super bright LED MWPE Series User manual

Brand: super bright LED

Model: MWPE Series

Type: User manual

The super bright LED MWPE Series LED Teardrop Mini Wall Pack with Emergency Backup is a versatile and powerful lighting solution for both indoor and outdoor applications. With its IP65 environmental rating, it can withstand harsh weather conditions, making it ideal for use in areas such as parking lots, walkways, and building facades. The MWPE Series also features a CCT selection switch, allowing you to choose between 3500K, 4000K, and 5000K color temperatures to match your specific lighting needs.

LED Teardrop Mini Wall Pack with Emergency Backup

Important: Read all instructions prior to installation. MWPE Series

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Rev Date: V2 07/14/2022

5yr

User Manual

Specications

Safety and Notes

Wiring Diagram

CCT Selection

Line

Neutral

Ground

Black

L L

Line Blue

L L

N N

GND GND

White

Dim (+)

Dim (-)

Purple

+ +

- -

Gray/Pink

Yellow / Green

• Product should be installed and serviced by in accordance with applicable

national, state, and local building and electrical codes.

• To reduce the risk of electric shock, ensure that the main power source and

circuit breakers are switched o before performing any installation or wiring

procedures.

• Avoid looking directly into lamp when illuminated.

• Ensure all mounts are securely attached and will support the weight of the

xture. Failure to properly support xture may result in damage or injury, for

which the manufacturer does not assume responsibility.

• Photocell sensor can be disabled by unplugging it and capping the connector

that was attached to the sensor.

• Do not connect emergency battery until all other possible mounting and wiring

are complete. Make certain supply power is o when initially connecting the

emergency battery.

• Emergency battery requires at least 24 hours of charge time between uses

or before initial testing.

To select CCT, open the wall pack and use internal switch

to set the desired color temperature. This process should

be done prior during installation. If adjustment is needed

after installation, make certain to remove supply power

before opening the wall pack or making any changes.

Model MWPE-SW15WD-BRP

Ambient Operating Temperature 32°–113° F (0°–45° C)

Environmental Rating IP65

Dimming 0–10 V

Photocell Operation Light will turn on when the ambient light level falls below 30 lx

and will turn o when the ambient light level exceeds 130 lx.

Check product label for specific electrical

specifications related to installation.

Improper installation will void warranty.

120–277 VAC Input

0–10 V Dimming

3500K 4000K 5000K

LED Teardrop Mini Wall Pack with Emergency Backup

Important: Read all instructions prior to installation. MWPE Series

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Rev Date: V2 07/14/2022

5yr

User Manual

Installation

1. Remove screw covers and screws and

separate front and rear housings.

Note: There will be two electrical connectors

that connect the front and rear, which will

need to be disconnected once the xture

is open as well.

2. Select desired CCT value on internal switch.

3. Drill holes in rear housing for mounting, and

remove plug for wiring.

4. Mount rear housing to junction box/wall,

making certain to use the included gasket.

5. With supply power o, connect supply wiring.

6. Connect the plugs for the emergency battery.

7. Reconnect electrical plug running from front

to rear housing and reattach front housing

to rear housing.

8. Once secure, apply power and check for

proper operation.

Note: Emergency operation test button is at

the bottom of the xture. Fixture will need to

charge for 24 hours before initial test.

super bright LED MWPE Series User manual

super bright LED MWPE Series User manual

super bright LED MWPE Series User manual

Related papers

Other documents