Instructions
Manitowoc Beverage Systems Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
020003338
11/10
Subject: FRP ADA Splash Panel Retrofit Installation
The ADA touch pads are configured to mimic
the function of the main touch pads on the left
and right sides of the splash panel for
handicapped accessibility to drink flavors.
TOOLS NEEDED
• #2 Phillips Screwdriver
• Power Drill
• #29 (.136") Bit, for 6-32 Self-tapping Screw
• Tape Measure
• Marker or Scribe
KIT CONTENTS
• Splash Panel with ADA Touchpad's
• Four Ribbon Cables
•Zip Ties
• ADA Flavor ID Label Sheet
• Instruction Sheet
• Template to Relocate Holes
INSTRUCTIONS
1. Disconnect dispenser from electrical power source.
2. Remove Merchandiser and Splash Panel.
3. Relocate both left and right Splash Panel screw mount points as shown below.
4. Replace all 4 primary valve touch pad ribbon cables, (1,3,4,6) with the new cables supplied. Note that the new cables are numbered the same
as the existing cables, (EXAMPLE: New cable marked #1 will replace existing cable #1), see the ADA Ribbon Cable Wiring Diagram
illustration in the upper right of this page.
Locate
Current Right
or Left Side
Splash Panel
Bracket &
Remove
Using #2
Phillips
Screwdriver.
a
b c
d
Attach
Template
Using the
Top Hole
From the
Bracket
Removed.
Use the
Template to
Locate ,
Mark, & Drill
2 New Holes
Using a #29
(.136") Bit
Remove
Template &
Re-attach
bracket.
Repeat
process for
opposite
side of the
machine.
ADA Touch Pads
ADA Ribbon Cable Wiring Diagram
FRP ADA Splash Panel Retrofit Installation 020003338 11/10
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
NOTE: Use the zip ties provided to secure the ribbon cables. The center plug with 2 ribbon cables is plugged into the control board. The shorter of
the two cables is plugged into the touch pad control above the valve. The longer ribbon cable is to be fed down behind the syrup beverage tubing,
exiting out the lower front of the unit, to be connected to the ADA Touch pad in the Splash Panel, see above.
5. After connecting all four ribbon cables to their respective touch pads, place the splash panel back into position and test each pad
for function, see below. Each ADA touch pads should activate the nozzle indicated below. If the wrong nozzle is activated check
for a cross connection of the ribbon cable. Note that the blue LED light will illuminate, (not blink) at the touch pad control above
the valve during activation.
6. Once correct operation has been confirmed, place flavor I.D. labels on ADA touch pad as shown in Photo 6 by aligning the outer edges
of the label with the control pad frame, and press into place. Replace the unit Merchandiser, and then the ADA Splash Panel. As you
replace the splash panel do not pinch the ribbon cables.
Connect New Ribbon Cables to Board Connect Ribbon Cables to Splash Panel
Route Ribbon Cables
S1
S3
CORRESPONDING PAD
ADA 1
ADA 2
CORRESPONDING PAD
CORRESPONDING PAD
CORRESPONDING PAD
S2
S4
S5
S7
S6
S8
F1
F2
F4
F3
N1
N3
N2
S12
S10
S11
S9
S16 S14
S15
S13
F5
F6
F8
F7
N4
N6
N5
S1
S3
S2
S4
S5
S7
S6
S8
S12
S10
S11
S9
S16 S14
S15 S13
ADA 3
ADA 4
Connect New Ribbon Cables to Board Connect Ribbon Cables to Splash Panel
-
1
-
2
MULTIPLEX FRP ADA Splash Panel Retrofit Kit (020003338) Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
MULTIPLEX Flav'R-Pic Owner Instruction Manual
-
-
KitchenCare ADA Retrofit for Discrete Valves 020004003 Installation guide
-
KitchenCare ADA Retrofit for Variety Valves 020004037 Installation guide
-
KitchenCare FRP-FlavorShot-Selectable Ice ADA Retrofit 020004046 Installation guide
-
KitchenCare SV & Selectable Ice ADA Retrofit 020004047 Installation guide
-
-
-
-
