Pottinger TERRASEM C6 FERTILIZER Operating instructions

Operating manual

Seed drill

TERRASEM C6 fertilizer

8517 : +. . 00176

8517.en.80U.0

PÖTTINGER - Trust creates Affinity since 1871

"Quality pays for itself." Therefore we apply the highest quality standards to our products

which are constantly monitored by our in-house quality management and our management

board. Because the safety, perfect function, highest quality and absolute reliability of our ma-

chines in operation are the core competencies for which we stand.

Technical alterations

There may be deviations between these document and the product as we are constantly de-

veloping our products. Therefore no claims may be derived from the data, illustrations and

descriptions. Please contact your Specialist Service Centre for any binding information about

specific features of your machine.

Legal notes

Please note that only the German operating manual constitutes the original operating manual

in regards to the guidelines 2006/42/EC. Operating manuals on languages different than

German, are translations of the German original manual of operation.

We would ask you to please understand that changes to the scope of supply with regard to

form, equipment and technical specifications are possible at any time.

Any form of reprint, translation or reproduction, including excerpts, requires the written appro-

val of PÖTTINGER Landtechnik GmbH.

All rights according to copyright law are expressly reserved by PÖTTINGER Landtechnik

GmbH.

You can find additional information about your machine in PÖTPRO.

Are you looking for suitable accessories for your machine? No problem! All the information

you require is here at your disposal. And if we don't have what you're looking for, then your

Specialist Service Centre is there for you with help and advice.

Scan the QR code on the type plate of the machine or visit www.poettinger.at/poetpro

2 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Dear Customer

The Operating instructions will allow you to become acquainted with your machine and pro-

vide clear information about safe and correct handling, maintenance and care. Take the time

to read the instructions all the way through.

The operating instructions are a part of the machine. They must be stored in an accessible

location at the workplace for the entire service life of the machine. The user must independ-

ently supplement the instructions regarding national regulations on accident prevention, traf-

fic safety and environment protection.

All persons that are entrusted with the operation, maintenance or transport of the machine

must read and understand these instructions, in particular the safety instructions, before be-

ginning work. Any warranty claims lapse on non-observance of these Instructions.

If you have any questions regarding the contents of these Operating instructions or further

questions regarding the machine, please contact your PÖTTINGER service partner.

Correct maintenance and care according to the defined maintenance intervals will ensure the

operational and traffic safety, as well as the reliability of your machine.

Use only original spare parts or spare parts and accessories that are approved by PÖTTING-

ER Landtechnik GmbH. Only original spare parts that are approved by us have been tested

and accordingly are appropriate for use in your machine. The use of any unapproved parts

forfeits any guarantee or guarantee claim. Even after the end of the warranty period we rec-

ommend using original spare parts to ensure the performance of your machine.

The Product Liability Law obligates manufacturers/dealers to transfer operating instructions

when selling machines, as well as to instruct clients regarding the safety, operation and

maintenance regulations concerning the machine. Confirmation in the form of a declaration

of transfer is required to verify that the implement and Instructions have been transferred cor-

rectly. The declaration of transfer is delivered together with the machine.

Every self-employed person and farmer is an entrepreneur within the meaning of the product

liability legislation. Therefore corporate property damage according to the Product Liability

Law is excluded from the liability of PÖTTINGER. Corporate property damage according to

the Product Liability Law refers to damage caused by the machine. Damage to the machine

is not property damage according to the Product Liability Law.

The operating instructions are a part of the machine, therefore you must transfer them when

selling/transferring the machine to a new user. Train and instruct the new owner in the regu-

lations stated.

The PÖTTINGER service team wishes you the best of luck.

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 3

You will find the following representations in this operating manual

DANGER

If you do not follow the instructions in a text section with this marking, there is a risk

of fatal or life-threatening injury.

► All instructions in such text sections must be followed!

WARNING

If you do not follow the instructions in a text section with this marking, there is a risk

of severe injury.

► All instructions in such text sections must be followed!

CAUTION

If you do not follow the instructions in a text section with this marking, there is a risk

of injury.

► All instructions in such text sections must be followed!

NOTICE

If you do not follow the instructions in a text section with this marking, there is a risk

of damage to property.

► All instructions in such text sections must be followed!

TIP

Text sections marked like this contain special recommendations and tips regarding the ma-

chine operation.

ENVIRONMENT

The text sections marked in this way provide practices and advice on environmental protec-

tion.

Equipment marked as optional is available only for certain machine models or in certain

countries.

Images may differ in detail to your machine and should only be considered as indicative.

4 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Instructions for product handover

Please verify the listed items in order to comply with the liabilities of the product warranty.

Please, tick off where appropriate.

Machine checked according to delivery note. All packing materials removed, all

safety devices, cardan shafts and control elements present.

Machine operation, commissioning and maintenance discussed with and explained

to the clients using the operational instructions.

Tyre air pressure verified.

Tightness of wheel nuts verified.

Reference to correct p.t.o. speed and direction of rotation.

Adaptation to tractor complete; three point adjustment, drawbar height, attachment

of handbrake lever in tractor cab, forced steering set, compatibility of all necessary

electrical, hydraulic and pneumatic connectors to tractor checked and established.

Cardan shaft correctly cut to length.

Test run of all machine functions in addition to parking brake and operating brake

completed and no defects noted.

Function explanation during test run.

Tilting to transport and working position explained.

Information regarding optional equipment provided.

References made to compulsory reading of the operational instructions.

Confirmation is required to prove that the machine and the operating instructions have been

properly handed over. For this purpose you have received a confirmation e-mail from Pötting-

er. If you have not received this mail, please contact your local dealer. Your dealer can fill in

the handover declaration online.

Austria

PÖTTINGER Landtechnik GmbH

Industriegelände 1

4710 Grieskirchen

Phone+43 7248 600-0

Fax+43 7248 600-2513

[email protected]

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 5

Corrosion protection set up in the factory

Remove corrosion protection............................................................................................ 16

Factory standard for bolt torques

Tightening torque.............................................................................................................. 18

Layout and function

Functional elements.......................................................................................................... 19

Electric controls................................................................................................................. 24

Hydraulic controls.............................................................................................................. 25

Sensors and installation positions..................................................................................... 25

Accessories included in the scope of delivery................................................................... 26

Upgrade program.............................................................................................................. 26

At a glance

Identification...................................................................................................................... 27

Type plate with CE marking......................................................................................... 27

Description

EU - declaration of conformity........................................................................................... 29

Intended use..................................................................................................................... 30

Use not in accordance with specifications........................................................................ 30

Technical data

Dimensions....................................................................................................................... 31

Coupling / lower link.......................................................................................................... 31

Tyres................................................................................................................................. 31

Weights............................................................................................................................. 31

Power requirements.......................................................................................................... 32

Machine operation limits................................................................................................... 32

Load limits......................................................................................................................... 32

Seed placement................................................................................................................ 32

Hydraulic system............................................................................................................... 33

Brake system.................................................................................................................... 33

Brakes settings............................................................................................................ 33

Electrics............................................................................................................................. 34

Contents

6 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

POWER CONTROL Terminal........................................................................................... 35

EXPERT 75 Terminal (Option).......................................................................................... 36

CCI terminal (optional)...................................................................................................... 36

Noise emission.................................................................................................................. 37

Safety and the environment

Safety advice..................................................................................................................... 38

Qualification of personnel............................................................................................ 38

Performing maintenance work..................................................................................... 38

Organisational measures............................................................................................. 38

Maintaining operational safety..................................................................................... 38

Special hazards........................................................................................................... 39

Safety devices................................................................................................................... 40

Safety devices............................................................................................................. 40

Warning signs.............................................................................................................. 41

Traffic safety equipment.............................................................................................. 45

Environmental protection.................................................................................................. 47

Handling hazardous substances................................................................................. 47

Fuel efficiency and soil protection............................................................................... 47

Disposal of the machine.............................................................................................. 48

Power-Control Terminal operation

Overview of the POWER CONTROL terminal.................................................................. 49

Input - Keypad............................................................................................................. 49

Basic functions.................................................................................................................. 51

Control system versions.............................................................................................. 51

Turning terminal on/off and “START” menu................................................................ 51

System Menu............................................................................................................... 54

“WORK” menu (operating mode)...................................................................................... 55

Turning the damp drill operation on and off................................................................. 57

Start and stop sowing operation.................................................................................. 58

Adjusting sowing amount............................................................................................. 59

Track marker configuration.......................................................................................... 59

Adjusting the tram line counter.................................................................................... 60

Turning lighting on and off........................................................................................... 60

Emergency shutdown.................................................................................................. 61

Menü "DATA" (Betriebsdaten).......................................................................................... 61

Contents

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 7

Tageszähler anzeigen und einstellen.......................................................................... 63

Jahreszähler anzeigen und einstellen......................................................................... 64

“SET” menu (basic settings).............................................................................................. 66

100-metre calibration................................................................................................... 67

Seed Library settings................................................................................................... 70

Dosing wheel calibration.............................................................................................. 74

Tramline rhythm settings............................................................................................. 81

Adjusting the tramline rhythm............................................................................................ 84

Adjusting seed predosing (seed drilling)...................................................................... 87

Adjusting the waiting time for seed................................................................................... 89

Adjusting monitoring of machine functions.................................................................. 89

Menu "Manual operation" / "Damp drilling".................................................................. 91

“Seed Flow Monitoring” menu..................................................................................... 92

Allocation of seed flow monitoring sensors to tramline..................................................... 96

“CONFIG” menu (machine configuration)......................................................................... 98

Activating the “Machine data" menu............................................................................ 98

“Compatibility” menu.................................................................................................... 99

"TEST" menu.................................................................................................................... 100

Activating the “Dosage Wheel Calibration Area Trial” menu....................................... 101

“Motor test" menu........................................................................................................ 103

“Fill Level and Speed Signal" menu............................................................................. 104

“Error list” menu........................................................................................................... 105

EXPERT 75 ISOBUS-Terminal

EXPERT 75 ISOBUS-Terminal overview.......................................................................... 107

Input - Keypad............................................................................................................. 107

CCI ISOBUS-Terminal

CCI ISOBUS Terminal overview....................................................................................... 109

Input - Keypad............................................................................................................. 109

ISOBUS operation

Input masks....................................................................................................................... 111

Selection masks................................................................................................................ 112

Terminal on /off - "START" menu...................................................................................... 113

Radar sensor (Optional).................................................................................................... 114

Activate “WORK” menu (operating mode)........................................................................ 115

Contents

8 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Damp drill operation settings....................................................................................... 118

Turning manual operation on and off........................................................................... 118

Start and stop sowing operation.................................................................................. 118

Adjusting sowing amount............................................................................................. 119

Operating the tram line counter................................................................................... 119

Turning lighting on and off........................................................................................... 119

Emergency shutdown.................................................................................................. 120

"DATA" menu.................................................................................................................... 120

"DATA" Daily Part-counter menu................................................................................. 120

"DATA" Year Counter menu........................................................................................ 121

Menü "SET" (Grundeinstellungen).................................................................................... 122

"Manual operation" / "Damp drilling" menu.................................................................. 123

"100-metre calibration" menu...................................................................................... 125

Seed Library settings................................................................................................... 126

“Seed File” Menu............................................................................................................... 127

"Seed file" menu settings.................................................................................................. 129

“Dosing Wheel Suggestion” menu.................................................................................... 129

Dosing wheel calibration................................................................................................... 130

Adjusting the tram line rhythm........................................................................................... 137

Key prioritization................................................................................................................ 141

“Seed flow monitoring” menu....................................................................................... 142

Allocation of seed flow monitoring sensors to tramline..................................................... 146

CONFIG menu (machine configuration)............................................................................ 147

Compatibility Mode menu............................................................................................ 147

"Serial Number" menu................................................................................................. 148

“TEST” Menu (Sensor Test).............................................................................................. 149

"Seed flow monitoring indicator" menu........................................................................ 153

"IDS Sensor Test" menu.............................................................................................. 154

Seed Complete (Option)

Seed Complete................................................................................................................. 157

Attaching to tractor............................................................................................................ 158

Seed drill control system................................................................................................... 158

Seed drill general control system................................................................................ 158

Unlocking <TC-GEO> or <TC-SC> in the Pöttinger control system:................................ 159

Seed drill control: variable sowing rate............................................................................. 160

Manually changing the distribution amount dosing 1 / dosing 2 (only with fertilizer ma-

chines):.............................................................................................................................. 160

Contents

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 9

Switching the spread rate transmission on/off.................................................................. 161

CCI command.............................................................................................................. 162

General............................................................................................................................. 162

3. Tab Geometry............................................................................................................... 163

Check the values adopted from the seed drill control:...................................................... 164

Fields:................................................................................................................................ 165

Section Control.................................................................................................................. 166

Operating with CCI.Command.......................................................................................... 168

Seed drill control: with part-width control..................................................................... 171

Preparation for CCI.Control............................................................................................... 177

First steps with the CCI.Control................................................................................... 177

First steps with the CCI.Control........................................................................................ 177

Producing a job file with the application map.................................................................... 178

Generating a job file with two application maps................................................................ 178

Generating an order file without application maps............................................................ 178

Exporting the job file from FMIS to the Isobus terminal.................................................... 178

Import the order data from CCI.Control....................................................................... 179

Adding master data (optional)........................................................................................... 180

Assigning and changing job data (optional)...................................................................... 181

GPS function control......................................................................................................... 181

Starting an order............................................................................................................... 181

Exporting jobs................................................................................................................... 183

Possible error messages................................................................................................... 183

Unlocking apps.................................................................................................................. 183

Switching between apps.............................................................................................. 185

Seed Complete wiring diagram................................................................................... 187

Operation of the functional elements

Machine functions............................................................................................................. 189

Turning ventilators on and off...................................................................................... 189

Activate / deactivate / oversteer functions (ARTIS)..................................................... 189

Flaps, covers, auxiliary and special functions

Opening / closing cover and valves.................................................................................. 192

Seed hopper rolling lid................................................................................................. 192

Seed hopper seed discharge....................................................................................... 193

Seed hopper gate valve............................................................................................... 193

Contents

10 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Metering wheel housing............................................................................................... 195

Fit / remove dosing wheel............................................................................................ 195

Metering system.......................................................................................................... 198

Distributor head with half-machine shut-off................................................................. 198

Distributor head without half-machine shut-off............................................................ 200

Shut off distributor head outlets per tramline motor..................................................... 201

Auxiliary and special functions.......................................................................................... 201

Collection bag.............................................................................................................. 201

Telescopic drawbar..................................................................................................... 202

Extend the telescopic drawbar.......................................................................................... 202

Retract the telescopic drawbar.......................................................................................... 203

Climbing assistance to operating or loading platform.................................................. 204

Loading platform ladder.................................................................................................... 204

Stairway for lateral loading platform.................................................................................. 205

Transport guard

Transport fastenings......................................................................................................... 208

Locking hooks and securing pins................................................................................ 208

Stopcock for hydraulic functions.................................................................................. 210

Operation

Initial operation.................................................................................................................. 213

Brief instructions.......................................................................................................... 213

Adapting the tractor hydraulics.................................................................................... 214

Emergency-brake adjustment bolt position (hydraulic brake)...................................... 214

Adapting the breakaway cable (hydraulic emergency brake valve)............................ 215

Attaching the sowing machine to the tractor................................................................ 217

Calculation of tractor ballast weight............................................................................. 217

Determine the required tractor ballast weights using the weighing method...................... 218

Determine the required tractor ballast weights using calculation...................................... 220

Adjusting and retrofitting................................................................................................... 221

Track looseners (option).............................................................................................. 221

Bout marker disc.......................................................................................................... 222

Hydraulic blower drive................................................................................................. 225

Basic setting...................................................................................................................... 225

Blower drive nominal speed for gross seed (Fan drive without Load-Sensing operation) 226

Blower drive nominal speed for fine seed (Fan drive without Load-Sensing operation)... 227

Contents

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 11

Blower drive basic settings (with Load-Sensing operation(Optional))............................... 229

Air amount distribution with side-dressing................................................................... 231

Blockage of sowing tubes................................................................................................. 233

Adjusting seed dosage................................................................................................ 235

Distribution unit and Tramlines (Machines with no electric butterfly valves)..................... 238

Distribution unit and Tramlines (Machines with electric butterfly valves).......................... 240

Sowing tables for electric dosage..................................................................................... 241

Dosing wheel overview..................................................................................................... 246

Adjusting the share system......................................................................................... 247

Seed placement depth...................................................................................................... 248

Setting the flock thrust roller.............................................................................................. 251

Hydraulic coulter pressure................................................................................................ 253

Contact pressure (ground accommodation) of the folding sections............................ 256

Front board (Option).................................................................................................... 258

Disc-System................................................................................................................ 259

Levelling board............................................................................................................ 263

Settings for the edge plates......................................................................................... 264

Setting the harrow (optional)....................................................................................... 267

Standard curry comb settings...................................................................................... 270

Standard curry comb supplement..................................................................................... 273

Adjusting the tramline marker (optional)...................................................................... 275

Tramlines: for example, for laying..................................................................................... 277

Coupling............................................................................................................................ 279

Air pressure - braking system (Option)........................................................................ 280

Disconnect air brake system connecting lines.................................................................. 282

Connecting hydraulic hoses........................................................................................ 282

Connecting cables....................................................................................................... 283

Mounting the POWER CONTROL terminal................................................................. 284

Fit the ISOBUS terminal.............................................................................................. 285

Fit EXPERT 100 (CCI-100) Terminal ......................................................................... 286

Connect the tractor terminal........................................................................................ 286

Work assignment.............................................................................................................. 287

Transport run............................................................................................................... 287

Transport on loading surfaces........................................................................................... 288

Turn manoeuvres on slopes.............................................................................................. 289

Fill the seed hopper..................................................................................................... 289

Switch machine from road transport position to working position (ARTIS).................. 290

Switch machine from road transport position to working position (ARTIS +).............. 292

Contents

12 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Sowing with POWER CONTROL Terminal / ISOBUS Terminal.................................. 294

Switch machine working position to transport position (ARTIS).................................. 295

Switch machine working position to transport position (ARTIS +)............................... 297

Empty the seed hopper............................................................................................... 298

Putting out of operation..................................................................................................... 300

Emptying the dosage wheel/dosage wheel case......................................................... 300

Empty the seed hopper............................................................................................... 301

Detach the machine from the tractor........................................................................... 303

Unhitching......................................................................................................................... 303

Dismounting the POWER CONTROL terminal............................................................ 304

Remove EXPERT 75 Terminal.................................................................................... 305

Dismounting the CCI terminal...................................................................................... 306

Separate the tractor terminal....................................................................................... 306

Unplug cable................................................................................................................ 306

Disconnecting the hydraulic hoses.............................................................................. 307

Anti-theft device........................................................................................................... 307

Care and maintenance

Ensure operational readiness........................................................................................... 309

General tips....................................................................................................................... 309

Daily maintenance............................................................................................................. 310

Brake fluid fill level....................................................................................................... 310

Check the brake hoses and hose couplings................................................................ 311

Air reservoir................................................................................................................. 312

Cleaning of the filter dust............................................................................................. 313

Check hydraulic system............................................................................................... 314

Check / change lighting of lamps................................................................................. 315

Check / replace warning signs, warning triangles, warning sheets............................. 316

After every season............................................................................................................ 317

Clean the dosage wheel case and the dosage wheel................................................. 317

Clean the demountable dosage wheels...................................................................... 319

Clean inside the seed hopper...................................................................................... 325

Clean outside of machine............................................................................................ 326

Sowing coulter wipers.................................................................................................. 326

Dust protection (option)............................................................................................... 328

As required........................................................................................................................ 330

Clean the dosage wheel case and the dosage wheel................................................. 330

Clean inside the seed hopper...................................................................................... 333

Contents

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 13

Clean terminal............................................................................................................. 334

Clean outside of machine............................................................................................ 334

Front board wearing part............................................................................................. 335

Wear limit harrow tines................................................................................................ 336

Change the track looseners chisel openers................................................................ 338

Thrust roller replacement............................................................................................. 338

After service life................................................................................................................. 340

After first 10 operating hours....................................................................................... 340

Retighten the axle bolts and nuts...................................................................................... 340

Every 20 operating hours............................................................................................ 340

Lubricate feeler wheel swivel bearing............................................................................... 340

Lubricate filling auger swivel mechanism.......................................................................... 341

Every 200 operating hours.......................................................................................... 342

Check the brake lining....................................................................................................... 342

Every 2 years............................................................................................................... 343

Change braking fluid......................................................................................................... 343

Every 6000 hectares.................................................................................................... 343

Check / replace tyre packer wheel bearing....................................................................... 343

Every 4 years............................................................................................................... 344

Check and adjust hydraulic pressure accumulator........................................................... 344

Every 6 years............................................................................................................... 345

Hydraulic hoses................................................................................................................. 345

Lubrication chart................................................................................................................ 345

Operating materials

Specifications for operating materials............................................................................... 347

Working materials and fill amounts................................................................................... 347

Help and advice

What to do if...................................................................................................................... 348

Alarm messages at the Power Control and CCI-ISOBUS Terminal............................ 348

Messages at the CCI terminal / tractor terminal................................................................ 363

Indicated value / indicated symbol incorrect................................................................ 369

Seed delivery error...................................................................................................... 370

Terminal deactivated................................................................................................... 371

Lighting........................................................................................................................ 371

Hydraulic emergency actuation by failure of electricity (Artis plus)............................. 372

Contents

14 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Sensors

Sensor troubleshooting..................................................................................................... 374

Plans

Circuit layouts.................................................................................................................... 375

Electric......................................................................................................................... 375

Cable harness................................................................................................................... 375

Artis plus cable tree hydraulic extension........................................................................... 377

Hydraulic circuit diagrams........................................................................................... 379

Hydraulic plan Terrasem C6 Artis..................................................................................... 379

Hydraulic plan Terrasem C6 Artis plus.............................................................................. 381

Index 383

Contents

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 15

Remove corrosion protection

TIP

Machines that are treated with preserving agents can be recognized by the yellowish wax-

like layer on the surface. For untreated machines, please skip this chapter!

To protect our machines from corrosion damage caused by salt, a preserving agent (Multicor

LH3 Plus, Hersteller Fa. Zeller+Gmelin) should be applied to the entire external surface.

Safety data sheet is available on request from the Pöttinger Client service and the manufac-

turer of the preserving agent.

ENVIRONMENT

Preserving agent and cleaning agent must not be released into the environment and sew-

age systems.

The preserving agent is to be washed off only in a washing facility with a functional oil sep-

arator!

WARNING

Risk of personal injury!

Danger of slipping when accessing the machine.

Health risk through contact with the spray when washing the preserving agent off.

Health risk through contact with the dewaxer provided.

Fire danger through inflammable liquids.

► Do not access machine (and machine parts when machine is partially disassembled).

► When washing the preserving agent off, always wear personal protective equipment

(protective suit, splash goggles, nitrile gloves, rubber boots, breathing mask with parti-

cle filter). Also refer to the preserving agent safety data sheet and the attached safety

data sheet for the dewaxer provided.

► When working with a dewaxer or preserving agent, there must be no fiddling around

with a naked flame, no eating or drinking, no sniffs or smoking.

Corrosion protection set up in the factory

16 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

NOTICE

Danger of property damage

Hot water high pressure cleaning can cause damage to the paintwork, the electrics and hy-

draulics.

Fire danger through inflammable liquids.

► Max. water temperature of 80°C / 176°F

► When using a high pressure cleaner, observe the safety sticker on the machine and do

not point it directly at the distributor, job calculator, chains and bearings. Replace any

safety stickers that may be missing after washing before operating the machine.

► Observe the minimum distance of 30 cm from the high pressure cleaner spearhead to

the painted surfaces, hydraulic hoses, cables and tyres.

► When working with a dewaxer or preserving agent, there must be no fiddling around

with a naked flame or smoking.

Implementation

Before mounting the machine fully remove the preserving agent. Only use the dewaxer provi-

ded to remove the preserving agent. Comply with the delivered safety data sheet of the dew-

axer and the safety instructions of the machine.

Carry out dewaxing as described on the safety plate on the machine.

TIP

Any warranty claims are forfeited:

• if the preserving agent is improperly, incompletely or not at all removed.

• if using a different dewaxer than previously described.

Corrosion protection set up in the factory

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 17

Tightening torque

This factory standard applies to all metric bolts for which no special tightening torque is

specified in the drawing/manual. The relevant grade is visible on the bolt head.

• The values given are nominal and are valid for a head friction rate of IJ=0.14 and a

thread friction of IJ=0.125 Slight tensioning force differences can exist through differing

friction rates. The values given are to be kept to a tolerance of ± 10%.

• By using the given tightening torque and the existing friction rate used, then up to 90%

of the minimum yield strength of the bolt material is used in accordance with DIN ISO

898 .

• If a specific tightening torque is given for a bolt connection, then all these bolt connec-

tions are to be tightened to the specified tightening torque using a torque wrench.

Thread Grade 8.8 Grade 10.9

Tightening tor-

que in Nm

Tensioning force

in N

Tightening tor-

que in Nm

Tensioning force

in N

M 4 3.1 4000 4.4 5700

M 5 6.2 6600 8.7 9300

M 6 10.5 9300 15 13000

M 8 25 17000 36 24000

M 10 50 27000 70 38000

M 12 86 39500 121 56000

M 14 135 54000 195 76000

M 16 215 75000 300 105000

M 20 410 117000 580 164000

M24 710 168000 1000 237000

M 30 1400 270000 2000 380000

M 8 x 1 27 18700 38 26500

M 10 x 1.25 53 29000 74 41000

M 12 x 1.25 95 44500 130 63000

M 14 x 1.5 150 60000 210 85000

M 16 x 1.5 230 81000 320 115000

M 20 x 1.5 460 134000 650 189000

M 24 x 2 780 188000 1090 265000

Factory standard for bolt torques

18 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Functional elements

Names and functions

Pos. Element Function

1 The drawbar with drawbar

eye / telescopic drawbar

with attached rocker

allows for narrower curves on a headland. During

transportation; telescoping (Optional).

2 Support stand Ensures stability when the machine is parked.

3 Loading platform with a

ladder

Cabin platform with foldable ladder for filling the seed

hopper as well as for maintenance work.

4 Seed hopper Seed hopper

5 Side loading platform Cabin platform with ladder and staircase for mainte-

nance work.

The side platform is only to be used when machine is

in the operating position.

6 Dosing wheel housing with

dosing wheel

The dosing wheel regulates the sowing rate for the

seed drill; Electric drive.

7 Seed distributor For even seed distribution into the sowing hoses that

lead to the coulter system. Mechanically or electrically

controlled valves at the outputs allow the sowing hose

to be blocked when required.

8 Track marker (Optional) The track marker indicates the track to be driven. Hy-

draulic drive, automatic control.

9 Warning sign with rear

lights, rear right

Rear lamps and warning signs (depending on country

of destination)

10 Tramline marker (Optional) Tramline markers denote the tramlines that are kept

free of seed for machines that follow. Hydraulic drive,

automatic or semi-automatic control.

11 Harrow tines The harrow closes the sowing lines and evenly covers

the seed with soil.

12 Coulter thrust rollers Coulter thrust rollers ensure safe soil closure by re-

compacting the furrow.

13 DUAL DISC double-disc

coulters

The coulter system deposits the seed in the sowing

furrow.

14 Tyre packer The tyre packer ensures controlled and uniform recom-

pacting ahead of the coulters and serves as a chassis

for street transportation.

15 Left edge plate For a uniformly even working pattern, the edge plates

are standard and multi-adjustable on both sides .

16 Disc system (Disc harrow) The maintenance-free, rubber-mounted discs loosen

the soil all over the surface.

17 Rolling cover Rolling cover made from tarpaulin fabric; dust and rain-

proof.

18 Warning sign with side

lights, front left

Front position lamps and warning signs, depending on

country of destination.

Layout and function

8517.en.80U.0 Operating manual TERRASEM C6 fertilizer | 19

Pos. Element Function

19 Radar sensor Measuring the speed

20 Fan The hydraulically powered fans provide the air flow re-

quired for the pneumatic delivery of the seed.

21 Right edge plate For a uniformly even working pattern, the edge plates

are standard and multi-adjustable on both sides .

Layout and function

20 | Operating manual TERRASEM C6 fertilizer 8517.en.80U.0

Page is loading ...

Pottinger TERRASEM C6 FERTILIZER Operating instructions

Pottinger TERRASEM C6 FERTILIZER Operating instructions

Related papers

Other documents