Super Bright LEDS EZD-RGBW3-WM User manual

EZD-RGBW3-WM
Super Bright LEDS
Brand
Super Bright LEDS
Model
EZD-RGBW3-WM
Type
User manual

Super Bright LEDS EZD-RGBW3-WM is a wireless LED RGBW 3-zone wall switch compatible with EZ Dimmer Series Controllers. It features precise synchronization between controllers in one zone, allowing for multi-zone control. With its user-friendly interface, you can easily control the brightness, color, and power of your LED lights. The wall switch has a built-in color wheel for selecting and fine-tuning the desired color, as well as dedicated buttons for adjusting the intensity of red, green, blue, and white channels.

Super Bright LEDS EZD-RGBW3-WM is a wireless LED RGBW 3-zone wall switch compatible with EZ Dimmer Series Controllers. It features precise synchronization between controllers in one zone, allowing for multi-zone control. With its user-friendly interface, you can easily control the brightness, color, and power of your LED lights. The wall switch has a built-in color wheel for selecting and fine-tuning the desired color, as well as dedicated buttons for adjusting the intensity of red, green, blue, and white channels.

Important: Read all instructions prior to installation.
Wireless LED RGBW 3-Zone Wall Switch
for EZ Dimmer Series Controllers
1 - RGB 3-Zone LED Dimmer Wall Switch
2 - Mounting Screws
Parts Included
Pairing Controller
1. Pairing Switch
To Pair Wall Switch to Controller, push once and then
push Wall switch. Lights will blink once to indicate linking.
To unpair Wall Switch(es), push and hold until lights blink
twice.
2. Master/Slave Jumper
Set Jumper to Master for main Controller. Master emits
synchronization signal to Slave Controllers. Set Jumper
to Slave to receive synchronization signal from Master
Controller. Use Master for the rst Controller in each zone.
To achieve precise synchronization between Controllers in
one zone, set additional Controllers to slave.
EZD-4C8A Controller
EZD-RGBW3-WM
DC INPUT
OUTPUT
V+
V-
V+
R-
G-
B-
W
12/36VDC
Pairing
Switch
MASTER SLAVE
DC INPUT
OUTPUT
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
Pairing
Switch
MASTER SLAVE
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-RGBW3-WM Remote
Operating Voltage 12~24 VDC
Operating Frequency 868 MHz
FCC ID# 2ACUQ2820
EZD-4C8A Controller
Input Voltage Current Output Wattage
12~36 VDC 4 X 8A 384W(12V) 768W(24V)
1152W(36V)
1
1
2
2
Safety
Set-Up Instructions
Remote
1. Follow illustrated steps below to connect Wall Switch to Power Supply. Connect GND
terminal to negative and connect VIn to positive from power supply.
Controller
1. Make sure power to the Controller is disconnected.
2. Using a small athead screwdriver, loosen the labeled terminal screws visible on the top of
the controller.
3. Matching light strip wires with labeled slots on the Controller, insert wires and tighten
terminal screws. Be sure wire conductor, not wire insulation, is secured in terminal.
4. Turn power on and wait until light strip illuminates. If it does not come on, check light strips
and wiring connections.
• DO NOT install with power applied to controller or switch.
• DO NOT expose the Wall Switch or Controller to moisture.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation. Any changes
or modications in construction of this device which are not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Wall Switch Instructions
1. Release Wall Switch control panel from Back Plate
by separating at notch on bottom of Wall Switch and
pivoting away from locking tabs on top of Wall Switch.
2. Connect the wiring from the Wall Switch to the Power
Supply as the diagram shown to the right. Optionally,
connect wired DMX control signal to DMX controllers.
3. Fasten wall switch to existing switch box using
supplied Screws.
4. Align locking tabs on top of Wall Switch Control Panel
to Back Plate and pivot Control panel towards Back
Plate being sure all locking tabs engage fully.
Back of EZD-RGBW3-WM
Power Supply
Power Supply
Wireless RF Control
EZD-4C8A
12-24VDC
GND Vi n D- D+ GND
DC INPUT
OUTPUT
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
Pairing
Switch
MASTER SLAVE
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
DC INPUT
OUTPUT
V+
V-
V+
R-
G-
B-
W
12/36VDC
Pairing
Switch
MASTER SLAVE
DC INPUT
OUTPUT
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
Pairing
Switch
MASTER SLAVE
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
Common Anode Output (+)
Channel 2 Output (-)
Channel 1 Output (-)
Channel 3 Output (-)
(+)
(-)
Channel 4 Output (-)
Pairing Switch
Master/Slave
Jumper
Power In
EZD-4C8A Controller
Connection Diagram
User Manual
EZD-RGBW3-WM
with EZD-4C8A controller
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 07/01/2021
Important: Read all instructions prior to installation.
User Manual
EZD-RGBW3-WM
with EZD-4C8A controller
Multi-zone Diagram
Note: Multi-zone control will only work with wireless control setup.
Wireless LED RGBW 3-Zone Wall Switch for EZ Dimmer Series Controllers
EZD-4C8A
ZONE 1
ZONE 2
ZONE 3
DC INPUT
OUTPUT
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
Pairing
Switch
MASTER SLAVE
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
Power Supply
EZD-4C8A
Power Supply
DC INPUT
OUTPUT
V+
V-
V+
12/36VDC
Pairing
Switch
MASTER SLAVE
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
CH1
CH2
CH3
CH4
DC INPUT
OUTPUT
V+
V-
V+
12/36VDC
Pairing
Switch
MASTER SLAVE
EZD-4C8A
PRI:
Uin=12-36VDC
lin=8.3A
SEC:
Uout=1x(12-36)VDC
Iout=4x8A
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
CH1
CH2
CH3
CH4
Power Supply
W B R G V+
W
B
R
G
+
W
B
R
G
+
W
B
R
G
+
W
B
R
G
+
W
B
R
G
+
B R G V+
NFLS-RGB150X2-WHT-LC4
B
R
G
+
B
R
G
+
B
R
G
+
B
R
G
+
B
R
G
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
EZD-4C8A
Wireless
RF Control
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 07/01/2021
Important: Read all instructions prior to installation.
Remote Functions
Wireless LED RGBW 3-Zone Wall Switch
for EZ Dimmer Series Controllers
*Wake From Sleep - Remote goes to sleep after 15
seconds. Wake remote by pressing any button then
controls are active.
LED Indicator -
Illuminates Blue when Wall Switch is active. Tap Master
On/Off until Indicator is Blue. Controls are now active.
Illuminates Red when system is off.
Red Blue
Brightness Buttons -
Increases or decreases
intensity of the active zone.
Does not control white
channel(s)
Zone Buttons - Single
press initiates control of
that zone. Press and hold
individual zone button to
turn on or off that zone.
Play/Pause Button - Single
press to initiate color
changing modes(10). Single
press to pause color
changing mode. Single
press again to select the
next color changing. Press
and hold to adjust tempo of
color changing modes.
Master On/Off - Toggles
power to all zone. Retains
all settings on power toggle.
RGB White Button - Selects
or adds RGB natural white,
cool white or warm white of
the active zone.
White Button - Single press
turns on or off white LEDs of
the active zone. Press and
hold to adjust white intensity
of the active zone.
Blue Button - Single press
turns on or off blue LEDs of
the active zone. Press and
hold to adjust blue intensity
of the active zone.
Red Button - Single press
turns on or off red LEDs of
the active zone. Press and
hold to adjust red intensity
of the active zone.
Green Button - Single press
turns on or off green LEDs of
the active zone. Press and
hold to adjust green intensity
of the active zone.
Color Wheel - Directly select
color from any mode by
rotating finger around to
fine-tune desired color.
User Manual
EZD-RGBW3-WM
with EZD-4C8A controller
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1 07/01/2021
  • Page 1 1
  • Page 2 2
  • Page 3 3

Super Bright LEDS EZD-RGBW3-WM User manual

EZD-RGBW3-WM
Super Bright LEDS
Brand
Super Bright LEDS
Model
EZD-RGBW3-WM
Type
User manual

Super Bright LEDS EZD-RGBW3-WM is a wireless LED RGBW 3-zone wall switch compatible with EZ Dimmer Series Controllers. It features precise synchronization between controllers in one zone, allowing for multi-zone control. With its user-friendly interface, you can easily control the brightness, color, and power of your LED lights. The wall switch has a built-in color wheel for selecting and fine-tuning the desired color, as well as dedicated buttons for adjusting the intensity of red, green, blue, and white channels.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents