KC HiLiTES 6315 User manual

Type
User manual

KC HiLiTES 6315 is a relay wire harness for two lights with a maximum power of 130 watts each. It includes a switch, relay, sheet metal screw, and six wire ties. This harness allows you to easily install and wire KC HiLiTES lights to your vehicle's electrical system, providing control over the lights with the included switch. Ensure safe and reliable operation by connecting the power leads to the battery and grounding the system appropriately.

KC HiLiTES 6315 is a relay wire harness for two lights with a maximum power of 130 watts each. It includes a switch, relay, sheet metal screw, and six wire ties. This harness allows you to easily install and wire KC HiLiTES lights to your vehicle's electrical system, providing control over the lights with the included switch. Ensure safe and reliable operation by connecting the power leads to the battery and grounding the system appropriately.

Mounng Your Lights: 1.
Aer choosing a locaon to mount your lights, install and loosely ghten before installing the wiring
harness.
Wiring Your Lights: 2.
2. To install the switch, drill a ¾” hole in the desired locaon to press the switch into.
(Note: Do not install switch unl you have the switch wires routed to the switch locaon,
and then aach the switch wires accordingly before pressing the switch into the mounng hole). Connect
the switch wires as follows: Black wire to Ground (brass color) blade, Green wire to Load (center) blade,
and White wire (Supply) to the last blade on the switch. Complete the switch installaon and place
switch in the O posion.
1. Begin by roung the KC wire harness from the baery (or power source) and connect the light leads
(DT connectors) to the lights. Next, route the three switch leads (spade connectors) toward the desired
switch locaon.
3. Next, mount the Relay close to the baery with blades facing down (sheet metal screw provided).
Connect the Yellow Power lead (with ring terminal) to the (+) Posive side of the baery. Connect
the Black Ground lead (with ring terminal) to the (-) Negave side of the baery or chassis ground.
Complete the wiring system by connecng the White switch power wire to (+) Posive baery, fuse
box or other power source. The system will not work without powering the white wire.
Aiming Your Lights:
Fog Lights - aim lights so that the top beam cuto is below the level of your stock low beams.
For two lights (130w maximum each)
Spot Lights - aim just above your high beams for maximum distance.
Driving Lights - aim so that the intense part of the beam is near the level of your stock high beams.
(Note: Securely ghten the lights aer aiming them.)
3.
Parts Included:
#6315 - RELAY WIRE HARNESS
KC HiLiTES, Inc. Williams, Arizona USA www.kchilites.com Copyright 2017 Rev 20171004- KC3264QB
Thank you for purchasing KC HiLiTES products; your sasfacon is very important to us. If you have any quesons
regarding this product or any other KC HiLiTES products, please contact us at (888) 689-5955 or visit kchilites.com.
(1) Wire Harness, (1) Switch, (1) Relay, (1) Sheet Metal Screw, (6) Wire Ties
Black
Fuse
3A
Ground
Load Green
White
Yellow
Fuse
20/25A
Ground
Supply
+12 VDC Battery
or other
Power Source
+12 VDC
Battery
Brass Color Blade
  • Page 1 1

KC HiLiTES 6315 User manual

Type
User manual

KC HiLiTES 6315 is a relay wire harness for two lights with a maximum power of 130 watts each. It includes a switch, relay, sheet metal screw, and six wire ties. This harness allows you to easily install and wire KC HiLiTES lights to your vehicle's electrical system, providing control over the lights with the included switch. Ensure safe and reliable operation by connecting the power leads to the battery and grounding the system appropriately.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI