EP2C6212D16NM
Quick Installation Guide
www.asrockrack.com
No. Description
1 USB 3.0 Ports (USB3_1_2)
2 LAN RJ-45 Port (IPMI_LAN1)
3 VGA Port (VGA1)
4 UID Switch (UID)
4
2
P/N: 15G065099000AK V1.0
Install the Server Board
Motherboard Layout
Jumper Cap On/O
The server board User's Manual is available for download from the ASRock Rack's ofcial website
at http://www.asrockrack.com.
Take note of the following precautions before you install server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place your
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag
that comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
1
1
Insert the server board into the chassis.
2
Affix the screws clockwise into the
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
When the jumper cap is placed on the pins, the
jumper is “Short”. If no jumper cap is placed on the
pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when a jumper cap is placed on
these 2 pins.
I/O Panel
33.02 cm (13 in)
VGA1
USB 3.0
T: USB2
B: USB1
DDR4_A2 (64 bit, 288-pin module, White)
DDR4_A1 (64 bit, 288-pin module, Blue)
DDR4_B1 (64 bit, 288-pin module, Blue)
DDR4_C1 (64 bit, 288-pin module, Blue)
Intel
C622
DDR4_F1 (64 bit, 288-pin module, Blue)
DDR4_E1 (64 bit, 288-pin module, Blue)
DDR4_D1 (64 bit, 288-pin module, Blue)
DDR4_D2 (64 bit, 288-pin module, White)
DDR4_L1 (64 bit, 288-pin module, Blue)
DDR4_K1 (64 bit, 288-pin module ), Blue
DDR4_J1 (64 bit, 288-pin module), Blue
DDR4_J2 (64 bit, 288-pin module), White
DDR4_G2 (64 bit, 288-pin module, White)
DDR4_G1 (64 bit, 288-pin module, Blue)
DDR4_H1 (64 bit, 288-pin module, Blue)
DDR4_I1 (64 bit, 288-pin module, Blue)
RoHS
IPMI_LAN
ATX 12V1
1
HDLED RESET
PLED PWRBTN
PANEL1
1
1
AUX_PANEL1
SPEAKER
BATTERY1
PCIE7
(White)
PCIE6
(Blue)
Dr.
Debug
52
1
FRNT_VGA1
M2_1
11
ATX 12V2
12
18
20
21
22
29
28
REAR_FAN1
REAR_FAN2
CPU1_FAN1
FRNT_FAN1
FRNT_FAN2
FRNT_FAN3
FRNT_FAN4
CPU2_FAN1
1
USB3_3_4
USB3_5
1
1
1
TPM1
1
NMI_BTN1
OCU1
OCU2
MEZZ_MB_A2
1
1
1
1
1
MEZZ_MB_B2
MEZZ_MB_A1
MEZZ_MB_B1
MEZZ_1_C1
BMC
Super
I/O
1
FRONT_LED_LAN34
UID1
SSATA_0_3
SATA_0_7
SSATA_4
ATXPWR1
1
PSU_SMB1
1
1
1
1
1
PMBUS_SEL_DAT1
PMBUS_SEL_ALT1
SATAPWR1
NCSI_SEL1
BIOS
ROM
12
3
4
5
6
710
BMC_SMB_1
IPMB_1
CHASSIS_ID2
CHASSIS_ID1
CHASSIS_ID0
ME_RECOVERY1
T 1
R
NUT30 NUT42 NUT60 NUT80
89
13
14
15
16
17
19
23
24
25
26
27
30
313233343536373839404142
44
43
45
46
47
48
49
56
57
EP2C622D16NM
CPU2
CPU1
30.5 cm (12 in)
1
PECI1
53
PMBUS_SEL_CLK1
55
54
51
50
3
1 Mini-SAS HD Connector (SSATA_0_3)
2 Mini-SAS HD Connector (SATA_0_7)
3 PMBUS Mode Jumper (PMBUS_SEL_ALT1)
4 SATA DOM Power Jumper (SATAPWR1)
5 SATA DOM Connector, Red (SSATA_4)
6 PMBUS Mode Jumper (PMBUS_SEL_CLK1)
7 NCSI Mode Jumper (NCSI_SEL1)
8 ATX Power Connector (ATXPWR1)
9 PSU SMBus (PSU_SMB1)
10 PMBUS Mode Jumper (PMBUS_SEL_DAT1)
11
3 x 288-pin DDR4 DIMM Slots
(DDR4_A1, DDR4_B1, DDR4_C1, Blue)*
12 1 x 288-pin DDR4 DIMM Slots (DDR4_A2, White)
13 ATX 12V Power Connector (ATX12V1)
14 LGA 3647 CPU Socket P0 (CPU1)
15 Rear Fan Connector (REAR_FAN1)
16 Rear Fan Connector (REAR_FAN2)
17 CPU1 Fan Connector (CPU1_FAN1)
18 1 x 288-pin DDR4 DIMM Slots (DDR4_D2, White)
19
3 x 288-pin DDR4 DIMM Slots
(DDR4_D1, DDR4_E1, DDR4_F1, Blue)*
20
3 x 288-pin DDR4 DIMM Slots
(DDR4_G1, DDR4_H1, DDR4_I1, Blue)*
21 1 x 288-pin DDR4 DIMM Slots (DDR4_G2, White)
22 Front Fan Connector (FRNT_FAN1)
23 Front Fan Connector (FRNT_FAN2)
24 Front Fan Connector (FRNT_FAN3)
25 LGA 3647 CPU Socket P0 (CPU2)
26 Front Fan Connector (FRNT_FAN4)
27 CPU2 Fan Connector (CPU2_FAN1)
28 ATX 12V Power Connector (ATX12V2)
29 1 x 288-pin DDR4 DIMM Slots (DDR4_J2, White)
30
3 x 288-pin DDR4 DIMM Slots
(DDR4_J1, DDR4_K1, DDR4_L1, Blue)
31 OCuLink x4 Connector (OCU2)
32 OCuLink x4 Connector (OCU1)
33 Non Maskable Interrupt Button (NMI_BTN1)
34 Speaker Header (SPEAKER1)
35 System Panel Header (PANEL1)
36 Auxiliary Panel Header (AUX_PANEL1)
37 ermal Sensor Header (TR1)
38 TPM Header (TPM1)
39 Intelligent Platform Management Bus header (IPMB1)
40 Chassis ID1 Jumper (CHASSIS_ID1)
41 BMC SMBus Header (BMC_SMB_1)
42 Vertical Type A USB 3.0 (USB3_5)
43 BMC SMBus Header 1 (BMC_SMB1)
44 Chassis ID2 Jumper (CHASSIS_ID2)
45 Chassis ID0 Jumper (CHASSIS_ID0)
46 Mezzanine Slot (MEZZ_MB_A2)*
47 ME Recovery Jumper (ME_RECOVERY1)
48 CPU PECI Mode Jumper (PECI1)
49 Mezzanine Slot (MEZZ_MB_B2)*
50 M.2 Slot (M2_2)
51 PCI Express 3.0 Slot (PCIE6)
52 PCI Express 3.0 Slot (PCIE7)
53 Mezzanine Slot (MEZZ_MB_A1)
54 Mezzanine Slot (MEZZ_1_C1)
55 Mezzanine Slot (MEZZ_MB_B1)
56 Front LAN LED Header (FRONT_LED_LAN34)
57 Front VGA Header (FRONT_VGA1)
*Only supports ASRockRack storage cards.
3
4
1
2
System Panel
Auxiliary Panel
5 Headers
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
GND
SMB_CLK
SMB_Alert
CASEOPEN
1
SMB_DATA
+3VSB
LAN1_LINK
LED_PWR
LAN2_LINK
LED_PWR
+5VSB
GND
GND
LOCATORLED1+
LOCATORLED1-
LOCATORBTN#
System Fault LED-
A
B
C
D
System Fault LED+
E
*15G065099000AK*
EP2C6212D16NM
Quick Installation Guide
www.asrockrack.com
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M bps connection or no
link
Blinking Yellow Data Activity Yellow 100M bps connection
On Link Green 1G bps connection
8 LAN Port LED Indications
6
7
Remove the CPU socket cover. Align and
install the processor on the carrier.
Carefully ip the carrier assembly. Apply
a thermal paste .
en install the heatsink to the carrier
assembly and make sure the arrow is
located in the correct direction.
CPU_
FAN
Install the heatsink. Tighten the screws in a sequential order (6-1>6-2>6-3>6-4). When
dissembling the heatsink, loosen the screws in reverse order (6-4>6-3>6-2>6-1). Connect
the CPU fan to the CPU FAN connector.
Install the Power Cables
10
Install the PCIE Card
1
Remove the bracket facing the slot that
you intend to use. Keep the screw for
later use.
2
Align the card connector with t he
slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with the
screw.
3
IPMI LAN Port
ACT/LINK LED
SPEED LED
LAN Port
Install the Processor and Heatsink
Dr. Debug
11
1
3V
3V
GND
GND
5V
5V
GND
PWROK_PS
5VSB
12V
12V
3V
3V
-12V
GND
PSON#
GND
GND
GND
5V
5V
5V
GND
N/A
12
24 13
4
8
1
5
+12V2
GND
4
8
1
5
+12V2
GND
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
1
2
PIN1
CPU Carrier
3
4
180
o
5
6
Tighten the two
Middle Nuts to
12 IN.LB.
Two turns at a time.
Tighten the two
Corner Plunger
to 12 IN.LB.
Tw
o turns at a time.
6-1
6-2
6-3
6-4
Guide Pin
Guide Pin
*Images shown are for illustrative purposes only and may dier depending on model.
9
Install the Memory
1
2
3
Unlock a DIMM slot by
pressing the module clip
outward.
Insert the memory module. Lock the clip.
Recommended Memory Congurations
Code Description
00 Please check if the CPU is installed correctly and then clear CMOS.
0d
Problem related to memory, VGA card or other devices. Please clear CMOS, re-install the memo-
ry and VGA card, and remove other USB, PCI devices.
01 - 54
(except 0d),
5A- 60
Problem related to memory. Please re-install the CPU and memory then clear CMOS. If the
problem still exists, please install only one memory module or try using other memory modules.
55
e Memory could not be detected. Please re-install the memory and CPU. If the problem still
exists, please install only one memory module or try using other memory modules.
61 - 91 Chipset initialization error. Please press reset or clear CMOS.
92 - 99
Problem related to PCI-E devices. Please re-install PCI-E devices or try installing them in other
slots. If the problem still exists, please remove all PCI-E devices or try using another VGA card.
A0 - A7
Problem related to IDE or SATA devices. Please re-install IDE and SATA devices. If the problem
still exists, please clear CMOS and try removing all SATA devices.
b0
Problem related to memory. Please re-install the CPU and memory. If the problem still exists,
please install only one memory module or try using other memory modules.
b4 Problem related to USB devices. Please try removing all USB devices.
b7
Problem related to memory. Please re-install the CPU and memory then clear CMOS. If the
problem still exists, please install only one memory module or try using other memory modules.
d6
e VGA could not be recognized. Please clear CMOS and try re-installing the VGA card. If the
problem still exists, please try installing the VGA card in other slots or use other VGA cards.
d7
e Keyboard and mouse could not be recognized. Please try re-installing the keyboard and
mouse.
d8 Invalid Password.
FF Please check if the CPU is installed correctly and then clear CMOS.
12
Dr. Debug
1 CPU Conguration
CPU1
A1 A2 B1 C1 D1 D2 E1 F1
1 DIMM
#
2 DIMMS
# #
4 DIMMS
# # # #
6 DIMMS
# # # # # #
8 DIMMS
# # # # # # # #
2 CPU Conguration
CPU1
A1 A2 B1 C1 D1 D2 E1 F1
1 DIMM
#
2 DIMMS
#
4 DIMMS
# #
8 DIMMS
# # # #
16 DIMMS
# # # # # # # #
CPU2
G1 G2 H1 I1 J1 J2 K1 L1
1 DIMM
2 DIMMS
#
4 DIMMS
# #
8 DIMMS
# # # #
16 DIMMS
# # # # # # # #
Note: "#" indicates the socket is populated with a memory module.
/