RVCGM-80M
Front & Rear Camera Integration Interface for
Select CHEVROLET and BUICK Vehicles with 7” MyLink Systems
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030519
1 of 4
- Adds front and rear camera inputs.
- Front camera automacally shows on the screen aer changing the gear from reverse to drive.
- Programmable front camera delay OFF me using the OSD menu.
PRODUCT FEATURES:
PARTS INCLUDED:
RVCGM-80M Module RVCGM-80M T-Harness LVDS Cable
GVIF Video Cables LVDS Video Extension Board OSD Control Pad
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030519
2 of 4
WIRING DIAGRAM:
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
OEM Monitor
OEM GVIF
Cable
OEM Headunit
GVIF Video Cables
Front Camera Input
Rear Camera Input
To OSD Control Pad
Front/Rear Camera +12V Power
Ground
Green = Rear Camera Manual Trigger*
Blue = Front Camera Manual Trigger*
RVCGM-80M
MODULE
MAIN
*Use these wires if not using CAN Trigger.
Green wire = Connect to Reverse Light +12V
Blue wire = Connect to +12V using a toggle switch
VIDEO
LVDS Video
Extension Board
Red = +12V ACC
Black = Ground
Brown = CAN High
Video Extension Cable
RVCGM-80M
CAN WIRE CONNECTION:
Front & Rear Camera Integration Interface for
Select CHEVROLET and BUICK Vehicles with 7” MyLink Systems
The RVCGM-80M detects the CAN communicaons in the
vehicle. Tap the BROWN wire (GM LAN) on the power harness
to the GREEN wire (PIN# 28) on the 44 pin OEM connector
behind the headunit Reverse gear engagement is automacally
detected and will power on the rear camera. The front camera
will power on when the gear is put to Drive. The delay OFF of
the front camera can be set in the OSD menu. Time delay OFF
can be set from 1 to 60 seconds.
If for some reason the CAN connecon cannot detect the
reverse gear communicaon, connect the GREEN wire on the
RVCGM-80M power harness (Rear Camera Manual Trigger) to
the reverse light wire +12V.
The Front camera also be also be manually triggered by
connecng the BLUE wire (Front Camera Manual Trigger) to
+12V.
GREEN wire Single CAN wire PIN# 28
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030519
3 of 4
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCGM-80M
DIP SWITCH SETTINGS:
OSD Control Pad
The OSD Seng Screen automacally pops up when the OSD Control Pad is connected.
ON SCREEN DISPLAY (OSD) SETTINGS:
Front & Rear Camera Integration Interface for
Select CHEVROLET and BUICK Vehicles with 7” MyLink Systems
Set all DIP switches to OFF (Up).
Use the OSD menu to make the necessary sengs. Remember to Run Save&Reboot aer the sengs are made.
Unplug the OSD Control Pad aer seng the cameras and keep it in a secure locaon in case it is needed to change
the sengs.
REAR CAMERA SETTING
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030519
4 of 4
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCGM-80M
VEHICLE APPLICATIONS:
Compable with 7” MyLink Systems
CHEVROLET
2013 - 2015
2013 - 2015
2012 - 2015
2013 - 2015
2013 - 2015
Camaro
Cruze
Equinox
Malibu
Volt
Front & Rear Camera Integration Interface for
Select CHEVROLET and BUICK Vehicles with 7” MyLink Systems
BUICK
2012 - 2015
2013 - 2015
LaCrosse
Verano
FRONT CAMERA SETTING
The front Camera will automacally show on the screen when the gear is put to Drive from Reverse. Delay OFF me
can be set from 1 to 60 seconds aer a pung the car to drive from reverse. See seng image above.
2015 Camaro Radio
2015 Malibu Radio
/
