WAGO 8-channel, 24VDC, 0.2 ms/XTR User manual

Brand: WAGO

Model: 8-channel, 24VDC, 0.2 ms/XTR

Type: User manual

Pos: 2 /D ok ument ati on al lg em ein/E inb and /Ei nban d F ro ntsei te - Han dbuc h; C I 20 17; mit Do cVar ia ble n (St an dard) @ 28\mod_1486477502910_0.docx @ 405388 @ @ 1

Manual

WAGO I/O SYSTEM 750 XTR

750-1416/040-000

8DI 24 VDC 0.2ms 2

-wire XTR

-Channel Digital Input; 24 VDC; 0.2 ms;

-Conductor Connection; Extreme

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Rec htlic h es, Allgemeines/Impressum für Standardhandbücher - all g. Anga ben, A nschri ften, Telefo nnum mern und E -Mail-A dres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 4 45 55

Fax: +49 (0) 571/8 87 – 84 45 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO I/O SYSTEM 750 XTR Table of Contents 3

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ............................................................. 5

1.1 Validity of this Documentation................................................................. 5

1.2 Copyright ................................................................................................ 5

1.3 Symbols ................................................................................................. 6

1.4 Number Notation .................................................................................... 7

1.5 Font Conventions ................................................................................... 7

2 Important Notes ........................................................................................ 8

2.1 Legal Bases ............................................................................................ 8

2.1.1 Subject to Changes ............................................................................ 8

2.1.2 Personnel Qualifications .................................................................... 8

2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ....... 8

2.1.4 Technical Condition of Specified Devices........................................... 9

2.1.4.1 Disposal ........................................................................................ 9

2.1.4.1.1 Electrical and Electronic Equipment .......................................... 9

2.1.4.1.2 Packaging ............................................................................... 10

2.2 Safety Advice (Precautions) ................................................................. 11

3 Device Description .................................................................................. 14

3.1 View ..................................................................................................... 16

3.2 Connectors ........................................................................................... 17

3.2.1 Data Contacts/Local Bus .................................................................. 17

3.2.2 Power Jumper Contacts/Field Supply .............................................. 18

3.2.3 Push-in CAGE CLAMP

Connectors ................................................ 19

3.3 Display Elements .................................................................................. 20

3.4 Operating Elements .............................................................................. 20

3.5 Schematic Diagram .............................................................................. 21

3.6 Technical Data ..................................................................................... 22

3.6.1 Device Data ..................................................................................... 22

3.6.2 Power Supply ................................................................................... 22

3.6.3 Communication ................................................................................ 22

3.6.4 Inputs ............................................................................................... 23

3.6.5 Connection Type .............................................................................. 23

3.6.6 Mechanical Conditions ..................................................................... 23

3.6.7 Climatic Environmental Conditions ................................................... 24

3.7 Approvals ............................................................................................. 25

3.8 Standards and Guidelines .................................................................... 26

4 Process Image ......................................................................................... 32

5 Mounting .................................................................................................. 33

5.1 Mounting Sequence .............................................................................. 33

5.2 Inserting and Removing Devices .......................................................... 34

5.2.1 Inserting the I/O Module ................................................................... 34

5.2.2 Removing the I/O Module ................................................................ 35

6 Connect Devices ..................................................................................... 36

6.1 Connecting a Conductor to the Push-in CAGE CLAMP

...................... 36

6.2 Connection Example ............................................................................ 37

4 Table of Contents WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

7 Use in Hazardous Environments ........................................................... 38

7.1 Marking Configuration Examples .......................................................... 39

7.1.1 Marking for Europe According to ATEX and IECEx .......................... 39

7.1.2 Marking for the United States of America (NEC) and Canada

(CEC) ............................................................................................... 43

7.2 Installation Regulations......................................................................... 46

7.2.1 Special Notes including Explosion Protection ................................... 46

7.2.2 Special Notes Regarding ANSI/ISA Ex ............................................ 48

List of Figures .................................................................................................. 49

List of Tables .................................................................................................... 50

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO I/O SYSTEM 750 XTR Notes about this Documentation 5

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 7 /Dokument ation allgemein/Anmerkungen z ur Bearbeitung/! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Dieses Dokument ist nicht freigegeben ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! @ 7\mod_1271240183952_21.docx @ 55090 @ @ 4

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 1/Hi nwei s e zu dies er D o kume ntati on - Über schr ift 1 @ 4\mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Sic her heit s- und sonstige Hinweise/Hinweis/Hinweis : Dokumentation aufbewahren @ 4\mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation

is included, if necessary.

Pos: 10 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/G ült igk eits ber eic h - Ü bers chri ft 2 @ 12\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on ( alt e Str uktur )/ Gül tig keits ber eic h/G ülti g keitsb erei ch D o kume ntat ion I/ O-Modul 750-xxxx, oh ne Vari anten angab e @ 14\mod_1358944037947_21.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-1416/040-000

(8DI 24 VDC 0.2ms 2-wire XTR).

Pos: 12 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on ( alt e Str uktur )/H in weis e/A cht ung: Hi nw eis z ur D o kume ntati on I/O-M odul e 750- xxxx/040-000 @ 27\mod_1468502299549_21.docx @ 216892 @ @ 1

The I/O module 750-1416/040-000 shall only be installed and operated according

to the instructions in this manual, in the system description for the WAGO I/O

SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller.

Consider power layout of the WAGO I/O SYSTEM 750 XTR!

In addition to these operating instructions, you will also need the system

description “Design Notes XTR – Guidelines and Recommendations for

Increasing Operational Safety” and the manual for the used fieldbus

coupler/controller, which can be downloaded at www.wago.com

. There, you can

obtain important information including information on electrical isolation, system

power and supply specifications.

Pos: 13.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Ur heb ersc hut z - Ü bersc hr ift 2 @ 23\ mod_1435647042188_21.docx @ 184808 @ 2 @ 1

1.2 Copyright

Pos: 13.2 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Ur heb ersc hut z au sf ührli ch @ 4\mod_1235565145234_21.docx @ 27691 @ @ 1

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 13.3 /Dokumentation allgemein/Gli eder ungs ele men te/---Sei te nwec hsel--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 13.4 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ S ymbol e - Ü ber schr if t 2 @ 13\ mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 13 .5.1 /Al le Seri en ( All ge mei ne Mo dul e)/ Sich erh eits- und so nsti ge H in weis e/G efa hr/G efa hr: _War nu ng vor P ers on ensc hä den allg emei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 13 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son ensch äden d urch ele ktrisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 10103 0 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 13 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinwei se/W arnung /War nung: _Warn ung vor P erso nensch äden al lgem ein_ - Erläuterung @ 13\mod_1343309877041_21.doc x @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 13 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Vorsic ht/V orsic ht: _War nung vor Pers one nschäd en allg emein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 13 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/A chtu ng/ Ach tung : _ War nung v or Sac hsc h äden allg em ein _ - Er läut eru ng @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 13 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hin weise/ Achtu ng/Ach tung : _Warnu ng vor Sachsc häden durch el ektros tatis che Au fladu ng_ - Erl äuter ung @ 13\ mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 13 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 13 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/I nfor mat ion/ Inf or mati on: _W eiter e I nfor mat ion all ge mein_ - Erl äuter ung @ 13 \mod_1343310439814_21.doc x @ 101051 @ @ 1

WAGO I/O SYSTEM 750 XTR Notes about this Documentation 7

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 13.6 /Dokumentation allge mein/ Gli eder ungs ele ment e/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Pos: 13.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Dar st ellu ng der Z ahl ens yst eme - Über sc hrift 2 @ 2 3\mod_1435647128078_21.docx @ 184811 @ 2 @ 1

1.4 Number Notation

Pos: 13.8 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Za hlens ys te me @ 3\mod_1221059454015_21.doc x @ 21711 @ @ 1

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated

with dots (.)

Pos: 13.9 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Sc hri ftk on venti one n - Ü bersc hri ft 2 @ 23\mod_1435647186005_21.docx @ 184814 @ 2 @ 1

1.5 Font Conventions

Pos: 13.1 0 / Alle Ser ie n (All ge mein e M odul e) /Re chtl ich es, Allg em ein es/Sc hr ift konv enti onen @ 3\mod_1221059521437_21.doc x @ 21714 @ @ 1

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.:

File

New

Input

Designation of input or optional fields are marked in bold letters,

e.g.:

Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.:

[F5]

Pos: 14 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

8 Important Notes WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 15 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/Wi cht ige Erl äu ter unge n - Ü bersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 16.1 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Wi chtig e Er l äuter ung en - Ei nleit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 16.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Rec htl ic he Gr un dlag en - Über schri ft 2 @ 3\mod_1221060626343_21.doc x @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 16.3 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Änd er ungs vor beh alt - Über schr ift 3 und In halt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all

rights arising from the granting of patents or from the legal protection of utility

patents. Third-party products are always mentioned without any reference to

patent rights. Thus, the existence of such rights cannot be excluded.

Pos: 16.4 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/P erson alqu alifi kation/ Pers onalqu alifi katio n 750-xxxx - Ü ber schr ift 3 u nd I nh alt @ 3\ mod_1224061208046 _21.d ocx @ 24 063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO I/O SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM) /Wich tige Er läuter ungen (al te Str ukt ur)/ Besti m mung sge mäß e V erw endu ng/ Bes timm ung sg emäß e V erw end ung 750- xxxx - Überschrift 3 @ 32\mod_1536041141528_21.docx @ 498494 @ 3 @ 1

2.1.3 Use of the 750 Series in Compliance with Underlying

Provisions

Pos: 16.6 /Serie 750 (WAGO-I/O-SYST EM) /Wic htig e Er läut eru nge n (al te Str ukt ur)/B esti m mung sg emäß e Ver w end ung/ Bes ti mmung sg emäß e V er wendu ng 7 50- xxx x für Gerät e - STD - mit EN 61000-6-3 @ 3 \mod_1224064151234_21.docx @ 24070 @ @ 1

Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O

SYSTEM 750 receive digital and analog signals from sensors and transmit them

to actuators or higher-level control systems. Using controllers, the signals can

also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO I/O SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information in

the section “Device Description” > “Standards and Guidelines” in the manual for

the used fieldbus coupler or controller.

WAGO I/O SYSTEM 750 XTR Important Notes 9

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

The implementation of safety functions such as EMERGENCY STOP or safety

door monitoring must only be performed by the F I/O modules within the modular

WAGO I/O SYSTEM 750. Only these safe F I/O modules ensure functional safety

in accordance with the latest international standards. WAGO's interference-free

output modules can be controlled by the safety function.

Pos: 16 .7 /All e Seri en (Allg emei ne M od ule) /R echtl ich es, Allg em ei nes/T ech nisc her Zus ta nd d er Ger äte - Ü bers chr ift 3 u nd I nhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. These

modules contain no parts that can be serviced or repaired by the user. The

following actions will result in the exclusion of liability on the part of WAGO

Kontakttechnik GmbH & Co. KG:

• Repairs,

• Changes to the hardware or software that are not described in the

operating instructions,

• Improper use of the components.

Further details are given in the contractual agreements. Please send your

request for modified and new hardware or software configurations directly to

WAGO Kontakttechnik GmbH & Co. KG.

Pos: null /Al le S eri en ( All gem eine Mo dul e)/Ü bers chr ift en/E b ene 4/En ts orgen - Üb ersc hrift 4 @ 30 \mod_1510145115652_21.docx @ 469859 @ 4 @ 1

2.1.4.1 Disposal

Pos: null /Al le S eri en ( All gem eine Mo dul e)/Ü bers chr ift en/E b ene 5/El ektr o- un d Elekt roni kgerät e - Übers chr ift 5 @ 32\ mod_1537446988068_21.docx @ 501657 @ 5 @ 1

2.1.4.1.1 Electrical and Electronic Equipment

Pos: null /Al le S eri en ( All gem eine Mo dul e)/R ech tli ches , Al lge mei nes/ Ele ktr o- und Ele ktroni kger äte @ 32\mod_1532425086061_21.doc x @ 491989 @ @ 1

Electrical and electronic equipment may not be disposed of

with household waste. This also applies to products without

this symbol.

Electrical and electronic equipment contain materials and substances that can be

harmful to the environment and health. Electrical and electronic equipment must

be disposed of properly after use.

WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary

nationally.

10 Important Notes WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Environmentally friendly disposal benefits health and

protects the environment from harmful substances in

electrical and electronic equipment.

• Observe national and local regulations for the disposal of electrical and

electronic equipment.

• Clear any data stored on the electrical and electronic equipment.

• Remove any added battery or memory card in the electrical and

electronic equipment.

• Have the electrical and electronic equipment sent to your local

collection point.

Improper disposal of electrical and electronic equipment can be harmful to the

environment and human health.

Pos: nul l /Dok umen tatio n allge mein/Gl ieder ungs elem ente/----L eerz eile-( 1Z) ---- @ 28\mod_1485262995837_0.doc x @ 404006 @ @ 1

Pos: null /Al le S eri en ( All gem eine Mo dul e)/Ü bers chr ift en/E b ene 5/Ver pa ckung - Übersc hrift 5 @ 3 2\mod_1537447044202_21.doc x @ 501662 @ 5 @ 1

2.1.4.1.2 Packaging

Pos: null /Al le S eri en ( All gem eine Mo dul e)/R ech tli ches , Al lge mei nes/ Ver pac kung @ 32\mod_1537446786416_21.docx @ 501653 @ @ 1

Packaging contains materials that can be reused.

PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout

Europe. Directives and laws may vary nationally.

Environmentally friendly disposal of the packaging protects the environment and

allows sustainable and efficient use of resources.

• Observe national and local regulations for the disposal of packaging.

• Dispose of packaging of all types that allows a high level of recovery,

reuse and recycling.

Improper disposal of packaging can be harmful to the environment and wastes

valuable resources.

Pos: 16.1 0 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO I/O SYSTEM 750 XTR Important Notes 11

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 16.1 1 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/ Sich erh eits hin weis e - Ü bers chr ift 2 @ 6\mod_1260180299987_21.doc x @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 16.1 2 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/E inl ei tung Sic her heit shi nw eise Har dwar e @ 6\ mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 16.1 3. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : N ich t an G erät en unter S pann ung ar beite n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: null /Al le S eri en ( All gem eine Mo dul e)/ Sich erh eits- und s onstig e Hinw eis e/G efa hr/G efahr : Pr od uk t nur in ein em g eeig net en Geh äuse ei nba uen! @ 33\mod_1543581881435_21.docx @ 511972 @ @ 1

Install device in only one suitable enclosure!

The device is an open system. Install the device in a suitable enclosure. This

enclosure must:

• Guarantee that the max. permissible degree of pollution is not exceeded.

• Offer adequate protection against contact.

• Prevent fire from spreading outside of the enclosure.

• Offer adequate protection against UV irradiation.

• Guarantee mechanical stability

• Restrict access to authorized personnel and may only be opened with tools

Pos: null /Al le S eri en ( All gem eine Mo dul e)/ Sich erh eits- und so nstig e H inw eis e/G efa hr/G efahr : T re nn vorric ht ung und Ü b erstr oms ch utz @ 33\mod_1543915978439_21.docx @ 512267 @ @ 1

Ensure disconnect and overcurrent protection!

The device is intended for installation in automation technology systems.

Disconnect protection is not integrated. Connected systems must be protected by

a fuse.

Provide suitable disconnect and overcurrent protection on the system side!

os: 1 6.13 .4 /All e Ser i en ( Allg emei ne M od ule) /Si cher hei ts- und s ons tig e Hi nwei se/ Ge fahr /Gef ahr : U nfal lver hü tung sv orsc hrif ten beac ht en! @ 6 \mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 16.1 3. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : A uf nor mger ec hte n Ansc hl uss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1

Ensure a standard connection!

To minimize any hazardous situations resulting in personal injury or to avoid

failures in your system, the data and power supply lines shall be installed

according to standards, with careful attention given to ensuring the correct

terminal assignment. Always adhere to the EMC directives applicable to your

application.

Pos: 16.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Warnung/Warnung: Speisung ausschließlich aus SELV-/PELV- Vers org ung ( 24V- XTR-I /O-M odule) @ 29\mod_1493107132163_21.doc x @ 41 961 8 @ @ 1

Power from SELV/PELV power supply only!

All field signals and field supplies connected to this XTR I/O module

(750-1416/040-000) must be powered from SELV/PELV power supply(s)!

Pos: 16.1 5 / Alle Ser ien ( All ge mein e M odul e)/ Sic her heit s- un d s onsti ge Hin wei se/V ors ic ht/Vor sic ht : H eiße Ober fl äche nic ht berü hre n! ( all ge mein) @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1

12 Important Notes WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Do not touch hot surfaces!

The surface of the housing can become hot during operation. If the device was

operated at high ambient temperatures, allow it to cool off before touching it.

Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM) /Wich tige Er läuter ungen (alte Str ukt ur)/Sic her heits- u nd s ons tig e Hi nw eise /Ac htung /Ac ht ung: Ei nwa ndfr eie Kont a ktier ung zur Trag sc hie ne g ew ährl eist en! @ 3 4\mod_1550481407638_21.doc x @ 530599 @ @ 1

Ensure proper contact with the DIN-rail!

Proper electrical contact between the DIN-rail and device is necessary to

maintain the EMC characteristics and function of the device.

Pos: 16.1 6. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : D efe kte oder bes ch ädigt e Ger äte aust ausc hen! @ 6\ mod_1260180857358_21.doc x @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts).

Pos: 16.1 6. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : G erät e vor kriec hen den und isol i ere nden Sto ffen sc hütz en! @ 6\ mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for

handling devices/modules.

Pos: 16.1 6. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : R einig ung nur mi t zul äs sig en M at erial ien! @ 6\mod_1260181203293_21.doc x @ 46751 @ @ 1

Clean only with permitted materials!

Clean housing and soiled contacts with propanol.

Pos: 16.1 6. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755 @ @ 1

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 16.1 6. 6 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : V erpol ung en der Dat en- und V ersorg ungsl eitu ngen ver meide n! @ 6\ mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 16.1 6. 7 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung : El ektr ost atisc h e En tla dung ver mei den! - DIN EN 61340-5-1/-3 @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

WAGO I/O SYSTEM 750 XTR Important Notes 13

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - un d son sti ge Hi n weis e/Ac ht ung/ Ac htung : XT R - Isol atio nsprüf ungen mit DC dur chfü hren! @ 15\mod_1370843209441_21.docx @ 122210 @ @ 1

Use only direct current (DC) for insulation testing!

Both the system voltage and field voltage side are capacitively coupled to the

DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage

between the DIN-rail and at least one of these two potentials can lead to the

destruction of the module.

Use only direct current (DC) for insulation testing. To avoid destroying the I/O

module, you must discharge it completely before applying the test voltage again.

Pos: 17 /D o kume nt ation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

14 Device Description WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 18 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/G erät e besc hrei bung - Ü ber schri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 19.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger ätebesc hrei bung (al te Str uktur )/Einl eitu ng/An wendu ng/DI /Anwe ndung 750-x4xx DI @ 3\mod_1233762736718_21.docx @ 27108 @ @ 1

The digital input module 750-1416/040-000 (8DI 24 VDC 0.2ms 2-wire XTR)

receives control signals from digital field (e.g. of sensors, transmitters, switches

or proximity switches).

Pos: 19.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung/I/ O-Bes chr eibu ng/D I/I /O-Beschreibung 750-141x 8 DI 2-Leiter (DI und 2 4 V) Push-i n C AGE C LAM P @ 15\ mod_1370934995007_21.doc x @ 122344 @ @ 1

The I/O module has 8 input channels, providing a direct connection to 2-wire

sensors.

The sensors are connected to the Push-in CAGE CLAMP

connectors DI 1 and

24 V … DI 8 and 24 V.

Pos: 19.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr ei bung /Allg em ein /Ver weis a uf K api tel " Ans chl üss e" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 19.5 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr eibu ng/D I/I/ O-Beschreibung 750-x4xx DI RC- Filt er 0, 2 ms @ 3\mod_1233755181796_21.docx @ 27083 @ @ 1

Each input channel has a RC noise rejection filter with a time constant of 0.2 ms.

Pos: 19.6 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr eibu ng/D I/I/ O-Beschreibung 750-x4xx DI H SS / p ositivschaltend (24 V) @ 3\mod_1233831724648_21.docx @ 27231 @ @ 1

The I/O module inputs provide high-side switching. If the 24 V potential for field

power is switched to an input connection, the signal status for the corresponding

input channel is set to “high”.

Pos: 19.7 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /LED -Anz eig e/LED Zustan d Signal @ 3\mod_1233755258578_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 19.8 /Serie 750 (WAGO-I/O- SYST EM) /Ger äte bes chr ei bung (alt e S tr uktur )/Ei nlei tu ng/ LED- Anz eige/ Verwei s auf Ka pitel "A nzeig eele mente" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 19.9 /Serie 750 (WAGO-I/O-SYST EM)/ Geräte besc hrei bung (alt e Stru ktur) /Einlei tung /Vers orgu ng/Ver sorg ung 24 V, 0 V üb er Leis tung skont akte St andard @ 3\mod_1226498974531_21.docx @ 25020 @ @ 1

The I/O module 750-1416/040-000 (8DI 24 VDC 0.2ms 2-wire XTR) receives the

24 V voltage supply for the field level from an upstream I/O module or from the

fieldbus coupler/controller via blade-formed power jumper contacts. It then

provides these potentials to subsequent I/O modules via spring-formed power

jumper contacts.

Pos: 19.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Warnung/Warnung: Speisung ausschließlich aus SELV-/PELV- Vers org ung ( 24V- XTR-I /O-M odule) @ 29\mod_1493107132163_21.docx @ 419618 @ @ 1

Power from SELV/PELV power supply only!

All field signals and field supplies connected to this XTR I/O module

(750-1416/040-000) must be powered from SELV/PELV power supply(s)!

Pos: 19.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - un d son sti ge Hi n weis e/Ac ht ung/ Ac htung : M axi maler St ro m Lei stu ngs kont a kte 1 0 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum values via power contacts!

The maximum current that can flow through the power jumper contacts is 10 A.

The power jumper contacts can be damaged and the permissible operating

temperature can be exceeded by higher current values.

When configuring the system, do not exceed the permissible maximum current

value. If there is a higher power requirement, you must use an additional supply

module to provide the field voltage.

Pos: 19.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sons tige H i nweis e/H in wei s/Hi nwei s: Pot enti alei ns peis em odul für Erd e ei nse tze n! ( kei ne L K für Er de) @ 3 \mod_1226499037468_21.docx @ 25023 @ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 15

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 19.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/ Einl eit ung/ Vers org ung /G alva nisc he T re nnu ng F eld/ Sys tem @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 19.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/ Einl eit ung/ Vers org ung /A nordn ung unt er Ber üc ksic htig ung der Leistungskontakte beliebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node.

An arrangement in groups within the group of potentials is not necessary.

Pos: 19.1 5 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Hinweis/Hinweis: XTR - Misc hbetri eb XTR/ Stan dard @ 1 5\mod_1367496420828_21.docx @ 118326 @ @ 1

Mixed operation

Mixed operation (standard/XTR modules) within a node is possible when groups

of modules are electrically isolated on the field side (i.e., electrically isolated

power supply).

Pos: 19.1 6 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (alt e Stru ktur) /Sicher heit s- und sonstige Hinweise/Hinweis/Hinweis: XTR - Erhö hte Stör fes tig keit @ 1 5\mod_1367496424993_21.doc x @ 118330 @ @ 1

Increased interference!

For standard-compliant application in substation instrumentation and control,

telecontrol systems, railway technology or shipbuilding certified operation,

field-side power supply filter 750-624/040-001 or power supply filter

750-626/040-000 are generally to be used for XTR module groups.

Pos: 19.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebes chrei bung (alte Stru ktur) /Einl eitung /Eins atzb ereic h/Eins atzb ereic h 750- xxxx/040-000 all e XTR-K oppl er/ Co ntr oller oh ne Ei nsc hrä nk ung+M isc hb etri eb hinw eise @ 1 5\mod_1368425919479_21.doc x @ 119444 @ @ 1

The I/O module can be operated with all fieldbus couplers/controllers of the

WAGO I/O SYSTEM 750 XTR.

Observe the instructions for mixed operation when used in mixed operation

behind standard fieldbus couplers/controllers.

Pos: 20 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

16 Device Description WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 21 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsi cht - Üb ersc hrif t 2 @ 4 \mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 22 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsi cht/D I/ Ansi cht 75 0-141x_0040-xxxx 8 DI 2-Leiter H SS @ 15\ mod_1369736961941_21.docx @ 120682 @ @ 1

Figure 1: View

Pos: 23 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung (al te Str uktur) /Ansi cht/A nsich t Push-in CageClamp®_Legende mit LEDs @ 15\mod_1370852562803_21.docx @ 122213 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with Mini-

WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

Push-in CAGE CLAMP

connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 24 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 17

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 25 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsc hlüs se - Üb erschr ift 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 26 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /Da ten kont akte /L okal bus - Ü b ersc hrif t 3 @ 6 \mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Local Bus

Pos: 27.1 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (alte Strukt ur)/Anschlüsse/Datenkontakte - Feldbus ko ppler /-c ontr oller u nd M odul e – Abbi ldu ng u nd B esc hrei b ung @ 3\ mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the local bus. The

contacting for the local bus consists of 6 data contacts, which are available as

self-cleaning gold spring contacts.

Figure 2: Data Contacts

Pos: 27.2 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läut erunge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/A chtung/Achtung: I/O- Mod ule nic ht auf Gol dfed erkon takte legen! @ 7\mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM) /Wich tige Er läuter ungen (alte Str ukt ur)/Sic her heits- u nd s ons tig e Hi nw eise /Ac htung /Ac ht ung: ESD - Au f Pote ntiala usgl eich der U mgeb ung acht en! @ 32\ mod_1539077262331_21.docx @ 504433 @ @ 1

Pay attention to potential equalization from the environment!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, please ensure that

environmental factors (personnel, work space and packaging) are properly

equalized. Do not touch any conducting parts, e.g., data contacts.

Pos: 28 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /Lei stu ngs kont a kte/F eld vers org ung - Üb erschr if t 3 @ 6 \mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 30 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Wi cht ige Erl äut eru nge n (al te Str uktur )/Si ch erh eits - un d so nstig e H in weis e/ War nung /War nung : Speis u ng a ussc hli eßlic h aus S E LV-/PE LV-V ers orgu ng ( 24V- XTR- I/O-M odul e) @ 29\ mod_1493107132163_21.docx @ 419618 @ @ 1

Power from SELV/PELV power supply only!

All field signals and field supplies connected to this XTR I/O module

(750-1416/040-000) must be powered from SELV/PELV power supply(s)!

Pos: 31.1 /Serie 750 (WAGO-I/O- SYST EM)/ Wichti ge Erl äuter unge n (alte Str uktur )/Sic herh eits- un d s onsti ge Hin wei se/ Vors ic ht/V orsic ht : Ver le tz ungsg efa hr durc h sc har fk anti ge M esser ko nt akte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury. Do not touch the blade contacts.

Pos: 31.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger ätebesc hrei bung (al te Str uktur )/Ansc hlüs se/Lei stung sko ntakt e 2 LK (Mess er/F eder) - Ei nlei tu ng @ 15\ mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 750-1416/040-000 has 2 self-cleaning power jumper contacts

that supply and transmit power for the field side. The contacts on the left side of

the I/O module are designed as blade contacts and those on the right side as

spring contacts.

Pos: 31.3 /Serie 750 (WAGO-I/O-SYST EM) /Ger ätebesc hrei bung (al te Str uktur )/Ansc hlüs se/Lei stung sko ntakt e 2 LK (Mess er/F eder) - Ab bil dung ( 16-Kanal) @ 15\mod_1370866610582_21.doc x @ 122222 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 31.4 /Serie 750 (WAGO-I/O-SYST EM) /Ger ätebesc hrei bung (al te Str uktur )/Ansc hlüs se/Lei stung sko ntakt e 2 LK (Mess er/F eder) - Legende @ 15\mod_1371721352500_21.docx @ 123710 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 31.5 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: Maximaler Strom Leistungskontakte 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 19

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Do not exceed maximum values via power contacts!

The maximum current that can flow through the power jumper contacts is 10 A.

The power jumper contacts can be damaged and the permissible operating

temperature can be exceeded by higher current values.

When configuring the system, do not exceed the permissible maximum current

value. If there is a higher power requirement, you must use an additional supply

module to provide the field voltage.

Pos: 32 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

Pos: 33 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str uktur )/A nsc hlüs se/P ush- in CAG E C LAM P®-Ansc hlüsse - Üb ersc hrift 3 @ 15 \mod_1370519905692_21.doc x @ 122018 @ 3 @ 1

3.2.3 Push-in CAGE CLAMP

Connectors

Pos: 34 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Wi cht ige Erl äut eru nge n (al te Str uktur )/Si ch erh eits - und sonstige Hinweise/War nu ng/ War nung : S peis ung aus sc hließ lic h au s S ELV- /PEL V-V ersor gu ng (2 4V- XTR-I/ O-Mo dul e) @ 29\mod_1493107132163_21.docx @ 419618 @ @ 1

Power from SELV/PELV power supply only!

All field signals and field supplies connected to this XTR I/O module

(750-1416/040-000) must be powered from SELV/PELV power supply(s)!

Pos: 35 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung (al te Str uktur) /Ansc hlüss e/DI/ Anschl üss e 750-14 1x 8 DI 2-L eiter HS S P ush-i n CA GE C LAM P @ 7\mod_1274262794032_21.docx @ 56626 @ @ 1

Figure 4: Push-in CAGE CLAMP

Connectors

Table 5: Legend for Figure “Push-in CAGE CLAMP

Connectors”

Channel

Designation

Connector

Function

DI 1

Input DI 1: Signal voltage

24 V

Input DI 1: Sensor supply +24 V

DI 2

Input DI 2: Signal voltage

24 V

Input DI 2: Sensor supply +24 V

DI 7

Input DI 7: Signal voltage

24 V

Input DI 7: Sensor supply +24 V

DI 8

Input DI 8: Signal voltage

24 V

Input DI 8: Sensor supply +24 V

20 Device Description WAGO I/O SYSTEM 750 XTR

750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR

Manual

Version 1.1.0

Pos: 36 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

Pos: 37 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nzei g eele ment e - Ü ber schr ift 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 38 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nz eig eele ment e/D I/ Anzei ge elem ente 75 0-141x 8 DI @ 7\mod_1274352179347_21.docx @ 56795 @ @ 1

Figure 5: Display Elements

Table 6: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 State DI 1 1

Off

Input DI 1: Signal voltage (0)

Green

Input DI 1: Signal voltage (1)

8 State DI 8 8

Off

Input DI 8: Signal voltage (0)

Green

Input DI 8: Signal voltage (1)

Pos: 39 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/B edi enel e ment e - Ü bers chri ft 2 @ 4\mod_1239191655456_21.docx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 40 /S eri e 7 50 ( WA GO-I/ O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/B e dienel e ment e/Be di enel eme nte I/O- Modul 75x- xxxx nicht vorhanden @ 4\mod_1236322031125_21.doc x @ 28063 @ @ 1

The I/O module 750-1416/040-000 has no operating elements.

Pos: 41 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

Page is loading ...