DOMUS CHAM-REM-3C User manual

Brand: DOMUS

Model: CHAM-REM-3C

Type: User manual

DOMUS CHAM-REM-3C is an RGBW Remote control that allows you to control your lighting with ease. It features 4 zones, enabling you to control multiple receivers simultaneously. With its RF + Bluetooth connectivity, you can pair it with RF + Bluetooth receivers effortlessly. The mesh network capability extends the control distance as receivers can transmit signals to each other. Each remote can control numerous receivers, and each receiver can be paired with up to 8 remote controls.

29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia

Phone: 02 9554 9600 | Fax: 02 9554 9433

[email protected] | www.domuslighting.com.au

Installation Manual

Speciﬁcations

Type of controller: RGBW Remote control Remote size (mm): (L) 136.3mm x (W) 38.9mm x (D) 10.7mm

Protocol: RF + Bluetooth Transmission frequency: 2.4GHz

Dimming range: 0.1% - 100% Transmission range: 30m

Remote colour: Black Operation voltage: 3VDC (CR2025)

Note: -The lamp must be installed by professional electrician

-Ensure the power supply is switched oﬀ before ﬁtting this product

-Do not touch the lamp when in use

-Keep away from hot steam and corrosive gas

CHAM-REM-3C Date: February 1, 2023 2:02 PM

Variants Item No. Details

20142 CHAM-REM-3C RGBW Remote

Thank you for purchasing your new CHAM-REM-3C Remote control, Please take the time to read and understand the instruction

sheet below. Failure to do so may void warranty.

• RF+Bluetooth RGBW remote control

• Enables to control 4 zones of receivers

• Easy & quick pairing to the RF+Bluetooth receivers by simply pushing the buttons

• Mesh network for further control distance, receivers can transmit signal to each other

• Each remote can control numerous receivers

• Each receiver can be paired to max. 8 remote controls

• The controlled receiver status can be quickly synchronised to the smart APP

• Transmission range between every two neighbour devices up to 30m

• Bluetooth low power consumption technology, long battery life

• With magnet on the back, easy fasten to & remove from the bracket

• Waterproof grade: IP20

Safety & Warnings

• This device contains lithium battery that shall

be stored and disposed properly.

• DO NOT expose the device to moisture.

137mm

38.9mm

Brightness up button, press and hold down

to increase light intensity.

RGB color button, press and hold down to

get the color you would like.

On/Oﬀ Button

Click to turn on/oﬀ W channel, press and

hold down to increase/decrease light

intensity of W channel

Scene button, press and hold down to save

a scene, click to recall the saved

Brightness down button, press and hold

down to decrease light intensity.

1 RGB color changing mode, click to play/

pause the mode, press and hold down to

speed up/down the mode.

Zone buttons,

click to choose a zone.

Pair with RF+Bluetooth receiver

Step 1: Do wiring the receiver according to wiring diagram (please refer to the instruction

of RF receiver that you would like to pair with).

Step 2: Click the “Prog. Key” or “Reset” button on RF+Bluetooth receiver (or reset power

of the receiver 3 times continuously if the button is not accessible) to set it into pairing to RF

remote status

Step 4: Then immediately click any other button except zone buttons, LED lights connected

with the receiver ﬂicker once means the receiver is paired with zone successfully.

Step 3: Click a zone button to select a zone (e.g. zone 2).

Note: one receiver can be paired with max 8 remote controls.

If you use multiple receivers, you have two choices:

Option 1: have all the receivers in the same zone, like zone 1

Option 2: have all the receivers in diﬀerent zones, like zone 1, zone 2, zone 3 and zone 4

RF+Bluetooth LED Receiver

Prog

DOMUS CHAM-REM-3C User manual

DOMUS CHAM-REM-3C User manual

DOMUS CHAM-REM-3C User manual

Related papers

Other documents