FH- C612N M
Quick Installation Guide
www.asrockrack.com
No. Description No. Description
1 USB 3.0 Ports (USB3_1_2) 4 Serial Port (COM1)
2 LAN RJ-45 Port (IPMI_LAN1) 5 UID Switch (UID)
3VGA Port (VGA1)
4
2
P/N: 15G065054100AK V1.0
Install the Server Board
Motherboard Layout
Jumper Cap On/O
The server board User's Manual is available for download from the ASRock Rack's ofcial website
at http://www.asrockrack.com.
Take note of the following precautions before you install server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place your
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag
that comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
1
1Insert the server board into the chassis.
2Affix the screws clockwise into the
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
When the jumper cap is placed on the pins, the
jumper is “Short”. If no jumper cap is placed on the
pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when a jumper cap is placed on
these 2 pins.
I/O Panel
33.02 cm (13 in)
ATXPWR1
VGA1
USB 3.0
T: USB2
B: USB1
DDR4_B2 (64 bit, 288-pin module, White)
DDR4_B1 (64 bit, 288-pin module, Blue)
DDR4_A2 (64 bit, 288-pin module, White)
DDR4_A1 (64 bit, 288-pin module, Blue)
1
FH-C612NM
Intel
C612
DDR4_C1 (64 bit, 288-pin module, Blue)
DDR4_C2 (64 bit, 288-pin module, White)
DDR4_D1 (64 bit, 288-pin module, Blue)
DDR4_D2 (64 bit, 288-pin module, White)
DDR4_G1 (64 bit, 288-pin module, Blue)
DDR4_G2 (64 bit, 288-pin module ), White
DDR4_H1 (64 bit, 288-pin module ), Blue
DDR4_H2 (64 bit, 288-pin module ), White
DDR4_F2 (64 bit, 288-pin module, White)
DDR4_F1 (64 bit, 288-pin module, Blue)
DDR4_E2 (64 bit, 288-pin module, White)
DDR4_E1 (64 bit, 288-pin module, Blue)
RoHS
IPMI_LAN
MEZZ1
IPMB1
1
ATX12V1
1
1
1
CPU1
CPU2
1
HDLED RESET
PLED PWRBTN
PANEL1
1
1
AUX_PANEL1
USB_1_2 USB3_3_4
SPEAKER
PSU_SMB1
1
1
BATTERY1
BUZZER1
1
SATA_0
SATA_M0
SATA_1
SATA_M1
SSATA_0_3
TPM1
PCIE7
(White)
COM1
PCIE6
(Blue)
Dr.
Debug
BMC_SMB1
1
11 1
ME_RECOVERY1
CHASSIS_ID2
CHASSIS_ID1
PECI1
23456 7891011 12
51
52
1
PMBUS_SEL_CLK1
PMBUS_SEL_DAT1
PMBUS_SEL_ALT1
1
1
SATA_SGPIO2
SATA_SGPIO1
BMC_SMB2
1
T 1R
Super
I/O
BMC
1
1
CHASSIS_ID3
SATA_2_5
UID1
MEZZ2
1
BIOS_SEL1
1
NMI_BTN1
1
J100
CLRMOS1
1
FRONT_VGA1
USB3_5
BIOS
ROM
A
BIOS
ROM
B
NUT1
NUT2NUT3NUT4
M2_2
NUT5
13
34353637384042 39
41
43
4445464748
49
50
53
54
55
56
57
FRNT_FAN 5
FRNT_FAN 4
FRNT_FAN3
CPU1_FAN1
ATX12V2
FRNT_FAN1
CPU2_FAN1
FRNT_FAN2
FRNT_FAN6
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
31
No. Description
1 SATA SGPIO Connector 1 (SATA_SGPIO1)
2PSU SMBus (PSU_SMB1)
3 USB 2.0 Header (USB_1_2)
4 ATX Power Connector (ATXPWR1)
5 Vertical Type A USB 3.0 (USB3_5)
6 USB 3.0 Header (USB3_3_4)
7 Mini-SAS Connector (SATA_2_5)
8 Mini-SAS Connector (SSATA_0_3)
9 SATA3 Connector (SATA_0)
10 SATA3 Connector (SATA_M0)
11 SATA3 Connector (SATA_1)
12 SATA3 Connector (SATA_M1)
13 CPU PECI Mode Jumper (PECI1)
14 2 x 288-pin DDR4 DIMM Slots
(DDR4_A1, DDR4_B1, Blue)
15 Front Fan Connector (FRNT_FAN5)
16 2 x 288-pin DDR4 DIMM Slots
(DDR4_A2, DDR4_B2, White)
17 Front Fan Connector (FRNT_FAN4)
18 ATX 12V Power Connector (ATX12V1)
19 LGA 2011 CPU Socket R3 (Narrow ILM) (CPU1)
20 CPU1 Fan Connector (CPU1_FAN1)
21 Front Fan Connector (FRNT_FAN3)
22 2 x 288-pin DDR4 DIMM Slots
(DDR4_C2, DDR4_D2, White)
23 2 x 288-pin DDR4 DIMM Slots
(DDR4_C1, DDR4_D1, Blue)
24 2 x 288-pin DDR4 DIMM Slots
(DDR4_E1, DDR4_F1, Blue)
25 2 x 288-pin DDR4 DIMM Slots
(DDR4_E2, DDR4_F2, White)
26 Front Fan Connector (FRNT_FAN2)
27 Front Fan Connector (FRNT_FAN1)
28 Front Fan Connector (FRNT_FAN6)
29 CPU2 Fan Connector (CPU2_FAN1)
30 LGA 2011 CPU Socket R3 (Narrow ILM) (CPU2)
31 ATX 12V Power Connector (ATX12V2)
32 2 x 288-pin DDR4 DIMM Slots
(DDR4_H2, DDR4_G2, White)
33 2 x 288-pin DDR4 DIMM Slots
(DDR4_H1, DDR4_G1, Blue)
34 System Panel Header (PANEL1)
35 Speaker Header (SPEAKER1)
36 Auxiliary Panel Header (AUX_PANEL1)
37 TPM Header (TPM1)
38 ermal Sensor Header (TR1)
39 Descriptor Security Override Jumper (J100)
40 ME Recovery Jumper (ME_RECOVERY1)
41 Non Maskable Interrupt Button (NMI_BTN1)
42 Chassis ID2 Jumper (CHASSIS_ID2)
43 Chassis ID3 Jumper (CHASSIS_ID3)
44 Chassis ID1 Jumper (CHASSIS_ID1)
45 BIOS Selection Jumper (BIOS_SEL1)
46 Intelligent Platform Management Bus header (IPMB1)
47 BMC SMBus Header 1 (BMC_SMB1)
48 BMC SMBus Header 2 (BMC_SMB2)
49 Mezzanine Slot 2 (MEZZ2)
50 M.2 Slot (M2_2)
51 Mezzanine Slot 1 (MEZZ1)
52 SATA SGPIO Connector 2 (SATA_SGPIO2)
53 PMBUS Mode Jumper (PMBUS_SEL_DAT1)
54 Clear CMOS Pad (CLRMOS1)
55 PMBUS Mode Jumper (PMBUS_SEL_CLK1)
56 PMBUS Mode Jumper (PMBUS_SEL_ALT1)
57 Front VGA Header (FRONT_VGA1)
35
4
1
2
*15G065054100AK*
3
FH- C612N M
Quick Installation Guide
www.asrockrack.com
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M bps connection or no
link
Blinking Yellow Data Activity Yellow 100M bps connection
On Link Green 1G bps connection
8LAN Port LED Indications
Dr. Debug
5
7
11
6
123
Open the socket levers and the
CPU socket cover.
Install the processor and close
the socket cover.
Close the socket levers. Remove
the CPU protection cap.
Install the CPU Fan and Heatsink
CPU_FAN
12
Apply the thermal grease. Install the
CPU fan and heatsink and secure
the screws.
Connect the CPU fan to the CPU
FAN connector.
Install the Memory
Install the Power Cables
123
Unlock a DIMM slot by
pressing the module clips
outward.
Insert the memory module. Lock the clips.
10 Install the PCIE Card
1Remove the bracket facing the slot that
you intend to use. Keep the screw for
later use.
2Align the card connector wit h the
slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with the
screw.
3
IPMI LAN Port
System Panel Auxiliary Panel
12 Headers
9
A
B
A
B
A
B
A
B
B
A
Install the Processor
ACT/LINK LED
SPEED LED
LAN Port
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
GND
SMB_CLK
SMB_Alert
CASEOPEN
1
SMB_DATA
+3VSB
LAN1_LINK
LED_PWR
LAN2_LINK
LED_PWR
+5VSB
GND
GND
LOCATORLED1+
LOCATORLED1-
LOCATORBTN#
System Fault LED-
AB
CD
System Fault LED+
E
1
3V
3V
GND
GND
5V
5V
GND
PWROK_PS
5VSB
12V
12V
3V
3V
-12V
GND
PSON#
GND
GND
GND
5V
5V
5V
GND
N/A
12
24 13
4
8
1
5
+12V2
GND
Code Description
00 Please check if the CPU is installed correctly and then clear CMOS.
0d Problem related to memory, VGA card or other devices. Please clear CMOS, re-install the memo-
ry and VGA card, and remove other USB, PCI devices.
01 - 54
(except 0d),
5A- 60
Problem related to memory. Please re-install the CPU and memory then clear CMOS. If the
problem still exists, please install only one memory module or try using other memory modules.
55 e Memory could not be detected. Please re-install the memory and CPU. If the problem still
exists, please install only one memory module or try using other memory modules.
61 - 91 Chipset initialization error. Please press reset or clear CMOS.
92 - 99 Problem related to PCI-E devices. Please re-install PCI-E devices or try installing them in other
slots. If the problem still exists, please remove all PCI-E devices or try using another VGA card.
A0 - A7 Problem related to IDE or SATA devices. Please re-install IDE and SATA devices. If the problem
still exists, please clear CMOS and try removing all SATA devices.
b0 Problem related to memory. Please re-install the CPU and memory. If the problem still exists,
please install only one memory module or try using other memory modules.
b4 Problem related to USB devices. Please try removing all USB devices.
b7 Problem related to memory. Please re-install the CPU and memory then clear CMOS. If the
problem still exists, please install only one memory module or try using other memory modules.
d6 e VGA could not be recognized. Please clear CMOS and try re-installing the VGA card. If the
problem still exists, please try installing the VGA card in other slots or use other VGA cards.
d7 e Keyboard and mouse could not be recognized. Please try re-installing the keyboard and
mouse.
d8 Invalid Password.
FF Please check if the CPU is installed correctly and then clear CMOS.
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ASRock Rack EP2C612D16C-4L Installation guide
-
-
ASRock Rack EP2C612D16SM User manual
-
-
ASRock Rack EP2C612D16FM-N Quick Installation Manual
-
-
-
-
-
Other documents
-
ASROCK EP2C612D16FM Installation guide
-
Gigabyte TRX40 DESIGNARE Owner's manual
-
-
-
-
-
ASROCK X99 WS-E Installation guide
-
Advantech ASMB-786 User manual
-
AIC Auriga User manual
-