DESTACO REP3 Series User manual

Brand
DESTACO
Model
REP3 Series
Type
User manual
destaco.com
Automating Tomorrow™
WARNING: This is a controlled document. It is your responsibility to deliver this information to the end user of the
Destaco Robohand product. Failure to deliver this could result in your liability for injury to the user or damage to the
machine. For copies of this manual, call your Customer Service Representative at 1.248.836.6700
ROBOHAND
Service Manual
REP-3 Series
Dimensions and technical information are subject to change without notice
Parallel Grippers | Maintenance and Assembly Procedure
164
REP-3 Series
Third Angle
Projection
Seal Kit
Items
Thread
Locker
Krytox™
Lubricant
Teflon®Based
Grease
Lightweight
Machine Oil
Super
Bonder
8
9
5
7
6
3
2
65
4
1
x3
x3
x3
x1
x4
x2
Item Qty Name
01 1 Body
02 1 Piston
03 1 Cam Driver
04 1 Cap
05 3 Cam Lever
06 3 Jaw
07 3 Cover
08 1 Shielded Case
09 3 Pivot Pin
65 1 Springs Kit
NOTE: Contact the Robohand Sales
Department for a complete spare parts list
with order numbers and prices.
Assembly Procedure
1) Lubricate and install the seals onto the
cap (x3), the piston (x2) and the body (x1).
2) If top airports are used, put the plug
screws out of the cap (#4) and plug the
side airports in the body (#1).
3) Assemble the piston (#2) and the cam
driver (#3) with the washer and the
screw.
- RE option: Place the counterbore holes
of the piston on the cam
driver side
- RI option: Place the counterbore holes of
the piston on the screw side
4) Insert the piston into the body. Orientate
the piston so that the magnets are
placed in front of the body slots.
- RE option: insert the springs (#65)
between the body and the
piston in the counterbore holes
5) Place and screw the cap onto the body.
The dowel holes of the cap and of the
body have to be aligned.
- RI option: insert the springs (#65)
between the cap and the
piston in the counterbore holes
6) Lubricate the slots and the jaws (#6), the
groove of the cam driver and the
levers (#5).
7) Insert together the lever and the jaws
into the body.
8) Insert the pivot pin aligning cam driver
hole. The flat of the pivot pin has put in
front of the rear side of the body. Screw
SS screw into the body for preventing
pivot pin from moving.
9) Assemble the cover (#7) into the body
and fix them with SS screws.
10) Assemble the shielded case.
SK Seal Repair Kit Order #’s
See Product Data Sheets
For more information call us at: 1-800-ROBOHAND or 203-261-5558 Fax: 203-452-7418 Visit us on the Internet at: www.robohand.com
REP Series Exploded View
1-194
REP THREE
JAW SERIES
1.176-1.210 (RPC-REP-RIP-PPC) 9/19/04 11:43 AM Page 194
Dimensions and technical information are subject to change without notice
Parallel Grippers | Maintenance and Assembly Procedure
165
REP-3 Series
For more information call us at: 1-800-ROBOHAND or 203-261-5558 Fax: 203-452-7418 Visit us on the Internet at: www.robohand.com
1.195
REP THREE
JAW SERIES
REP Series Assembled View
Third Angle
Projection
Seal Kit
Items
Thread
Locker
Krytox™
Lubricant
Teflon®Based
Grease
Lightweight
Machine Oil
Super
Bonder
Item Qty Name
01 1 Body
02 1 Piston
03 1 Cam Driver
04 1 Cap
05 3 Cam Lever
06 3 Jaw
07 3 Cover
08 1 Shielded Case
09 3 Pivot Pin
65 1 Springs Kit
NOTE: Contact the Robohand Sales
Department for a complete spare parts list
with order numbers and prices.
2
4
6
8
9
65
1
3
7
5
Accessory Installation & Adjustment Instructions
Installation - Inductive Sensors Holder Kit
1) Assemble the sensors holder (#1) onto the
gripper with its screw (#4)
2) Place the flag (#2) on one of the jaws
above the sensors holder.
3) Place the two spacers (#3) on the
other jaws.
4) Insert each sensor (#5) into the slot on
the holder and screw its two locking nuts,
without blocking them.
5) Position each sensor for desired stroke
position and so that it detects the flag.
6) Tighten sensor locking nuts.
Installation - Stripper Plate
1) Unscrew the screws (#9) to disassemble
the shielded case.
2) Insert the springs (#10) into the stud (#7).
3) Lubricate the body holes previously to insert
the springs and the stud.
4) Re-assemble the shielded case on the body.
5) Install the pressure plate (#8) onto the stud.
1
2
3
5
6
4
7
8
9
10
1.176-1.210 (RPC-REP-RIP-PPC) 9/19/04 11:43 AM Page 195
Global Locations
NORTH AMERICA
Corporate Headquarters
Auburn Hills, Michigan
Toll Free: 1.888.DESTACO
Marketing: [email protected]
Global Technology Center
Auburn Hills, Michigan
Tel: 1.248.836.6700
Customer Service: [email protected]
Mt. Juliet, Tennessee
Tel: 1.888.DESTACO
Customer Service: [email protected]
Wheeling, Illinois
Tel: 1.800.645.5207
Customer Service: [email protected]
Red Wing, Minnesota (Central Research Laboratories)
Tel: 651.385.2142
Customer Service: [email protected]
ASIA
Bangkok, Thailand
Tel: +66-2-326-0812
Customer Service: [email protected]
Shanghai, China
Tel: +86-21-6081-2888
Customer Service: [email protected]
Bangalore, India
Tel: +91-80-41123421-426
Customer Service: [email protected]
EUROPE
Oberursel, Germany
Tel: +49-6171-705-0
Customer Service: [email protected]
Sainte Florine, France
Tel: +33-4-73545001
Customer Service: [email protected]
Wolverhampton, United Kingdom
Tel: +44-1902-797980
Customer Service: [email protected]
Sant Boi de LLobregat, Spain
Tel: +34-936361680
Customer Service: [email protected]
Uithoorn, Netherlands
Tel: +31-297285332
Customer Service: [email protected]
Spain
Netherlands
UK
France
India
Thailand
China
Mt. Juliet, TN USA
Auburn Hills, MI USA
Germany
Red Wing, MN USA
Wheeling, IL USA
© Copyright, 2019 DESTACO. All rights for layout, photos and text rest with the publisher
DESTACO. All photomechanical or other reproductions only with our express permission.
All sales are based on our terms and conditions of sale, delivery and payment. IN_SM-REP-3_03/19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

DESTACO REP3 Series User manual

Brand
DESTACO
Model
REP3 Series
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents