Universal series RF & WiFi Waterproof Receiver 09.09FWP.040121
Input
Voltage Remarks
Output
Current
12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
Power
12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
12-36VDC Constant current
4x(8.4-25.2)W4x700mA
No.
1
2
3
RF & WiFi Receiver
Waterproof grade: IP67
Radio Frequency : 868/915/434mhz
Function introduction
Product Data
Size(LxWxH)
180.5x73.6x38mm
• DO NOT install with power applied to device.
• This device is IP67 rating and protected against damp environment.
Safety & Warnings
Operation
Learning Key:
Paring with RF remote
Important: Read All Instructions Prior to Installation
Do wiring according to connection diagram.
Pair RF Receiver with RF remote:
1. Connect and wire up the RF receiver correctly, power on.
2. Turn on the remote, click the “Learning Key” button on receiver, immediately click a zone number to pair the
receiver to the specified zone if the remote is a multi-zone controller (if it is a single zone remote, this step is
unnecessary), then touch the color wheel or slider bar on the remote (if the remote does not have color wheel or
slider bar, click or touch any keys), the connected led light on receiver flickers twice, which means well paired.
Note: one receiver can be paired with max 8 remote controls.
Delete the pairing:
1. Wire up the RF receiver correctly, power on.
2. Hold down the “ Learning Key” button on receiver for over 3 seconds until the connected led light on
receiver flickers twice, which means well deleted.
IOS or android system connection to the receiver
Please check ‘Easylighting’ application manual. WiFi password:0123456789
180.5x73.6x38mm
180.5x73.6x38mm
Wiring Diagram
L
N
G
V+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
If Connect with RGBW LED Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
V+ V+
WW WW
CW CW
If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1
Zone 1
Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4
Zone 1 Zone 2 Zone 3
RF remote
RF remote
L
N
G
V+
V-
OUTPUT
INPUT
AC Power
50/60Hz
12V/24V/36V
CV PSU
If Connect with Dual Color LED Strip
Reset Swi tc h Learnin g Ke y
Reset to factory
setting
DC INP UT
LED OU TP UT
DC INP UT
LED OU TP UT
Black :V +
Red :R-
Green :G -
Yell ow : B-
White :W-
Red :V+
Black :V-
Common Anode Output(+)
CH 3:B/WW output(-)
CH 4:W/CW output(-)
CH 1:R/WW output(-)
CH 2:G/CW output(-)
V+
DC Power output
V+
RF & WiFi Receiver
Res et Swit ch Lea rning K ey
DC INPU T
LED OUT PU T
DC INPU T
LED OUT PU T
Black : V+
Red :R-
Green : G-
Yell ow :B -
White : W-
Red :V+
Black : V-
RF & WiFi Receiver
Res et Swit ch Lea rning K ey
DC INPU T
LED OUT PU T
DC INPU T
LED OUT PU T
Black : V+
Red :R-
Green : G-
Yell ow :B -
White : W-
Red :V+
Black : V-
RF & WiFi R eceiv er
Reset S witch Lea rning K ey
DC INP UT
LED OU TPUT
DC INP UT
LED OU TPUT
Blac k :V+
Red :R -
Gree n :G-
Yellow : B-
Whit e :W-
Red :V +
Blac k :V-
RF & WiFi R eceiv er
Reset S witch Lea rning K ey
DC INP UT
LED OU TPUT
DC INP UT
LED OU TPUT
Blac k :V+
Red :R -
Gree n :G-
Yellow : B-
Whit e :W-
Red :V +
Blac k :V-
RF & WiFi R eceiv er
Reset S witch Lea rning K ey
DC INP UT
LED OU TPUT
DC INP UT
LED OU TPUT
Blac k :V+
Red :R -
Gree n :G-
Yellow : B-
Whit e :W-
Red :V +
Blac k :V-
RF & WiFi R eceiv er
Reset S witch Lea rning K ey
DC INP UT
LED OU TPUT
DC INP UT
LED OU TPUT
Blac k :V+
Red :R -
Gree n :G-
Yellow : B-
Whit e :W-
Red :V +
Blac k :V-
RF & WiFi R eceiv er
Reset S witch Lea rning K ey
DC INP UT
LED OU TPUT
DC INP UT
LED OU TPUT
Blac k :V+
Red :R -
Gree n :G-
Yellow : B-
Whit e :W-
Red :V +
Blac k :V-
/
