9

2.1 Legal Bases ............................................................................................ 9

2.1.1 Subject to Changes ............................................................................ 9

2.1.2 Personnel Qualifications .................................................................... 9

2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ....... 9

2.1.4 Technical Condition of Specified Devices......................................... 10

2.1.4.1 Disposal ...................................................................................... 10

2.1.4.1.1 Electrical and Electronic Equipment ........................................ 10

2.1.4.1.2 Packaging ............................................................................... 11

2.2 Safety Advice (Precautions) ................................................................. 12

3 Device Description .................................................................................. 15

3.1 View ..................................................................................................... 17

3.2 Connectors ........................................................................................... 18

3.2.1 Data Contacts/Local Bus .................................................................. 18

3.2.2 Power Jumper Contacts/Field Supply .............................................. 19

3.2.3 CAGE CLAMP

®

Connectors ............................................................. 19

3.3 Display Elements .................................................................................. 20

3.4 Operating Elements .............................................................................. 20

3.5 Schematic Diagram .............................................................................. 21

3.6 Technical Data ..................................................................................... 22

3.6.1 Device Data ..................................................................................... 22

3.6.2 Supply .............................................................................................. 22

3.6.3 Communication ................................................................................ 22

3.6.4 Outputs ............................................................................................ 23

3.6.5 Connection Type .............................................................................. 23

3.6.6 Mechanical Conditions ..................................................................... 23

3.6.7 Climatic Environmental Conditions ................................................... 24

3.7 Load Limiting Curve .............................................................................. 24

3.8 Approvals ............................................................................................. 25

3.9 Standards and Guidelines .................................................................... 27

4 Process Image ......................................................................................... 33

5 Mounting .................................................................................................. 34

5.1 Mounting Sequence .............................................................................. 34

5.2 Inserting and Removing Devices .......................................................... 35

5.2.1 Inserting the I/O Module ................................................................... 35

5.2.2 Removing the I/O Module ................................................................ 37

4 Table of Contents WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

6 Connect Devices ..................................................................................... 38

6.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 38

6.2 Connection Examples ........................................................................... 40

6.2.1 1-Wire Connection, Protection Class I Actuators .............................. 40

6.2.2 1-Wire Connection, Protection Class II and III Actuators .................. 40

6.2.3 Operating the Relay in Separate Current Circuits ............................. 41

6.2.4 Operating the Relay in Series Connection ........................................ 42

6.3 Protective Circuits for Contacts of Relay Modules ................................ 43

7 Use in Hazardous Environments ........................................................... 45

7.1 Marking Configuration Examples .......................................................... 46

7.1.1 Marking for Europe According to ATEX and IECEx .......................... 46

7.1.2 Marking for the United States of America (NEC) and Canada

(CEC) ............................................................................................... 50

7.2 Installation Regulations......................................................................... 53

7.2.1 Special Notes Regarding Explosion Protection ................................ 53

7.2.2 Special Notes Regarding ANSI/ISA Ex ............................................ 55

List of Figures .................................................................................................. 56

List of Tables .................................................................................................... 57

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 5

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 1/Hi nwei s e zu dies er D o kume ntati on - Über schr ift 1 @ 4\mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Sic her heit s- und sonstige Hinweise/Hinweis/Hinweis : Dokumentation aufbewahren @ 4\mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation

is included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 2/G ültig kei tsb ereic h - Über schr ift 2 @ 12\mod_1338912448776_21.doc x @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on ( alt e Str uktur )/ Gül tig keits ber eic h/G ülti g keitsb erei ch D o kume ntat ion I/ O-Modul 750-xxxx, oh ne Vari anten angab e @ 14\mod_1358944037947_21.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-517/040-000

(2DO 230V AC 1.0A/ Relay 2CO /XTR).

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on ( alt e Str uktur )/H in weis e/A cht ung: Hi nw eis z ur D o kume ntati on I/O-M odul e 750- xxxx/040-000 @ 27\mod_1468502299549_21.docx @ 216892 @ @ 1

The I/O module 750-517/040-000 shall only be installed and operated according

to the instructions in this manual, in the system description for the WAGO-I/O-

SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750 XTR!

In addition to these operating instructions, you will also need the system

description “Design Notes XTR – Guidelines and Recommendations for

Increasing Operational Safety” and the manual for the used fieldbus

coupler/controller, which can be downloaded at www.wago.com

. There, you can

obtain important information including information on electrical isolation, system

power and supply specifications.

Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Ur heb ersc hut z - Ü bersc hr ift 2 @ 23\ mod_1435647042188_21.docx @ 184808 @ 2 @ 1

1.2 Copyright

Pos: 12.2 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Ur heb ersc hut z au sf ührli ch @ 4\ mod_1235565145234_21.docx @ 27691 @ @ 1

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12 .3 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 12.4 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ S ymbol e - Ü ber schr if t 2 @ 13\ mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/G efa hr/G efa hr: _War nu ng vor P ers on ensc hä den allg emei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son ensch äden d urch ele ktrisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule) /Sic herh eits - und so nst ige H i nweis e/ Warn ung/ War nung : _ War nu ng vor P ers one nsc häd en allg emei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Vorsic ht/V orsic ht: _War nung vor Pers one nschäd en allg emein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Achtu ng/A chtung : _War nung v or Sachsc häd en allg em ein _ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule) /Sic herh eits - und sonst ige Hi nweise/ Achtu ng/ Achtung : _War nung v or Sachsc häd en durc h elekt rostati sch e Aufla dung_ - Erläut erung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläut eru ng @ 13\mod_1343310326906_21. docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/I nfor mat ion/ Inf or mati on: _W eiter e I nfor mat ion all ge mein_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 7

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.6 /Dokumentation allgemei n/Gliederungselemente/---Sei te nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 12.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Dar st ellu ng der Z ahl ens yst eme - Über sc hrift 2 @ 2 3\mod_1435647128078_21.d ocx @ 184 811 @ 2 @ 1

1.4 Number Notation

Pos: 12.8 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Za hlens ys te me @ 3\mod_1221059454015_21.doc x @ 21711 @ @ 1

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated

with dots (.)

Pos: 12 .9 /All e Ser i en (Al lg emei ne M od ule)/ Über s chri fte n/Eb ene 2/ Schr ift kon venti on en - Ü bers chr ift 2 @ 23\ mod_1435647186005_21.docx @ 184814 @ 2 @ 1

1.5 Font Conventions

Pos: 12.1 0 / Alle Ser ie n (All ge mein e M odul e) /Re chtl ich es, Allg em ein es/Sc hr ift konv enti onen @ 3\mod_1221059521437_21.doc x @ 21714 @ @ 1

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.:

File

>

New

Input

Designation of input or optional fields are marked in bold letters,

e.g.:

Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.:

[F5]

Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 XTR Important Notes 9

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 14 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/Wi cht ige Erl äu ter unge n - Ü bers chr ift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Wi chtig e Er l äuter ung en - Ei nleit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15 .2 /All e Seri en (A llg emei ne M od ule) /Ü bers chri fte n/Eb ene 2/R ec htlic he Gr undlag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Änd er ungs vor beh alt - Über schr ift 3 und In halt @ 3\ mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all

rights arising from the granting of patents or from the legal protection of utility

patents. Third-party products are always mentioned without any reference to

patent rights. Thus, the existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/P erson alqu alifi kation/ Pers onalqu alifi katio n 750-xxxx - Ü ber schr ift 3 u nd I nh alt @ 3\ mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYST EM )/ Wic htig e Er läut eru nge n (al te Str ukt ur)/B esti m mung sg emäß e Ver w end ung/ Bes ti mmung sg emäß e V er wendu ng 7 50- xxxx - Üb ersc hrift 3 @ 32\ mod_1536041141528_21.docx @ 498494 @ 3 @ 1

2.1.3 Use of the 750 Series in Compliance with Underlying

Provisions

Pos: 15.6 /Serie 750 (WAGO-I/O-SYST EM )/ Wic htig e Er läut eru nge n (al te Str ukt ur)/B esti m mung sg emäß e Ver w end ung/ Bes ti mmung sg emäß e V er wendu ng 7 50- xxx x für Gerät e - STD - mit EN 61000-6-3 @ 3 \mod_1224064151234_21.docx @ 24070 @ @ 1

Fieldbus couplers, controllers and I/O modules found in the modular WAGO-I/O-

SYSTEM 750 receive digital and analog signals from sensors and transmit them

to actuators or higher-level control systems. Using controllers, the signals can

also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information in

the section “Device Description” > “Standards and Guidelines” in the manual for

the used fieldbus coupler or controller.

10 Important Notes WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Appropriate housing (per 2014/34/EU) is required when operating the

WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a

prototype test certificate must be obtained that confirms the correct installation of

the system in a housing or switch cabinet.

The implementation of safety functions such as EMERGENCY STOP or safety

door monitoring must only be performed by the F-I/O modules within the modular

WAGO-I/O-SYSTEM 750. Only these safe F-I/O modules ensure functional

safety in accordance with the latest international standards. WAGO's

interference-free output modules can be controlled by the safety function.

Pos: 15.7 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Te chni sc her Z us tand der Ger ät e - Ü bersc hri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. These

modules contain no parts that can be serviced or repaired by the user. The

following actions will result in the exclusion of liability on the part of WAGO

Kontakttechnik GmbH & Co. KG:

• Repairs,

• Changes to the hardware or software that are not described in the

operating instructions,

• Improper use of the components.

Further details are given in the contractual agreements. Please send your

request for modified and new hardware or software configurations directly to

WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.8 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 4/ E ntsor gen - Über schri ft 4 @ 30\ mod_1510145115652_21.docx @ 469859 @ 4 @ 1

2.1.4.1 Disposal

Pos: 15 .9.1 /Al le Seri en (All gemei ne Mod ule)/Ü bers chrift en/ Ebene 5/ Elektr o- und El ektr oni kg erät e - Üb ers chri ft 5 @ 3 2\mod_1537446988068_21.doc x @ 501657 @ 5 @ 1

2.1.4.1.1 Electrical and Electronic Equipment

Pos: 15.9 .2 /All e Ser ie n ( Allg emei ne Mod ule) /R echtl ich es , Allg em ein es/E le ktr o- un d Elektr onikg eräte @ 32 \mod_1532425086061_21. docx @ 491989 @ @ 1

Electrical and electronic equipment may not be disposed of

with household waste. This also applies to products without

this symbol.

Electrical and electronic equipment contain materials and substances that can be

harmful to the environment and health. Electrical and electronic equipment must

be disposed of properly after use.

WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary

nationally.

WAGO-I/O-SYSTEM 750 XTR Important Notes 11

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Environmentally friendly disposal benefits health and protects

the environment from harmful substances in electrical and

electronic equipment.

• Observe national and local regulations for the disposal of electrical and

electronic equipment.

• Clear any data stored on the electrical and electronic equipment.

• Remove any added battery or memory card in the electrical and

electronic equipment.

• Have the electrical and electronic equipment sent to your local

collection point.

Improper disposal of electrical and electronic equipment can be harmful to the

environment and human health.

Pos: 15 .9.3 /D okum entati on allg emei n/Glie derung sele mente /----Leerz eil e-(1Z) ---- @ 28\mod_1485262995837_0.docx @ 404006 @ @ 1

Pos: 15 .9.4 /Al le Seri en (All gemei ne Mod ule)/Ü bers chrift en/ Ebene 5/ Verp ackung - Übers chri ft 5 @ 3 2\mod_1537447044202_21.doc x @ 501662 @ 5 @ 1

2.1.4.1.2 Packaging

Pos: 15 .9.5 /Al le Seri en (All gemei ne Mod ule)/R echtl iches , Allge mein es/V erpac kung @ 32 \mod_1537446786416_21.doc x @ 501653 @ @ 1

Packaging contains materials that can be reused.

PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout

Europe. Directives and laws may vary nationally.

Environmentally friendly disposal of the packaging protects the environment and

allows sustainable and efficient use of resources.

• Observe national and local regulations for the disposal of packaging.

• Dispose of packaging of all types that allows a high level of recovery,

reuse and recycling.

Improper disposal of packaging can be harmful to the environment and wastes

valuable resources.

Pos: 15.1 0 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 15.1 1 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/ Sich erh eits hin weis e - Ü bers chr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.1 2 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/E inl ei tung Sic her heit shi nw eise Har dwar e @ 6\ mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.1 3. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : N ich t an G erät en unter S pann ung ar beite n! @ 6\ mod_ 1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 3. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /Gef a hr/G efahr : Pr od ukt nur i n ein em g eeig net en Geh äuse ei nba uen! @ 3 3\mod_1543581881435_21.docx @ 511972 @ @ 1

Install device in only one suitable enclosure!

The device is an open system. Install the device in a suitable enclosure. This

enclosure must:

• Guarantee that the max. permissible degree of pollution is not exceeded.

• Offer adequate protection against contact.

• Prevent fire from spreading outside of the enclosure.

• Offer adequate protection against UV irradiation.

• Guarantee mechanical stability

• Restrict access to authorized personnel and may only be opened with tools

Pos: 15.1 3. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinwei se /Gef ahr /Gef ahr: Tr enn vorr ich tung un d Ü ber stro msc hutz @ 33\ mod_1543915978439_21.docx @ 512267 @ @ 1

Ensure disconnect and overcurrent protection!

The device is intended for installation in automation technology systems.

Disconnect protection is not integrated. Connected systems must be protected by

a fuse.

Provide suitable disconnect and overcurrent protection on the system side!

Pos: 15.1 3. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : U nfal l verh ütung s vorsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 3. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : A uf nor mger ec hte n Ansc hl uss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1

Ensure a standard connection!

To minimize any hazardous situations resulting in personal injury or to avoid

failures in your system, the data and power supply lines shall be installed

according to standards, with careful attention given to ensuring the correct

terminal assignment. Always adhere to the EMC directives applicable to your

application.

Pos: 15.1 4 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/G ef ahr /Gef ahr: Lei tung en nur i n spa nnu ngs frei em Z ust and ans chl iess en oder tr enn en @ 16\mod_1372153982130_21.docx @ 124277 @ @ 1

WAGO-I/O-SYSTEM 750 XTR Important Notes 13

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Only connect or disconnect lines when power is safely isolated!

The lines to the device can carry hazardous voltages and currents. Contact with

the lines when live can result in severe injury or death. Therefore, read and

observe the following safety rules before you perform work on the device:

1. Disconnect the respective system component from the power supply.

2. Secure the system component against unintentional restart.

3. Check if the voltage is positively isolated.

Pos: 15.1 5 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/V ors ic ht/Vor sic ht : H eiße Ober fl äc he nic ht ber ühre n! (all ge mein) @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1

Do not touch hot surfaces!

The surface of the housing can become hot during operation. If the device was

operated at high ambient temperatures, allow it to cool off before touching it.

Pos: 15.1 6. 1 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en (alt e St ruk tur) /Si cher hei ts- und s ons tig e Hi nwei se/ Ac htung /Ac ht ung: Ei nwa ndfr eie Ko nta ktier ung zur Trag sc hie ne g ew ährl eist en! @ 3 4\mod_1550481407638_21.doc x @ 530599 @ @ 1

Ensure proper contact with the DIN-rail!

Proper electrical contact between the DIN-rail and device is necessary to

maintain the EMC characteristics and function of the device.

Pos: 15.1 6. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : D efe kte oder bes ch ädigt e Ger äte aust ausc hen! @ 6\ mod_1260180857358_21.doc x @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts).

Pos: 15.1 6. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Geräte vor kriechenden und isolierenden Stoffen schütze n! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for

handling devices/modules.

Pos: 15.1 6. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : R einig ung nur mi t zul äs sig en M at erial ien! @ 6\mod_1260181203293_21.doc x @ 46751 @ @ 1

Clean only with permitted materials!

Clean housing and soiled contacts with propanol.

Pos: 15.1 6. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755 @ @ 1

14 Important Notes WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 6. 6 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : V erpol ung en der Dat en- und Ver sorg ungsl eitu ngen ver meide n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15 .16. 7 /Alle S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : El ektr ost atis ch e En tla dung v ermei de n! - DIN EN 61340-5-1/- 3 @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 15.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - un d son sti ge Hi n weis e/Ac ht ung/ Ac htung : XT R - Isol ati onspr üf ung en mit DC d urch fü hren! @ 15\mod_1370843209441_21.docx @ 122210 @ @ 1

Use only direct current (DC) for insulation testing!

Both the system voltage and field voltage side are capacitively coupled to the

DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage

between the DIN-rail and at least one of these two potentials can lead to the

destruction of the module.

Use only direct current (DC) for insulation testing. To avoid destroying the I/O

module, you must discharge it completely before applying the test voltage again.

Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 XTR Device Description 15

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/G erät e besc hrei bung - Ü ber schri ft 1 @ 3\mod_123375608 465 6_2 1.doc x @ 27 096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger ätebesc hrei bung (al te Str uktur )/Einl eitu ng/An wendu ng/DO /Anw endung 750-05 xx DO Rel ais @ 5\ mod_1246611276875_21.doc x @ 36561 @ @ 1

The 750-517/040-000 Digital Output Module transmits binary control signals from

the automation device to the connected actuators (e.g., solenoid valves,

contactors, transmitters, relays or other electrical loads).

Pos: 18.2 /S erie 750 (WAGO-I/O-SYST EM) /Ger äte bes chr ei bung (alt e St ru ktur )/Ei nlei tu ng/I /O-B esc hrei bung /DO /I/O -Besc hr eibu ng 7 50- 0517 2 D O 2-Leit er (DO od er /DO ) @ 17 \mod_1384158208113_21.docx @ 136978 @ @ 1

The I/O module has 2 output channels, providing a direct connection to actuators.

The actuators can be wired directly to the CAGE CLAMP

®

connectors DO 1 or

/DO 1 (i.e. NOT DO 1) of channel 1 resp. DO 2 or /DO 2 (i.e. NOT DO 2) of

channel 2.

Pos: 18.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung/ I/O- Besc hrei bu ng/Al lge mei n/V er weis auf Kapi tel "An schl üss e" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " Ger ät e ans chl ieß en" > " Ansc hl ussb eis piel (e)" @ 5\mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connect Devices” > … >

“Connection Example(s)”.

Pos: 18 .5 /Serie 750 (WAGO-I/O-S YSTEM) /Wic htige Er läut erung en (alt e Stru ktur)/Si cher heits - und sonstige Hinweise/Achtung/Achtung: DO Induktionsspannungsbegrenzung Relais @ 5\mod_1247031985231_21.docx @ 36766 @ @ 1

Inductive loads must be dampened!

For the protection of relay coils and contacts, inductive loads must be dampened

with an effective protection circuit!

Examples of protection circuits can be seen in the section “Protective Circuits for

Contacts of Relay Modules”.

Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr eibu ng/D O/I/ O-B esc hrei bung 75 0-0 5xx Wec hsler @ 5\ mod_1246866311313_21.docx @ 36609 @ @ 1

The I/O module incorporates 2 change-over relays connected potential free.

This means on the field side only the connections of the relay contacts are

present. Therefore, both relays can be operated with different voltages.

Because of the potential free contacts also a serial connection of the 2 relays is

possible as well as a serial connection of several relays with block wise

connection of several modules.

Pos: 18.7 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr eibu ng/D O/I/ O-B esc hrei bung 75 0-0 517/ 040- 000 R elai sko nt akte 11 u nd 21 @ 2 2\mod_1425393378367_21.docx @ 1765 77 @ @ 1

The relay contacts 11 and 21 can be connected to an external voltage of

230 VAC resp. 300 VDC.

Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: Keine Verwe ndu ng von u nt erschi edl ic hen Pha sen ein es Dr eh stro mn etz es an bei de n Ka näl en @ 22\ mod_1425393912913_21.docx @ 176585 @ @ 1

No use of different phases of a three-phase system on both channels!

The max. voltage between adjacent connections may not exceed 250 VAC. The

use of different phases of a three-phase system on both channels of the relay

output module 750-517/040-000 is not permitted!

Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng ( alt e Str u ktur) /Ei nleit u ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bu ng 7 50-0 514, -517 Dur chsc hal tu ng d es mi ttl er en Rel ai sk onta ktes @ 2 2\mod_1425393644292_21.doc x @ 176581 @ @ 1

Depending on the relay status the voltage of the middle contact 11 resp. 21 is

switched to the lower contact 12 resp. 22 or to the upper contact 14 resp. 24. In

the OFF state the contacts 11 resp. 21 are switched to the lower contacts 12

resp. 22.

Pos: 18.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/Ei nl eitung /I/ O-Bes chr eib ung/D O/ I/O- Beschr eib ung 750- 05x x Ans te uer ung der R el ais ( Int ern e S yste msp ann ung) @ 5 \mod_1246861676649_21.docx @ 36599 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

The internal system voltage is used to trigger the relays.

Pos: 18.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebe schr ei bu ng (al te Stru ktur )/ Einl eit ung/ LED- Anzeige/LED Zustand Relais @ 5\mod_1246862048946_21.docx @ 36603 @ @ 1

The switching status of the two relays is indicated via green status LEDs.

Pos: 18.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng (al te Stru ktur) /Einl eitung /LED- Anz eige /V er weis a uf Kapit el " An zeig eel em ent e" @ 5\ mod_1246010525000_21.doc x @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/ Einl eit ung/ Vers org ung /A nordn ung unt er Ber üc ksic htig ung der Leis tu ngs kon takt e b elie big @ 3\ mod_1233756233468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node.

An arrangement in groups within the group of potentials is not necessary.

Pos: 18.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herheit s- un d son stig e Hi n weis e/Hi nw eis/H in weis: P oten tial eins p eise modul für Er de ein setz en! ( keine LK f ür Erd e) @ 3\ mod_1226499037468_21.docx @ 25023 @ @ 1

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.1 5 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Hinweis/Hinweis: XTR - Er höht e S tör festi g keit @ 1 5\mod_1367496424993_21.docx @ 118330 @ @ 1

Increased interference!

For standard-compliant application in substation instrumentation and control,

telecontrol systems, railway technology or shipbuilding certified operation,

field-side power supply filter 750-624/040-001 or power supply filter

750-626/040-000 are generally to be used for XTR module groups.

Pos: 18.1 6 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Hinweis/Hinweis: XTR - Misc hbetri eb XTR/ Stan dard @ 1 5\mod_1367496420828_21.docx @ 118326 @ @ 1

Mixed operation

Mixed operation (standard/XTR modules) within a node is possible when groups

of modules are electrically isolated on the field side (i.e., electrically isolated

power supply).

Pos: 18.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/ Einl eitung /Eins atzb ereic h/Eins atzb ereic h 750-xxxx/0 40-000 all e XT R-K oppl er/ Cont rol ler ohne Ei nsc hrä nkung +M isc hb etrie bhi nw eise @ 1 5\mod_1368425919479_21.docx @ 119444 @ @ 1

The I/O module can be operated with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750 XTR.

Observe the instructions for mixed operation when used in mixed operation

behind standard fieldbus couplers/controllers.

Pos: 19 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 XTR Device Description 17

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 20 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsi cht - Üb ersc hrif t 2 @ 4 \mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsi cht/D O/ An sicht 75 0-0517/0040-xxxx @ 16\mod_1372413203476_21.docx @ 125117 @ @ 1

Figure 1: View

Pos: 22 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsi cht/ A nsich t C ageC lam p® _Leg en de mi t LE Ds _oh ne L eist ung sko nta kte @ 16 \mod_1371816091053_21.docx @ 124052 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status LEDs

“Device Description” > “Display Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Release tab

“Mounting” > ”Inserting and Removing

Devices”

Pos: 23 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 24 /Alle Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsc hlüs se - Üb erschr ift 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 25 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /Da ten kont akte /L okal bus - Ü b ersc hrif t 3 @ 6 \mo d_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Local Bus

Pos: 26.1 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Ansc hlüs se /Da ten kon takt e - Fel d busko ppl er/-c ont roll er und Modul e – Abbi ld ung un d Besc hr eib ung @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the local bus. The

contacting for the local bus consists of 6 data contacts, which are available as

self-cleaning gold spring contacts.

Figure 2: Data Contacts

Pos: 26.2 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: I/O-Modul e nicht a uf Goldf eder konta kte lege n! @ 7\ mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 26.3 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: ESD - Auf Pote nti ala usgl eic h der U mgeb ung ac hte n! @ 32\ mod_1539077262331_21.docx @ 504433 @ @ 1

Pay attention to potential equalization from the environment!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, please ensure that

environmental factors (personnel, work space and packaging) are properly

equalized. Do not touch any conducting parts, e.g., data contacts.

Pos: 27 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 XTR Device Description 19

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 28 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str uktur) /Ansc hlüss e/Lei stung skont akte/F eld versor gung - Ü ber schri ft 3 @ 6\ mod_1256294692864_21.doc x @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /Lei stu ngs kont a kte ni cht vor ha nden @ 8\ mod_1281073936319_21.docx @ 62530 @ @ 1

The I/O module 750-517/040-000 has no power jumper contacts.

Pos: 30.1 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und s onstig e Hin weise/ Hinw eis/Hi nweis : Pote ntialei nspei se modul ei nsetz en! (kei ne LK) @ 3\ mod_1226499089640_21.docx @ 25026 @ @ 1

Use a power supply module!

Use a power supply module for field-side power supply of downstream I/O

modules.

Pos: 31 /Dokumentatio n allge mein/ Glieder ungs elem ente/---S eite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /CA GE C LAM P-Ans chl üss e - Ü bersc hri ft 3 @ 6\mod_1256296337770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

®

Connectors

Pos: 33 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung (al te Str uktur) /Ansc hlüss e/DO/ Ansc hlüss e 750-0517 @ 16\mod_1371808833394_21.docx @ 123957 @ @ 1

Figure 3: CAGE CLAMP

®

Connectors

Table 4: Legend for Figure “CAGE CLAMP

®

Connectors”

Channel

Designation

Connector

Function

1

14

1

Output DO 1: Normally open contact

11

2

Load line

12

3

Output /DO 1: Normally closed contact

2

24

5

Output DO 2: Normally open contact

21

6

Load line

22

7

Output /DO 2: Normally closed contact

Pos: 34 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750 XTR

750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR

Manual

Version 1.3.0

Pos: 35 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nzei g eele ment e - Ü ber schr ift 2 @ 4\ mod_1240984390875_21.doc x @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 36 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung (al te Str uktur) /Anz eigeel ement e/DO/ Anzei geele ment e 750-0 517 2 R O ( Agn, Egn) @ 16\mod_1372343976705_21.doc x @ 125054 @ @ 1

Figure 4: Display Elements

Table 5: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1

State

relay 1

A

off

Normally open contact DO1 opened

Normally closed contact /DO1

closed

Green

Normally open contact DO1 closed

Normally closed contact /DO1

opened

2

State

relay 2

E

Off

Normally open contact DO2 opened

Normally closed contact /DO2

closed

Green

Normally open contact DO2 closed

Normally closed contact /DO2

opened

Pos: 37 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/B edi enel e ment e - Ü bers chri ft 2 @ 4\mod_1239191655456_21.docx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 38 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/B edi enel e ment e/Be di enele me nte I /O-Modul 75x-xxxx nicht vorhanden @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1

The I/O module 750-517/040-000 has no operating elements.

Pos: 39 /Doku ment ation all gemei n/Gli eder ungsel emente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Page is loading ...

WAGO 2DO 230 V AC 1.0 A, Relay 2CO, potential-free /XTR User manual

WAGO 2DO 230 V AC 1.0 A, Relay 2CO, potential-free /XTR User manual

Related papers

Other documents