Extron electronics TLE 710 User manual

Brand: Extron electronics

Model: TLE 710

Type: User manual

This manual is also suitable for

68-2117-01 Rev. A

12 11

TLP 710CV

User Guide

TouchLink

™

7" Cable Cubby

TouchLink

™

Touchpanel

This symbol is intended to alert the user of important operating and

maintenance (servicing) instructions in the literature provided with the

equipment.

This symbol is intended to alert the user of the presence of uninsulated

dangerous voltage within the product enclosure that may present a risk of

electric shock.

Caution

Read Instructions • Read and understand all safety and operating instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future reference.

Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment

manufacturer because they may be hazardous.

Warning

Power sources • This equipment should be operated only from the power source indicated on the product. This

equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third

(grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of the

equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by

items placed upon or against them.

Servicing • Refer all servicing to qualiﬁed service personnel. There are no user-serviceable parts inside. To prevent

the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may

expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent

overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions of

the manufacturer.

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le

matériel contient des instructions importantes concernant l’exploitation et la

maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier

de l’appareil de tensions dangereuses non isolées posant des risques

d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant d’utiliser

le matériel.

Conserver les instructions• Ranger les consignes de sécurité aﬁn de pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou

présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de ﬁxation ni d’outils non recommandés par le fabricant

du matériel car cela risquerait de poser certains dangers.

Avertissement

Alimentations • Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce

matériel doit être utilisé avec une alimentation principale comportant un ﬁl de terre (neutre). Le troisième

contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la

désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons

d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de

la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne

risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien

qualiﬁé. Aucun des éléments internes ne peut être réparé par l’utilisateur. Aﬁn d’éviter tout danger

d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le

retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des oriﬁces, ceux-ci servent à empêcher les

composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d’explosion s’il y a remplacment incorrect de la batterie. Remplacer uniquement

avec une batterie du meme type ou d’un type equivalent recommande par le constructeur. Mettre au reut les

batteries usagees conformement aux instructions du fabricant.

Safety Instructions • English

Consignes de Sécurité • Français

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen

Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung

(Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren

des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind

und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und

Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie

aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der

Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom Hersteller

empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.

Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter

konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht

umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der

Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose

ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand

darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualiziertem Servicepersonal durchgeführt werden. Die

internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen

Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines

elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur

Vermeidung einer Überhitzung der empndlichen Teile im Inneren. Diese Öffnungen dürfen niemals von

anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien nur

durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen

Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Este símbolo se utiliza para advertir al usuario sobre instrucciones

importantes de operación y mantenimiento (o cambio de partes) que se

desean destacar en el contenido de la documentación suministrada con los

equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de

elementos con voltaje peligroso sin protección aislante, que puedan

encontrarse dentro de la caja o alojamiento del producto, y que puedan

representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el

equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la

documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especiﬁcamente recomendados

por el fabricante, ya que podrian implicar riesgos.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica

indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución

general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no

puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica

al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el

módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde

no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calicado. En el interior no

hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la

reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes

peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o oriﬁcios en su caja/alojamiento, es para evitar el

sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros

objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta batería

únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas

siguiendo las instrucciones del fabricante.

Instrucciones de seguridad • Español

安全须知 • 中文

这个符号提示用户该设备用户手册中有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。

注意

阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。

保存说明书 • 用户应保存安全说明书以备将来使用。

遵守警告 • 用户应遵守产品和用户指南上的所有安全和操作说明。

避免追加 • 不要使用该产品厂商没有推荐的工具或追加设备，以避免危险。

警告

电源 • 该设备只能使用产品上标明的电源。设备必须使用有地线的供电系统供电。第三条线（

地线）是安全设施，不能不用或跳过。

拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后或桌面电源的电源线，或任何接到市电

系统的电源线。

电源线保护 • 妥善布线，避免被踩踏，或重物挤压。

维护 • 所有维修必须由认证的维修人员进行。设备内部没有用户可以更换的零件。为避免出现触

电危险不要自己试图打开设备盖子维修该设备。

通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止机内敏感元件过热。不要用任何东西

挡住通风孔。

锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按

照生产厂的建议处理废弃电池。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the user guide, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at his own expense.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit

to ensure compliance with FCC emissions limits.

For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and

related topics, click here.

Conventions Used in this Guide

In this user guide, the following are used:

CAUTION: A caution indicates a potential hazard to equipment or data.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

WARNING: A warning warns of things or actions that might cause injury, death, or other

severe consequences.

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1& * X2) * X2# * X2!

}

NOTE: For commands and examples of computer or device responses mentioned in

this guide, the character “0” is used for the number zero and “O” represents

the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and ﬁeld names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

Contents

Introduction ............................................ 1

About This Guide ............................................. 1

About the TLP 710CV ...................................... 1

Features ........................................................... 1

Application Diagram ........................................ 2

Requirements ................................................... 3

Hardware and Software ............................... 3

Other Hardware ........................................... 3

Installation Overview ............................. 4

Planning ...................................................... 4

Mounting the TLP 710CV ............................ 4

Preparing and Installing the AAP Assembly .. 4

Connecting the Touchpanel ........................ 4

Mounting ................................................. 5

Planning .......................................................... 5

Tools Required for Installation .......................... 6

Included Parts .................................................. 6

Cutting the Table ............................................. 7

Cutout Dimensions ...................................... 7

Cutting the Surface ...................................... 7

Running Cables................................................ 8

Installing Cable Retractors (Optional) ................ 8

Installing the Power Modules ........................... 8

Preparing and Installing the AAP Assemblies .... 9

Installing AAPs ............................................. 9

Inserting the AAP Assemblies ..................... 10

Mounting the TLP 710CV Enclosure ............... 11

Touchpanel Features and Connectors ...12

Front Panel .................................................... 12

TLP 710CV Connectors .................................. 14

MTP input .................................................. 14

Network and Power over

Ethernet Connector .................................. 15

Power Connector ....................................... 16

Conguration and Calibration

Overview ................................................17

Screen Conﬁguration and Calibration ............ 17

Installing Software and Firmware ................... 17

Designing the Screen Layout .......................... 17

Linking Control Functions to Screen Objects .. 17

Initial Conguration and Calibration ..18

How to Access the Internal

On-screen Menus .......................................... 18

Main Screen ................................................... 18

Volume Screen ............................................... 19

Time Screen ................................................... 20

Network Screen ............................................. 20

Video Screen .................................................. 21

Touch Calibration Screen ................................ 21

Conguration Software ........................22

The Conﬁguration Software ........................... 22

Installing the Software ................................... 22

GUI Congurator and Global Congurator

Installation ................................................ 22

Using the TouchLink touchpanel Web Pages ... 23

Updating the Firmware .................................. 25

Updating Firmware Using Extron Firmware

Loader ...................................................... 25

Updating Firmware Using

GUI Congurator ...................................... 26

Updating Firmware From a Web Browser ... 27

Using GUI Congurator ................................. 28

Using Global Congurator ............................. 33

Specications .........................................38

Accessories and Part Numbers ..............42

Included Parts ................................................ 42

Optional Parts ................................................ 42

Reset Modes ...........................................43

TLP 710CV • Contents v

TLP 710CV • Contents vi

Introduction

z About This Guide

z About the TLP 710CV

z Features

z Requirements

About This Guide

This guide describes the function, installation, conguration, and operation of the TLP 710CV

touchpanel controllers.

In this guide the terms TLP 710CV and touchpanel refer to the TLP 710CV.

About the TLP 710CV

The Extron TLP 710CV 7-inch Cable Cubby

TouchLink

™

touchpanel is fully conﬁgurable

and combines the AV system control of TLP 710 touchpanels with the cable management

convenience of the Cable Cubby. It features a tilt-up, full-color touchscreen in an elegant, metal

enclosure that can be mounted securely into a tabletop, lectern, or other ﬂat surface.

Global Congurator and GUI Congurator software, along with ready-to-use templates, make

system setup fast and easy, with no programming knowledge required. An integrated Ethernet

port provides communication with IP Link

enabled control processors for controlling and

monitoring AV equipment such as projectors, displays, switchers, and source devices over a

standard Ethernet network.

The Cable Cubby has room for 11 single Architectural Adapter Plates (AAPs). AV connectivity

and cable management is provided by convenient pullout cables such as VGA, 3.5 mm audio,

AV, network, HDMI, DVI, and Display port cables. Passive AAP plates and a dual AC outlet are

also available.

Using the video input, the touchpanel can monitor video source devices either as a preview aid

or as a personal viewer for the operator.

Features

7 inch LCD screen — has 800x480 resolution and displays a wide range of customizable text

and graphics.

Touch screen overlay — provides simple and intuitive control over a range of functions by

touching on-screen icons.

Video source monitoring — accepts S-video or composite video through a connection to an

Extron MTP transmitter and provides a preview of the video signal.

Power over Ethernet (PoE) — a twisted pair cable carries network information and 48 VDC

from the PoE power supply to the touchpanel.

Compatible with most Extron IP Link products — allows easy integration into existing

systems.

Built-in speaker — provides audible feedback when a button is pressed.

TLP 710CV • Introduction 1

Light sensor — allows the auto dimming feature to adjust LCD screen backlighting to take

account of ambient lighting.

Lid switch — when the lid is opened the LCD screen, light sensor, and illuminating LED are all

activated. When the lid is closed, these features are deactivated to save energy. The speaker is

always active, whether the lid is open or closed.

Sleep mode — conserves power when no button presses are detected for a user-determined

period of time. When a user touches the screen, the touchpanel is reactivated.

Space for at least 11 AAPs — Provides AV connectivity through passive or pass-through

AAPs. Depending on the model, there are dual AC outlets which may be US, European Union,

or International. Models are also available with no AC outlets.

Compatible with Extron Cable Retractors — allows cable management.

Two ﬁnish options — the trim ring and lid are available in black anodized or brushed

aluminium to match room decor.

Application Diagram

Extron

RGB 580xi

Interface

Extron

IPL 250

IP Link Ethernet

Control Processor

TCP/IP

Network

Mounted

Through a Table

or Podium

Video

Extron

TLP 710CV

7" Cable Cubby

TouchLink Touchpanel

Extron

Video

DVD

Figure 1. Typical Application for the TLP 710CV

TLP 710CV • Introduction 2

Requirements

Hardware and Software

The latest system requirements for running the conﬁguration software can be found on the

Extron website:

z GUI Conﬁgurator

z Global Conﬁgurator

Other Hardware

An Extron IP Link control interface must also be connected to the same network domain as the

TouchLink touchpanel. Suggested models include:

z IPL T S series (for example IPL T S4)

z IPL 250

z IPL T CR48

z IPL T SFI244

z IPCP series

See the Extron website (www.extron.com) for further information about these products.

TLP 710CV • Introduction 3

Installation

Overview

This section provides an overview of the main steps required to install the TLP 710CV and

provides links to more detailed explanations of each step.

You can also visit the TouchLink

touchpanel site at www.extron.com/touchlink for further assistance in the setup and

operation of the TLP 710CV, or to enroll in online training. For additional assistance,

contact your nearest Extron ofﬁce.

The instructions provided in this guide are for experienced installers. To avoid damaging the

furniture, Extron recommends that the opening in the table for the TLP 710CV should be cut

only by a licensed and bonded craftsperson.

Planning

 Decide what the system requires and ensure that there is enough space for all the

components of the system.

 Collect the tools needed to complete the installation.

 Open the shipping container and verify that all the components are present.

Mounting the TLP 710CV

 Decide how to cut the hole and obtain the proper cutout dimensions or a router

template.

 Cut a hole in the furniture.

Preparing and Installing the AAP Assembly

 Run but do not connect the cables for the AAPs and TLP 710CV.

 Install cable retractors, if required.

 If required, install the power module.

 Install AAPs. Loosely fasten all AAPs to the AAP assembly and install cables.

 Install the AAP assembly into the Cable Cubby enclosure and tighten all AAPs.

 Mount and secure the TLP 710CV frame into the furniture opening.

Connecting the Touchpanel

 Connect the TLP to the PoE power supply and connect the power supply to a network

router.

NOTE: Extron recommends using the PoE power supply (provided). Alternatively, it is

possible to connect a 12 VDC power supply (not provided).

(Optional) If you are not using PoE, mount and connect a 12 VDC power supply to

the TLP 710CV and connect the TLP 710CV directly to a network router.

 (Optional) For the video monitoring capabilities, connect the MTP transmitter input.

TLP 710CV • Installation Overview 4

Mounting

This section provides detailed instructions for mounting the TLP 710CV in a table and installing

the AAPs. It covers:

z Planning

z Tools Required for Installation

z Included Parts

z Cutting the Table

z Mounting the TLP 710CV Enclosure

z Running Cables

z Installing Cable Retractors

z Installing Power Modules

z Preparing and Installing the AAP Assemblies

Planning

Before making any cuts, select the best location for the TLP 710CV. Keep in mind the following:

 Ensure that the edge that opens on the lid is oriented correctly.

 Ensure there is enough space for all the system cables and components, above and below

the table. Take account of:

z Clearances for under-table cabling, especially if the cable has a large bend radius.

z Adequate space below the table for cable retractors if they are to be installed.

z The number and type of AAPs required for the installation.

z The location of devices that connect to the AAPs either above or below the table.

 Verify that you have the correct template or dimensions.

 Decide on the method for cutting a hole in the table. There are three methods available:

z Hand router and template, which requires a router template (part number

70-980-01), which must be purchased separately

z CNC wood router, which must be programmed with the correct dimensions.

z Jigsaw, which requires a paper template (available from the Extron website).

The hand router using the routing template or the CNC wood router are the most accurate

methods for cutting the hole. Either one of these methods is recommended by Extron. The

jigsaw is less accurate but is also acceptable.

 Check all relevant regulations.

z Ensure the installation complies with local, state, and national building and electrical

codes.

z Ensure the installation complies with the Americans with Disabilities Act or other

accessibility requirements.

TLP 710CV • Mounting 5

Tools Required for Installation

The following tools are required but not supplied:

Safety Glasses

Phillips Screw Driver

Tape Measure

1/4" Hex Nut Driver

Marking Pen

Square

Vacuum Cleaner

Included Parts

Open the shipping container and verify that all the components are present:

Table Clamps

Extron

Removal Tool

Zip Ties

#4−40 Screws

and Nuts

TLP 710CV

AC Power Module

Blank AAPs

Pass-thru AAPs

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

PWR LAN OUT LAN-IN

AMBER

GREEN

BLINK

POWER ON

POWER ACTIVE

LOAD ERROR

Power over

Ethernet (PoE)

Injector

Extron

With Power Module Without Power Module

AC Power Module

1 0

Pass-through AAPs

2,3

3 3

Blank AAPs 6 6

1 space Bracket Kit 0 1

2 space Bracket Kit 3 4

3 space Bracket Kit 1 1

NOTES:

Outside the US, see the Extron website to purchase a power module that is

suitable for your location.

Each AAP Bracket Kit consists of two brackets. The rear bracket is higher than

the front bracket and has two holes for screws.

Active or Passive AAPs are not provided and must be purchased separately (see

the Extron website).

Single-space brackets can only be installed in one location (see the note and

ﬁgure on page 9).

TLP 710CV • Mounting 6

Cutting the Table

Cutout Dimensions

CAUTIONS: • The table should be cut only by licensed and bonded craftspeople.

• Make certain the correct cutout dimensions are being used before proceeding

to the next step. Extron is not responsible for incorrectly cut mounting holes.

• The surfaces of the Cable Cubby enclosure have screws and other protruding

hardware that could damage fine furniture. Do not rest the enclosure on

unprotected furniture.

• Ensure the table surface is at least 0.375 inches (0.95 cm) thick.

There are three alternative methods of making the hole for the TLP 710CV:

z If using a hand router, you should purchase the TLP 710CV routing template (part number

70-980-01).

z If using a CNC wood router, use the exact cut-out dimensions (see below).

z If using a reciprocating saw or jigsaw use the paper cut-out template.

Cutting the Surface

WARNING: To avoid eye injury, wear safety glasses when operating power equipment.

Be certain the cut is laid out in exactly the desired location and the edge that opens on the lid

is correctly oriented. After verifying and checking dimensions, cut a hole in the surface of the

furniture where the enclosure will be installed.

Router with Routing Template

If using a routing template, make

sure it is the correct template for the

TLP 710CV (part number 70-980-01).

For complete instructions, see the

Routing Template User Guide, available at

www.extron.com.

NOTE: The metal router guide must be purchased

separately. It is reusable and should not be

discarded when the installation is complete.

CNC Router

If using a CNC router, enter the correct dimensions for the TLP 710CV:

8.90 +0.00/-0.02 inches W x 7.1 +0.00/-0.02 inches D

22.61 +0.00/-0.05 cm W x 18.03 +0.00/-0.05 cm D

NOTE: The width dimension (underlined) refers to the

side with AAP access.

Reciprocating Saw or Jigsaw

If using a reciprocating saw or jigsaw, make

sure to use the paper cutout template for the

TLP 710CV. The template is available on the

Extron website (www.extron.com).

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

USER ACCESS

Cut-Out Template for the Extron

TLP 710CV

Outer Edge of Trim Ring

(Do not cut this line.)

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Mark the position on the wall or

furniture where the TLP 710MV

is being installed.

4. Cut the opening.

P/N 68-2046-01 Rev. B

Page size: 11" x 17"

Print scale 1:1

Do not shrink.

P/N

TLP 710CV • Mounting 7

Running Cables

Run all cables necessary to support the AC connector, the cables stored in the cubby, and all

planned AAP connectors. Run the cables below the table and through the hole that was cut

in the previous step (“Cutting the Surface”). Leave enough slack in the cables to connect or

route them before the cubby is installed in the table. Leave enough slack for the external power

supply and to connect AV cables and the cable for PoE and LAN to the TLP 710CV.

Installing Cable Retractors (Optional)

Extron cable retractors retract and store extended cables in Cable Cubby systems, preventing

them from tangling underneath the table. Retractor kits are available for several cable types.

Up to six retractors can be installed in the TLP 710CV enclosure (three on either end). They are

not provided with the TLP 710CV and must be purchased separately.

The buttons on the retractors must be placed at one end of the unit and must, therefore, be

the ﬁrst or the last items added. For complete information and installation instructions, see the

Retractors User Guide, which is available from the Extron web site (www.extron.com).

Installing the Power Modules

WARNINGS: • Switch off all electrical power before connecting the AC conduit to a

junction box, and keep power off until installation is complete.

• If the power cable is installed next to the retractors, ensure the power

cable cannot get tangled in the cable retractor mechanism.

CAUTION: All electrical installation must be performed by qualiﬁed personnel in

accordance with local and national electrical codes.

NOTE: Different countries require different power adapters. For models that do not

include a power module, see the Extron website to select a power module that is

suitable for your location.

The power module takes up two or three AAP spaces and may be installed before or after the

AAP assembly is installed or, if desired, with AAPs on either side.

1. Secure the power module into position with #4-40 Phillips head screws and star washers.

WARNINGS: To ensure good electrical grounding, you must use the star washers with

the screws.

Secure the power module

to the TLP 710CV frame

with #4-40 Phillips head

screws and star washers.

Figure 2. Installing the power modules

TLP 710CV • Mounting 8

2. Run the cable or conduit to a convenient junction box. Extron recommends the circuit be

attached to a junction box that is directly wired to the main circuit. The AC power module

does not have a fuse.

Preparing and Installing the AAP Assemblies

The AAP assembly organizes the AAPs onto a frame that can easily be inserted or removed

from the TLP 710CV frame. Pass-through and blank AAP plates are provided with the

TLP 710CV. Active or passive AAPs must be purchased separately. For the complete range of

available AAPs, see the Extron website.

If neither power modules nor cable retractors are installed, up to 11 AAPs can be

accommodated. Cable retractors, if installed, occupy the space of two AAP slots. The power

modules occupy the space of two (US) or three (European or Universal) AAP slots.

AAP brackets are available in one-space, two-space, and three-space conﬁgurations. Decide the

location of each AAP prior to assembly. Pass-through AAPs provide direct cable connection and

must have the cable installed as they are being mounted on the brackets.

TIP: The recommended way to install the cables and AAPs is to populate the brackets with

AAP plates outside the enclosure as shown below, then install the populated AAP

assemblies into the enclosure.

NOTE: An extra column of AAP bracket mounting points is

available for use with TLP Single-space AAP mounting

brackets (part number 70-693-01). Single-space

brackets will not ﬁt in any other location.

Rear Brackets

Front Brackets

Figure 3. Preparing the AAP Assembly

Installing AAPs

1. Determine how many AAPs will be used and how many front and rear brackets will be

needed. The brackets come in one-space, two-space, and three-space conﬁgurations. The

rear brackets are taller than the front brackets.

2. Place the AAP onto the bracket. Ensure one end of the AAP is secured to a front bracket

and the other end is secured to a rear bracket. Whenever possible match the width of the

front and rear brackets.

NOTES: • Active, passive and pass-through AAPs can be mixed.

• Cables can be attached to the active or passive AAPs after assembly.

• Insert cables into each pass-through AAP before the next AAP is added.

The extra column

of mounting points

is for installing

single-space

AAP brackets.

TLP 710CV • Mounting 9

3. Attach the AAP loosely to the bracket with the supplied #4-40 captive washer nuts.

NOTE: At this time, captive washer nuts should be hand tightened otherwise it is

difcult to attach the brackets to the frame of the TLP 710CV (see “Inserting

the AAP Assemblies” below).

4. When using pass-through AAPs, ensure they are in the correct orientation with the

opening in the grommet facing forward (see ﬁgure 4).

5. Insert one cable through the opening of each grommet. Cables can only be inserted into

the pass-through AAP while the front edge is exposed. Securing the next AAP in place

closes the opening on the previous AAP and ensures that the cable cannot escape.

6. Add AAPs until the bracket is ﬁlled. Spaces that are not required can be ﬁlled with a blank

AAP.

Inserting the AAP Assemblies

1. From under the table, push the ﬁrst AAP assembly through the bottom of the enclosure.

The holes in the rear bracket must align with the bottom row of holes on the rear

face of the enclosure.

If necessary, pull any pass-through cables out of the way.

COMPUTER

AUDIO

Phillips Head Screws

(secure AAP

Assembly)

Tighten down

AAP Nuts.

Push assembly through

bottom of enclosure.

Large slot

provides tool

access to fasten

rear brackets.

Figure 4. Inserting the AAP Assemblies

2. Insert a long screwdriver through the large slot in the front panel and secure the rear

bracket to the rear face of the enclosure with the provided #4-40 Phillips head screws.

3. Secure the front bracket to the front face of the enclosure, using the provided #4-40

Phillips head screws.

TLP 710CV • Mounting 10

4. Use a hex nut wrench to tighten the AAP captive washer nuts.

NOTE: When the AAP assembly was initially prepared, the nuts were hand tightened

(see the previous section, “Installing AAPs”). If they are tightened more

securely, at that stage, it is difﬁcult to align the brackets with the screw holes

on the enclosure.

5. Repeat steps 1 through 4 to add the next AAP assembly, until all the assemblies have been

inserted into the enclosure.

6. Run cables to connect the source and output devices to the active and passive AAPs.

Mounting the TLP 710CV Enclosure

WARNING: The ﬂanged edges of the trim ring are sharp. Exercise caution when the

cubby is not installed in a table to prevent personal injury.

CAUTION: The trim ring edges are soft and can easily be nicked or bent. Exercise

caution when handling and mounting the enclosure.

1. Remove the edge grommet protecting the corners of the trim ring and the plastic ﬁlm on

the ﬁnished surfaces.

CAUTION: Do not use isopropyl alcohol or other solvents to clean the Cable Cubby.

Strong solvents will ruin some ﬁnishes.

2. Carefully lower the TLP 710CV enclosure into the hole cut in the table (see “Cutting the

Table” on page 7). Ensure the trim ring is ush with the top of the table.

3. Under the table, attach the table clamp bodies (

) to the pins on each side of the

TLP 710CV. If necessary, loosen the wingnuts (

) and the Phillips head screws (

4. When the clamps are properly seated on the pins, tighten the Phillips head screws until the

clamp faces (

) are tightly secured against the bottom of the table.

5. To prevent the screws from becoming loose, secure the wingnuts against the table clamp

bodies.

Figure 5. Mounting the TLP 710CV Enclosure

TLP 710CV • Mounting 11

Touchpanel

Features and

Connectors

This section discusses the features and connectors of the TLP 710CV touchpanel.

Front Panel

With the lid down, the light sensor (

in ﬁgure 7), the screen (

), and illumination LED (

)

are disabled. All three activated by opening the lid.

With the lid open, remove the front panel bezel, as shown in gure 6, using the Extron removal

tool.

Extron

Insert the removal tool in the

slot at one top corner and

loosen the bezel away from

the screen.

Move the removal tool to

the second slot and

loosen the bezel away from

the screen.

Slide the removal tool along

one side until the bezel

separates from the unit.

Figure 6. Removing the Bezel

TLP 710CV • Touchpanel Features and Connectors 12

Figure 7. TLP 710CV Front Panel with Bezel Removed

Light Sensor — mounted on top of the screen. The sensor monitors the level of ambient

light and adjusts the screen brightness.

b LCD screen — has a 800x480 resolution with a touch overlay. Extron software is used to

design and conﬁgure a graphic user interface to display buttons, text, or icons, which have

user-deﬁned functions associated with them.

Three MTP Signal Adjustments — available for S-video luminance gain (VID/Y), S-video

chrominance gain (C), and sharpness (S). For composite video signals, the gain is controlled

by the VID/Y adjustment.

Reset LED — provides feedback about the reset status when the user presses the reset

button (see “Reset Modes” on page 43).

Controller Communication LED — unlit during normal operation. Blinks red if the

connection to the IP Link controller is lost.

Reset Button — allows the unit to be reset in

any of four different modes (see “Reset Modes”

on page 43).

Menu Button — activates the on-screen menus

for calibrating the unit (see “Initial Calibration”

on page 18).

Loudspeaker — provides audible feedback (see

the ﬁgure to the right).

i Slots — insert Extron removal tool to separate the

bezel from the screen.

j Illumination LED — lights the interior of the

cable cubby compartment.

TLP 710CV • Touchpanel Features and Connectors 13

TLP 710CV Connectors

The rear panel of the TLP 710CV has a compartment that can be accessed from beneath the

unit. This compartment contains the connectors for power, LAN and PoE, and MTP inputs to

the touchpanel.

POWER

12V

1.0A MAX

LAN / PoE MTP

kj i

Figure 8. Cable connectors for TLP 710CV

MTP connector (RJ-45)

LAN/PoE

Power connector

MTP input

A twisted pair cable, terminated with an RJ-45 connector, provides composite or S-video and

audio input from an Extron MTP transmitter.

CAUTION: Connect the MTP transmitter to the MTP socket and the network connector

to the network socket. Although both use RJ-45 connectors, the MTP socket

(on the right) must be connected to an MTP transmitter and the LAN/PoE

socket (on the left) must be connected to a LAN. The wires on each connector

use different voltages and inputting the wrong voltages into a socket will

damage the TLP 710CV.

TLP 710CV • Touchpanel Features and Connectors 14

Page is loading ...

Extron electronics TLE 710 User manual

Brand: Extron electronics

Model: TLE 710

Type: User manual

This manual is also suitable for

Download PDF

report

Extron electronics TLE 710 User manual

This manual is also suitable for

Extron electronics TLE 710 User manual

Related papers

Other documents