2. ROSE DISPLAYS
  3. ANOQUICK ROUND WITH GOTCHA AND MULTICLIPS

ROSE DISPLAYS ANOQUICK ROUND WITH GOTCHA AND MULTICLIPS User manual

  • Hello! I've reviewed the instruction sheet for the AnoQuick™ with Gotcha® Insert system. This document provides step-by-step instructions on how to assemble the poster hanging system using Gotcha Holder, MultiClips, and End Caps. I'm ready to help with any questions you may have about using this product!
  • How do I insert a poster into the Gotcha Holder?
    How do I install the MultiClips?
    How do I remove the Gotcha (and sign)?
Parts
35 Congress Street, Salem MA 01970
Tel# 1-800-631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your way
down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick Holder.
Fig. 2
Step 3
Install MultiClips in the top AnoQuick Holder.
Holding clip at slight angle, first insert one round
end, then press down on other round end and push
MultiClip into holder. Insert second MultiClip.
Fig. 3 & 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder, Gotcha
Holder, End Caps and MultiClips for future projects.
AnoQuick™ with Gotcha
®
Insert
Instructions for Hanging
Incept-9.9.02
The AnoQuickTM is a trademark and Gotcha® is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use of these
products. Part #02INSAnoQuickGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
12A300R
MultiClips
1UP-0100
End Caps
06-5525
Figure 1
Figure 5
Figure 2
Figure 3
Figure 4
Instruction Sheet
Parts
35 Congress Street, Salem MA 01970
Tel# 1-800-631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your way
down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick
Holder. Fig. 2
Step 3
Install MultiClip in the top AnoQuick Holder.
Holding clip at slight angle, first insert one round
end, then press down on other round end and push
MultiClip into holder. Fig. 3
Note: For OneUp applications place the MultiClip
in the center of the AnoQuick Holder. Fig. 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder, Gotcha
Holder, End Caps and MultiClips for future projects.
Instructions for Hanging
Incept-9.9.02
The AnoQuickTM is a trademark and Gotcha® is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use of these
products. Part #02INSAnoQuickGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
12A300R
End Caps
06-5525
MultiClip
1UP-0100
Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
AnoQuick™ with Gotcha
®
Insert
OneUp
®
Instruction Sheet
Parts
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your
way down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick Holder.
Fig. 2
Step 3
Install MultiClips in the top AnoQuick Holder.
Holding clip at slight angle, first insert one round
end, then press down on other round end and push
MultiClip into holder. Insert second MultiClip.
Fig. 3 & 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder, Gotcha
Holder, End Caps and MultiClips for future projects.
Instructions for Hanging
Incept-9.9.02
The AnoQuickTM is a trademark and Gotcha® is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use of these
products. Part #02INSAnoQuickGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
12A300R
End Caps
06-5525
MultiClips
1UP-0100
Figure 1
Figure 5
Figure 2
Figure 3
Figure 4
AnoQuick™ with Gotcha
®
Insert
Instruction Sheet
Parts
Instructions for Hanging
Step 1
Place poster on a flat surface. Snap the Gotcha
Holder open and insert poster (top and bottom).
To close, snap the Gotcha Holder shut. Fig. 1
Note: It is easier to open and close the Gotcha
Holder by starting at one end and working your way
down the holder.
Step 2
Slide the Gotcha Holder into the AnoQuick Holder.
Fig. 2
Step 3
Install MultiClip in the top AnoQuick Holder.
Holding clip at slight angle, first insert one round
end, then press down on other round end and push
MultiClip into holder. Fig. 3
Note: For OneUp applications place the MultiClip
in the center of the AnoQuick Holder. Fig. 4
Step 4
Push end caps into place. Fig. 5
Note: To remove Gotcha (and sign), simply rotate
end cap up out of the way.
Step 5
Suspend poster.
Important note:
Please save and reuse the AnoQuick Holder, Gotcha
Holder, End Caps and MultiClips for future projects.
AnoQuick™ with Gotcha
®
Insert
Instructions for Hanging
Incept-9.9.02
The AnoQuick is a trademark and Gotcha® is a registered trademark of
Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be
held liable for injury, loss or damage resulting from the use of these
products. Part #02INSAnoQuickGotchaMC
Gotcha
®
Special
(no clip rail)
AnoQuick
12A300R
End Caps
06-5525
OneUp
®
Instruction Sheet
MultiClip
1UP-0100
Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
/