NOAM NUTV5 User manual

Brand: NOAM

Model: NUTV5

Type: User manual

This manual is also suitable for

NUTV5-S

NOAM NUTV5-S is a complete marine audio system that combines speakers, an amplifier, and a controller for a fully functional audio setup. It's waterproof and designed for outdoor use, making it ideal for boats, ATVs, UTVs, and other marine vehicles. The system includes a pair of 5.25-inch marine speakers with passive radiators for enhanced bass, an 8-inch marine subwoofer, a 4-channel marine amplifier with variable crossovers, and a waterproof Bluetooth controller for wireless music streaming and control.

2 11

Owner’s Manual

NUTV5 / NUTV5-S

What’s Included

SENS – Gain settings:

NOTE: This is NOT a volume control.

This control is used to match the input of the ampliﬁer to the source unit.

The higher the sensitivity the sooner the amp will reach maximum output.

While this ampliﬁer is designed to be water-resistant, it should never be submerged

under water or subjected to high-pressure water spray. Do not install where it will be

directly exposed to the elements.

Heaving an ampliﬁer sealed to the elements at IPX6 level

means that heat generated inside the amp has nowhere to

escape. Playing hard with your NA4 will get it Hot. That’s ﬁne

and normal. But, avoid touching the ampliﬁer’s surface during

or right after use.

As already noted, the NA4 control panel was preset to be used with the

NOAM N5 and NOAM NSUB. In case you need to make adjustment to

the gain settings, please follow these steps:

Your NA4 ampliﬁer is an IPX6 waterproof level.

POWER OUTPUT AT 4 Ω

FREQUENCY RANGE

Your

Speciﬁcations:

Though this is a Marine IPX6 rated ampliﬁer, whenever possible, mount

the ampliﬁer in a dry, well-ventilated location that does not interfere with

other factory installed electronic devices. If a dry environment is not

available, a location that is not exposed to heavy splashing may be used.

1. Turn the gain control (SENS) all the way down counterclockwise.

2. Turn your NR controller ON.

3. If you are using your phone or MP3 player to stream music to your NR controller, tune

both audio source and NR controller to MAX volume.

4. Slowly increase the gain control. Stop when you hear slight audio distortion.

Introduction

NA4 Ampliﬁer:

NR Controller:

NUTV5 NUTV5-S

N5 - Pair of 5.25” Marine speakers

NR – Waterproof Bluetooth Controller

NA4 – 4 channels Marine Ampliﬁer

All wires and mounting accessories

NSUB – 8” Subwoofer

NR – Waterproof Bluetooth Controller

NA4 – 4 channels Marine Ampliﬁer

N5 - Pair of 5.25” Marine speakers

* Detailed accessory list for each speakers, controller and ampliﬁer can be found inside each

component’s manual.

Both NUTV5 & NUTV5-S were built as a system. All included components of the unit;

Speakers, ampliﬁer & controller were designed and tuned to match one another and

function as a full audio system.

The NA4 is an IPX6 waterproof, state of the art, Class D, 4-channel full range ampliﬁer with

fully variable high pass and low pass crossovers enabling it to drive a wide variety of either

full range speakers or subwoofers.

This manual will explain how to install your unit as a whole. Detailed

instructions for each; NA4 ampliﬁer, NR controller and N5/NSUB

speakers can be found separately inside your NUTV5 / NUTV5-S package.

*We strongly recommend to take the time and read each of the manuals*

Thank you for purchasing a NOAM Marine audio system. Your stereo system has been

designed and manufactured to exacting standards in order to ensure years of musical

enjoyment. At NOAM we plan and design our products so you can install it by yourself

and save the extra dollars for a professional installation. But, for maximum performance,

we highly recommend that you have your new NUTV5 / NUTV5-S installed by a

professional audio shop. Professional audio dealer has the training, expertise and

installation equipment to ensure optimum performance from this product. Should you

decide to install the system yourself, please take the time to read all manuals thoroughly

to familiarize yourself with its installation requirements and setup procedures. If you have

any questions regarding the instructions written in any of the manuals or any aspect of your

opesystem’s ration, please contact your authorized NOAM

dealer for assistance or directly to us at

sales@noamaudio.com

The NR Bluetooth controller is your head unit. The NR features Bluetooth streaming and

AUX input. Rated at IPX7 waterproof level, your NR will endure wild weather conditions for

years.

Do not increase any “Input Sens.” setting for any ampliﬁer channel or channel pair

in the system beyond the maximum level established during this procedure. Doing

so will result in audible distortion and possible speaker damage.

Waterproof:

CROSSOVER RANGE

GAIN RANGE

S/N RATIO REF 1W AT 4 Ω

TOTAL HARMONIC DISTORTION

WATERPROOF LEVEL

POWER OUTPUT AT 4 Ω BRIDGED

POWER OUTPUT AT 2 Ω

60W x 4

20Hz-20KHz

40Hz-500Hz

0.2V-5.0V

>90dB

0.07%

IPX66

180W x 2

90W x 4

10 3

N5 Speakers: Control Panel Settings and Adjustments:

NA4 modes:

default settings:

2 Stereo Front + 1 Bridged Mono Rear Output

supplied with your kit or in case of distortion,

your default settings should be perfect.

Filter mode and Sensitivity (‘GAIN’) settings:

Filter mode:

HPF - (High-Pass) Conﬁgures Filter to Attenuate Frequencies

BELOW the Selected Filter Frequency.

LPF - (Low-Pass) Conﬁgures Filter to Attenuate Frequencies

ABOVE the Selected Filter Frequency.

FULL - Full-Range Operation of Input Signals

As mentioned, Your NA4 ampliﬁer’s control panel was preset to ﬁt the N5 Full-range

speakers and NSUB subwoofer supplied with the NUTV5/NUTV5-S stereo system. Unless

avoid adjusting the gain and crossover settings of the ampliﬁer.

The pair of N5 speakers features front 5.25” Water-proof Speaker and 20 mm PEI

Diaphragm tweeter. On the back, you’ll ﬁnd a passive radiator for increased bass

experience.

NSUB Subwoofer:

The NSUB is the very ﬁrst roll cage mounted subwoofer. Equipped with 8” Marine

Subwoofer Speaker on the front and pair of 3”x6” passive radiator on the back.

* only included in the NUTV5-S model.

Smart Handle:

Both the N5 and NSUB speakers uses our Smart Handle. we created the smart handle with

the ease of use in mind. The main purpose of the smart handle is to allow super-fast and

easy installation of the NSUB & N5 speakers.

* THIS MANUAL AND OTHERS CAN ALSO BE

FOUND ON OUR WEBSITE UNDER ‘SUPPORT’

SECTION *

WWW.NOAMAUDIO.COM

4 channels stereo mode:

2 Stereo Front + 2 Stereo Rear Output

Using the ampliﬁer with 4 full range speakers

Will require you to change the settings.

* Input gain (SENS) should be tested and tuned

In accordance with the used speakers and audio

Source.

** Crossover control should be tuned to ‘FULL’

2 bridged stereo output:

Using the ampliﬁer for 2 briged, full range speakers,

Will require you to change the settings.

* Input gain (SENS) should be tested and tuned

In accordance with the used speakers and audio

Source.

** Crossover control should be tuned to ‘FULL’

Rear / Left +

Rear / Left - // Sub-

Rear / Right + // Sub+

Rear / Right -

Front / Left +

Front / Left -

Rear / Right + // Sub+

Rear / Left - // Sub-

Front / Left +

Front / Left -

Front / Right -

Front / Right +

Rear / Right + // Sub+

Rear / Left - // Sub-

Front / Right +

Front / Left -

Front / Right -

Front / Right +

4 9

A. Installation Applications:

The NUTV5 / NUTV5-S is designed for operation with 12 volts, negative-ground electrical

systems. Using this product in systems with positive ground and/or voltages other than

12V may result in damage to the product and will void the warranty.

B. Safety Considerations:

C. Battery and charging:

• Though this is a Marine IPX6 rated ampliﬁer, whenever possible, mount the ampliﬁer in a dry,

well-ventilated location that does not interfere with other factory installed electronic devices.

If a dry environment is not available, a location that is not exposed to heavy splashing may be

used.

• While this ampliﬁer is designed to be water-resistant, it should never be submerged under

water or subjected to high-pressure water spray. Do not install where it will be directly

exposed to the elements.

reasons you might want to re-tune and readjust it. Take your time and make only one

adjustment at a time. It may take some time to get the system fully adjusted. During this time,

the amp is drawing current from the battery. You should check the battery voltage from time

to time and recharge it if it gets low.

Ampliﬁers will put an increased load on the vehicle’s battery and charging system.

We recommend checking your alternator and battery condition to ensure that the

electrical system has enough capacity to handle the increased load of your stereo

system. Stock electrical systems which are in good condition should be able to

handle the extra load of the NA4 ampliﬁer without problems, although battery and

alternator life can be reduced slightly. To maximize the performance of your ampliﬁer,

we suggest the use of a heavy-duty battery and an energy storage capacitor

• Securely mount the ampliﬁer so that it does not come loose in the event of a

collision/sudden jolt or as a result of repeated vibrations during normal operation.

• Check before drilling to make sure that you will not be drilling into an exterior panel/hull,

fuel tank, gas/brake line, wiring harness, or other vital system.

Heaving an ampliﬁer sealed to the elements at IPX6 level means that

heat generated inside the amp has nowhere to escape. Playing hard with

your NA4 will get it Hot. That’s ﬁne and normal. But, avoid touching the

ampliﬁer’s surface during or right after use.

Do not mount the ampliﬁer in the engine compartment or in any areas of extreme heat.

Mounting the unit in the engine compartment will void your warranty.

• Protect all system wires from sharp edges (metal, ﬁberglass, etc.) by carefully routing

them, tying them down and using grommets and loom where appropriate.

• Secure all wiring as needed, using cable ties or wire clamps to protect them from

moving parts and sharp edges.

Do not run system wiring outside or underneath the vehicle/vessel. This is an

extremely dangerous practice, which can result in severe damage/injury.

More about the NA4 Ampliﬁer

Get to know your NA4

The NA4 ampliﬁer is state of the art Class D ampliﬁer designed to

audio system. The NA4 is a 4-channel full range ampliﬁer with fully

variable high pass and low pass crossovers enabling it to drive a wide

variety of either full range speakers or subwoofers.

The NA4 ampliﬁer is meant to work with the NOAM NR Bluetooth

controller. The NR controller is your audio source head-unit, able to

trigger your ampliﬁer ON/OFF.

What’s Included

• NA4 - 4 channels Marine ampliﬁer

1. Input – waterproof DIN plug allows you to connect your NA4

ampliﬁer to the NOAM NR Bluetooth controller/receiver.

2. Red / positive power wire – includes a 40A fuse and fuse holder.

3. Black / ground power wire.

4. Blue / remote Turn On - *optional – you don’t need to use it in order

to power your NA4 ampliﬁer

5. Output channels

• 8’ power wire

• 40A fuse and fuse holder

• 4 pcs of mounting screws

Red +12V

Black Ground

Blue Remote

Green/Black Rear Left - / Sub -

Purple Rear Right + / Sub +

White/Black Front Left -

Grey Front Right +

Grey/Black Front Right -

White Front Left +

Purple/Black Rear Right -

Green Rear Left +

Rear Left - / Sub -

Rear Right + / Sub +

Front Left -

Front Right +

Front Right -

Front Left +

Rear Right -

Rear Left +

Red

Black

Blue

Green/Black

+12V

Ground

Remote

Rear Left - / Sub -

Purple

6Rear Right + / Sub +

White/Black

8Front Left -

Grey

10 Front Right +

Grey/Black

11 Front Right -

White

9Front Left +

Purple/Black

7Rear Right -

Green

5Rear Left +

WIRE# COLOR CODE FUNCTIONE

8 5

Refer to section D

TROUBLESHOOTING

Power/Protect Indicator:

This indicator will light up RED upon initial amp start up. If all connections are OK, within

3-5 seconds the light will turn to BLUE. If a condition of protect (short circuit, over/under

voltage) occurs the light will turn to RED until the condition of protect is resolved.

Problem Cause Solution

It just doesn’t sound right

Ampliﬁer doesn’t turn on

Balance Reversed

Output Distorted

a while

Blowing Fuses

Whining or ticking noise

while the engine is ON

Speaker are connected to the wrong output Refer to section E of this owner manual

Control panel settings are wrong Refer to section E of this owner manual

Controller wasn’t turned ON Did you remember to press and hold the

controller’s power button for 3-5 seconds?

Faulty fuse Remove fuse and check with continuity

meter. Replace if necessary.

Poor connection integrity Check “+12V” and “Ground” leads for

pinched wires; ensure tight connections.

Speaker Wire L & R Reversed Correct Speaker Wire Orientation

NR/Audio player Volume Set Too High L

Ampliﬁer Gain Set Too High Lower Ampliﬁer Gain (SENS)

ower NR/Audio player Volume

Overheating condition

(Thermal Protection)

Make sure ampliﬁer mounting area has

adequate space for ventilation and heat

dissipation.

Excessive Output Levels Lower the Volume

Amp is defective Contact us at sales@noamaudio.com

The ampliﬁer is picking up alternator

or radiated noise

Turn Down input gain (SENS)

ove the audio cables away from the

power wires

Check the alternator and/or voltage

regulator. Test for weak battery or add

water to the battery

PWR

PRT

Red

Black

Blue

Green/Black

Purple

White/Black

Grey

Grey/Black

White

Purple/Black

Green

+12V

Ground

Remote

Rear Left - / Sub -

Rear Right + / Sub +

Front Left -

Front Right +

Front Right -

Front Left +

Rear Right -

Rear Left +

Rear Left - / Sub -

Rear Right + / Sub +

Front Left -

Front Right +

Front Right -

Front Left +

Rear Right -

Rear Left +

Red

Black

Blue

Green/Black

+12V

Ground

Remote

Rear Left - / Sub -

Purple

6Rear Right + / Sub +

White/Black

8Front Left -

Grey

10 Front Right +

Grey/Black

11 Front Right -

White

9Front Left +

Purple/Black

7Rear Right -

Green

5Rear Left +

WIRE# COLOR CODE FUNCTIONE

6 7

D. Installation Procedure/Connections E. Control Panel Settings and Adjustments:

This is your default control panel settings:

If you feel unsure about installing this system yourself, have it installed by a

qualiﬁed technician.

Before installation Disconnect the NEGATIVE battery post connection and secure

the disconnected cable to prevent accidental reconnection during installation. This

is an essential safety precaution during installation!

Avoid running power wires near the low-level input cables, antenna, power leads,

sensitive equipment or harnesses. The power wires carry substantial current and

could induce noise into the audio system.

1. Connect the RED power lead to the positive (+12V) battery post.

The ampliﬁer’s settings and controls are located on the side panel beneath a gasketed,

protective cover. Remove the ﬁve Allen head screws from the center panel to access the

controls and make adjustments. Replace cover when ﬁnished and mount the ampliﬁer.

Your NA4 ampliﬁer’s control panel was preset to ﬁt the N5 Full-range speakers and

NSUB subwoofer supplied with the NUTV5/NUTV5-S stereo system. Unless you use

adjusting the gain and crossover settings of the ampliﬁer.

These settings are true for both NUTV5 and NUTV5-S models. Even if you bought the

NUTV5 without the NOAM NSUB, your ampliﬁer’s REAR channels are still set to the

NSUB subwoofer bridge mode.

Since the control panel is preset, please make sure you connect your speakers

to the right output channels.

IMPORTANT! Your NA4 ampliﬁer control panel was preset to work as part of the

NUTV5 / NUTV5-S audio system.

3. Fuse. Your NA4 already includes a 40A fuse. The NA4 power wires are 8’ long, while the

Fuse housing located on the Red/Positive power wire at 5’ of wire from the ampliﬁer.

4. Connect the NR male controller DIN plug to the NA4’s female DIN plug.

* Powering the NA4 ampliﬁer. Long pressing your NR controller’s power button for few

seconds will trigger both the NR controller and the NA4 ampliﬁer ON/OFF.

5. Run the speakers wires to the ampliﬁer’s output.

Make sure about correct polarity when connecting your speakers to the ampliﬁer.

speaker’s Red wire (+) should connect to color (+) output channels.

speakers’s Black wire (-) should be connected to color / Black (-) output channels.

Speaker connection color codes:

6. If you haven t already done so, mount the amp now.

7. Now you should be good to go and play tunes for the ﬁrst time.

2. We strongly recommend to run the Black/Ground power cable to the negative (-12V)

battery post.

Blue / Remote Turn-On wire is not required for installing or running your NA4

ampliﬁer. The NR controller is able to power trigger your ampliﬁer

You have plenty of power wire length before the fuse holder (5’). Strive to leave

no more than 18” (45.7 cm) of wire between the fuse holder and the battery

positive (+12V) terminal. You can cut the remaining wire.

FRONT – N5 Speakers

(or other full range speakers) REAR – NSUB subwoofer

The FRONT channels are set to power

your N5 full range speakers. Make sure

you connect the pair of N5 speakers to

the FRONT output channels.

The REAR channels are set to power your

NSUB subwoofer. Make sure you connect

the NSUB subwoofer to the REAR output

channels.

Rear Left - / Sub -

Rear Right + / Sub +

Front Left -

Front Right +

Front Right -

Front Left +

Rear Right -

Rear Left +

Red

Black

Blue

Green/Black

+12V

Ground

Remote

Rear Left - / Sub -

Purple

6Rear Right + / Sub +

White/Black

8Front Left -

Grey

10 Front Right +

Grey/Black

11 Front Right -

White

9Front Left +

Purple/Black

7Rear Right -

Green

5Rear Left +

WIRE# COLOR CODE FUNCTIONE

Front / Right + Grey

Front / Left + White

Front / Left - White/Black

Front / Right - Grey/Black Rear / Right + // Sub+ Purple

Rear / Left - // Sub- Green/Black

158mm (6.22”) 214.37mm (8.44”)

38.1mm (1.5”) or

44.45mm (.75”) or

46.99mm (1.85”) or

50.8mm (2”)

25mm (1.0”) 56.8mm (2.24”)

1 pair - N5 speakers

1 pair - Smart handle screw

1 pair - Flange nut

2 pair - of each 1.5”, 1.75”, 1.85” & 2” rubber inserts

2 pair - aluminum mounting bands

Mounting Dimensions(enclosure):

Power Rating: 150 W MAX /75 W RMS

Sensitivity: 90 dB @ 1W/1M

MidBass: 5.25” Water-proof Speaker

Tweeter : 20 mm PEI Diaphragm

Nominal Impedance: 4 ohm

Length: 214.4mm(8.44”)

Width: 158mm(6.22”)

Height: 236.9mm(9.33”)

N5 5.25” Tower speaker 150W/75W RMS Power Handling

Thank you for choosing NOAM N5 Marine speakers.

the creation of these speakers. all while great sound

and ease of use are on our mind to lead the way.

Your N5 speakers went through Three rounds

Of QC before being packed.

If and at any given time, you have any questions

Or concerns, please feel free to contact us at:

sales@noamaudio.com

Enjoy Your Ride!

esab gnitnuoM

mounting band

rubber insert

Step 2: Hold the speaker in

place where the mounting base

ﬁts the open space of the

mounting band.

Step 1: After choosing the

desired location, place the rubber

insert around the bar while its open

part is at the bottom. Then,

slide the mounting band over the

rubber insert and bar.

follow these instructions to avoid

scratching your bar.

Step 3: Slide the smart handle

screw through the mounting

band and base and screw it

to the Flange nut on the other end.

While opened, turn the smart handle

clockwise.

Step 3.1: Push the smart handle

to a closed position to tight the

mounting band on to the speaker’s

mounting base.

where you can push to close it by hand.

* note: screw the smart handle to a point

ﬁnal tightening can be done easily using

a Wrench. see step 3.2.

Step 3.2: Using a 13mm nut Wrench,

tight the Flange nut for a safe

and secure grip of the speaker to

the bar.

note: after tightening the Flange nut,

it will be impossible to open the

smart handle by hand. Use a nut wrench

to loosen the smart handle’s grip.

Step 4: Setting angle (optional):

Using a Phillips screwdriver to

loosen the 2 screws found on the

speaker’s base will allow you to rotate

the speaker to a desired angle.

After setting the right angle, screw the 2

screws back to ﬁx the angle.

70° Clamp Rotation

Phillips

Screw

‘closed’ position

‘opened’ position

Black SPKR (–)

Red SPKR (+)

Speaker

Wiring

Tower tube

Tower Tube Wiring Detail

12 ft. 2 conductor

speaker wire

Speaker Wiring:

The N5 has a long 12 feet wiring, well protected in a wiring sleeve.

- You can cut the wires to a desired length for a clean installation.

But, make sure to do so only after you ﬁnished installing your entire

audio system, including its ampliﬁer.

- Connect the speaker wires to your ampliﬁer ensuring correct polarity;

Red to positive and Black to negative.

Running your N5 wiring:

Option A: Easiest way to run the N5’s wires would be by running it along and

attached to the Bike’s cage/body all the way to the ampliﬁer’s location.

Use a cable tie to ensure a strong grip of the wires to the Bike’s body.

Option B - Tube wiring: for the cleanest installation, you might want to

choose running the wire’s sleeves through the Bike’s tubes.

If you did choose to drill a hole to run the speaker wire through any location,

be careful not to drill into other wiring or existing mechanisms.

Any time a wire is run through a hole, it is necessary to insert a rubber or

plastic grommet to protect the wire from damage.

Importnt featurs of the N5

Please read before first use

The Smart Handle

The smart handle is a ﬁrst of its kind. we created the smart handle with the ease

of use in mind.

The main purpose of the smart

handle is to allow super fast and

easy installation of the N5 speakers.

The smart handle will allow you to

install the speaker without the need

of using any tools. But, we do

recommend to use a nut wrench

to complete the installation of the N5.

As described later on pages 4 and 5 of this user manual, after closing the

smart handle, a 13mm nut wrench will help you achieving a super strong grip of

the mounting clamp to the bar.

Roll Cage/Bar ﬁtment:

The N5 comes with 4 pairs of rubber

inserts and 2 Aluminum mounting bands.

The mounting system of the N5 is built

to ﬁt 1.5”, 1.75”, 1.85” & 2” bars.

Thus, the N5 will ﬁt most UTV’s models.

* Before installing please measure is your roll cage’s diameter.

Rubber Inserts: Each rubber insert has its intended size written on it.

Band should be used for 1.5” & 1.75” bars while the bigger one should be used

for 1.85” & 2” bars.

The 2 photos on the middle and left shows the right way of installation. After tightening the mounting

band, you should see a gap between the mounting band and the speaker’s mounting base. This gap is

meant to insure a high tension and super strong grip on your roll cage/bar.

If after tightening the mounting bracket, you get a full contact between the mounting band and the

speaker’s mounting base, it means you are probably using the wrong rubber insert size. Please measure

your bar’s diameter and use the right insert size in accordance. Each rubber insert has its intended size

written on it (1.5”/1.75”/1.85”/2”)

Strong And Secure Grip

38.1mm (1.5”) or

44.45mm (.75”) or

46.99mm (1.85”) or

50.8mm (2”)

38.1mm (1.5”) or

44.45mm (.75”) or

46.99mm (1.85”) or

50.8mm (2”)

Mounting Dimensions(enclosure+mounting clamp)

Power Rating: 250 W MAX / 125 W RMS

Sensitivity: 87 dB @ 1W/1M

MidBass: 8” Marine Subwoofer Speaker

Nominal Impedance: 4 ohm

Length: 345mm(13.58”)

Width: 118.1mm/198.8mm(4.65”/7.83”)

Height: 334.8mm/254.1mm(13.18”/10”)

Thank you for choosing NOAM NSUB Marine subwoofer.

We invested a lot of thought, time and eort into

the creation of this subwoofer. all while great sound

and ease of use are on our mind to lead the way.

Your NSUB subwoofer went through Three rounds

Of QC before being packed.

If and at any given time, you have any questions

Or concerns, please feel free to contact us at:

[email protected]

Enjoy Your Ride!

. 1 pcs - NSUB subwoofer

. 1 pcs- Smart handle screw

. 1 pcs- Flange nut

. 1 pcs - of each 1.5”, 1.75”, 1.85” & 2” rubber inserts

. 1 pcs- aluminum mounting bands

mounting band

rubber insert

Mounting base

M8(13mm) WRENCH

Step 2: Hold the speaker in

place where the mounting base

ﬁts the open space of the

mounting band.

Step 3: Slide the smart handle

screw through the mounting

band and base and screw it

to the Flange nut on the other end.

While opened, turn the smart handle

clockwise.

Step 3.2: Using a 13mm nut Wrench,

tight the Flange nut for a safe

and secure grip of the speaker to

the bar.

note: after tightening the Flange nut,

it will be impossible to open the

smart handle by hand. Use a nut wrench

to loosen the smart handle’s grip.

‘closed’ position

‘opened’ position

Step 1: After choosing the

desired location, place the rubber

insert around the bar while its open

part is at the bottom. Then,

slide the mounting band over the

rubber insert and bar.

follow these instructions to avoid

scratching your bar.

Step 3.1: Push the smart handle

to a closed position to tight the

mounting band on to the speaker’s

mounting base.

where you can push to close it by hand.

* note: screw the smart handle to a point

ﬁnal tightening can be done easily using

a Wrench. see step 3.2.

subwooder positioning:

using a Phillips screwdriver, you can

unscrew the mounting base and screw

it back for a monitor position or ﬂat

position.

Best practice:

If you plan to install the NSUB over

your head, we advise to use the ﬂat

mounting position

Flat mounting position

Monitor mounting position

Phillips

Screw

Black SPKR (–)

Red SPKR (+)

Speaker

Wiring

Tower tube

Tower Tube Wiring Detail

12 ft. 2 conductor

speaker wire

Speaker Wiring:

The NSUB has a long 12 feet wiring, well protected in a wiring sleeve.

- You can cut the wires to a desired length for a clean installation.

But, make sure to do so only after you ﬁnished installing your entire

audio system, including its ampliﬁer.

- Connect the speaker wires to your ampliﬁer ensuring correct polarity;

Red to positive and Black to negative.

Running your NSUB wiring:

Option A: Easiest way to run the NSUB’s wires would be by running it along and

attached to the Bike’s cage/body all the way to the ampliﬁer’s location.

Use a cable tie to ensure a strong grip of the wires to the Bike’s body.

Option B - Tube wiring: for the cleanest installation, you might want to

choose running the wire’s sleeves through the Bike’s tubes.

If you did choose to drill a hole to run the speaker wire through any location,

be careful not to drill into other wiring or existing mechanisms.

Any time a wire is run through a hole, it is necessary to insert a rubber or

plastic grommet to protect the wire from damage.

Importnt featurs of the NSUB

Please read before first use

The Smart Handle

The smart handle is a ﬁrst of its kind. we created the smart handle with the ease

of use in mind.

The main purpose of the smart

handle is to allow super fast and

easy installation of the NSUB subwoofer.

The smart handle will allow you to

install the speaker without the need

of using any tools. But, we do

recommend to use a nut wrench

to complete the installation of the NSUB.

As described later on pages 4 and 5 of this user manual, after closing the

smart handle, a 13mm nut wrench will help you achieving a super strong grip of

the mounting clamp to the bar.

Roll Cage/Bar ﬁtment:

The NSUB comes with 4 pairs of rubber

inserts and 2 Aluminum mounting bands.

The mounting system of the NSUB is built

to ﬁt 1.5”, 1.75”, 1.85” & 2” bars.

Thus, the NSUB will ﬁt most UTV’s models.

* Before installing please measure is your roll cage’s diameter.

Rubber Inserts: Each rubber insert has its intended size written on it.

Band should be used for 1.5” & 1.75” bars while the bigger one should be used

Aluminum Band: the NSUB has 2 Aluminum band in 2 dierent sizes. Smaller

for 1.85” & 2” bars.

The 2 photos on the middle and left shows the right way of installation. After tightening the mounting

band, you should see a gap between the mounting band and the speaker’s mounting base. This gap is

meant to insure a high tension and super strong grip on your roll cage/bar.

If after tightening the mounting bracket, you get a full contact between the mounting band and the

speaker’s mounting base, it means you are probably using the wrong rubber insert size. Please measure

your bar’s diameter and use the right insert size in accordance. Each rubber insert has its intended size

written on it (1.5”/1.75”/1.85”/2”)

Strong And Secure Grip

www.noamaudio.com

Visit us at www.noamaudio.com

and sign up to our newsleer to

stay tuned. we are always working

new excing products just for you!

Bluetooth Receiver

Introducon

Installaon

Thank you for choosing NOAM NR

Bluetooth remote controller. We invested

a lot of me and eﬀort planning and

designing the perfect cotroller for your

audio system.

The NR controller went through three

rounds of QC before being packed.

If at any given me you have any

quesons or concerns, please feel free

to contact us at: [email protected]

Enjoy your ride!

NR wires and plugs diagram

Amplifier-Controller DIN plug

Remote In - Blue Wire

The remote-in is an extra feature we added to the NR. Connecting the

remote-in wire to a remote-out wire of another device will allow this

device to trigger your NR ON/OFF.

*note. It’s an optional feature only. You don’t need to use this wire in

order to run your NR.

The NR controller has a DIN

plug. This plug can be connected

directly to the NOAM NA2 & NA4

amplifiers.

Remote power triggering:

The NR is able to power the NA

amplifiers. whenever you turn

the NR ON or OFF the NA2/4

amplifier will do the same.

Aux input - optional

If you already had a peripheral music device on your bike such as satellite

radio, MP3 player or GPS, you will take the audio output from that device

and plug it into the female 1/8” mini plug.

* When not in use, please keep the AUX plug sealed by keeping the

protective cap closed.

Remote In

Aux input

Setup

Pairing bluetooth Deuice

Bluetooth trouble Shoong Guide

AUX Input

Main Key pad Controls

The play pause buon allows you to pause your Bluetooth device from playing. Press

the same buon again and your device will start to play.

The "track up" buon allows you to "skip forward" to the next song saved on your

Bluetooth device. Pressing the "track down" buon once allows you to go back to the

start of the song your’re currently listening to. Press it a second me and go to the start

of the song on your device before the one your’re listening to.

The Volume Up/Volume Down buons will control the volume level of your Tunes, best

pracce: set your audio source’s Volume at around 85% (on your phone, MP3 player

etc) and control the volume using the NR controller

Make sure volume is up on Bluetooth sources

Conﬁrm Pairing if no sound.

Press and hold the AUX/POWER buon for few second to turn the NOAM NR ON. Do

the same to turn it OFF. As menoned above, double tap it to switch between Aux and

Bluetoothmodes.

Go to settings on your phone and place Bluetooth setting into ”discoverable”mode.

Search for (NOAM NR)device.

On phone select (NOAM NR) to pair device.

Once a device is paired each time this device is seen by the NOAM NR it will

outomatically reconnect to the device. If no device is present the NOAM NR

outomatically goes into pairing mode and will present itself as discoverable for the

next device present.

Please Note: Once NOAM NR sees power, it will always try and pair as shown

by the flashing POWER BUTTON. If you do not have a paired device with you

while riding, the light will continue to flash.

Connect AUX Input with any media player(MP3 player, Smartphone, Headunit)

Double tap AUX/Power button rapidly to switch between Bluetooth source and AUX

input source.

When NOAM NR is switchod to AUX input source, the Green LED stays on.

Double tap the AUX/POWER button agian and the Green light will shut off, indicating

the unit is now out of AUX mode. The bluetooth device can now once agian be used

and controlled by the key pad.

Note: When the unit is in AUX mode, the buttons on the control panel do not control

anything to do with the peripheral audio device!

Supplied Hardware

Dash or Flush (Rear) mount

plate

Handlebar mount plate

*not necessary for NUTV5/NUTV5-S models

SS304 Hexagon Socket Head

Screw M6 x 8mm

*not necessary for NUTV5/NUTV5-S models

2 x SS304 Cross Head Screw

M4 x 8mm

Handlebar mount bracket

and pair of rubber rings

*not included in the NUTV5 and NUTV5-S

audio systems

Surface mount plate

Installaon

STEP 1: Slide the NR cables through the

Handlebar mount plate and screw the

plate to the back of the NR, using the 2

M4 cross head screw.

STEP 2: Use the M6 Hexagon socket

head screw to screw the handlebar

bracket to the back of the NR.

For a 7/8'' bar - use the Thick rubber ring

For a 1'' bar - use the Thin rubber ring

For a 1.25'' bar - place the bracket

directly on the bar (no rubber inserts

required).

Handlebar mount: This method

will allow you to mount your NR on

round 7/8'' , 1'' & 1.25'' handlebar.

STEP 2: Peel oﬀ the 3M scker's cover

STEP3: Place the NR on a perfectly ﬂat surface.

Installaon

Mounng yor NOAM NR

The NR controller has 3 mounng opons:

1. Dash or Flush (Rear) mount

2. Surface mount

3. Handlebar mount (not available in the NUTV5 and NUTV5-S units)

Dash or Flush (Rear) mount: This method will

allow the controller to sit ﬂush to the mounng surface.

This requires a perfectly ﬂat surface and ideally should

have access to the rear of the mounng plate.

STEP 1: Slide the NR cables through the Flush

mount plate and screw the plate to the back of

the NR, using the 2 M4 cross head screw.

STEP 2: Using a 2.75'' (70mm) hole saw, drill a

hole in your selected locaon. *Ensure you

have at least 1 inch of clearance on the back

side of your selected mounng locaon.

Surface mount: This method will allow you to

mount the NR on any perfectly ﬂat surface. Using this

method will not require any cung or drilling of the

surface.

STEP 1: Place the NR cables in the rail found on the

inner side of the surface mount plate, and screw

the plate to the back of the NR, using the 2 M4

cross head screw. Then sck the 3M Scker on the

back of the surface mount plate.

STEP 3: Slide the NR through the hole.

STEP 3: Mount the bracket on the handlebar

NOAM NUTV5 User manual

Brand: NOAM

Model: NUTV5

Type: User manual

This manual is also suitable for

NUTV5-S

Download PDF

report

NOAM NUTV5 User manual

This manual is also suitable for

NOAM NUTV5 User manual

Related papers

Other documents