Lithonia Lighting RTLR LED Installation guide

Brand: Lithonia Lighting

Model: RTLR LED

Type: Installation guide

Acuity Brands Lighting, Inc.

One Lithonia Way

Conyers, GA 30012

770-922-9000

U2129801

REV. A

4/17/2008

Installation Instructions

ES8R Retroﬁ t Kit

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER

AFTER INSTALLATION.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT

IN DEATH, SERIOUS INJURY OR SIGNIFICANT PROPERTY DAMAGE. For your protection,

read and follow these warnings and instructions carefully before installing or maintaining this equipment. These

instructions do not attempt to cover all installation and maintenance situations. If you do not understand these

instructions or additional information is required, contact Acuity Brands Lighting or your local Acuity Brands

Lighting distributor.

WARNING: RISK OF ELECTRIC SHOCK. Never connect to, disconnect from or service while circuit

equipment is energized.

WARNING: RISK OF FIRE. Lamps are hot. Keep combustible materials away from hot parts. Observe

lamp manufacturer’s warnings, recommendations and restrictions on lamp operation and maintenance. Make

sure lamps are correctly installed. Use supply conductors with a minimum insulation temperature rating as

speciﬁ ed on equipment.

WARNING: Do not use abrasive materials, glass cleaners or other solvents on reﬂ ector or lens. Use of these

substances may damage ﬁ xture, which may result in personal injury.

WARNING: RISK OF PERSONAL INJURY. This equipment may have sharp edges. Wear gloves to

prevent cuts or abrasions when removing from carton, handling and maintaining this equipment.

Do not install a damaged ﬁ xture.

•

This equipment must be installed in accordance with all applicable installation codes and ordinances.•

Proper grounding is required to ensure personal safety.•

All service shall be performed by qualiﬁ ed service personnel. This equipment must be installed and •

maintained in accordance with all applicable installation codes by a person familiar with the construction

and operation of this product and any hazards involved.

CAUTION: Observe lamp manufacturer’s recommendations and restrictions on lamp operation, including but

not limited to ballast type, burning position, replacement and cycling. We recommend only lamps that comply

with applicable ANSI standards.

All ﬂ uorescent lamps contain mercury. Follow disposal laws. See www.lamprecycle.org or contact your state

environmental protection department for more information.

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or

careless installation or handling of this product.

SAVE THESE INSTRUCTIONS

DISCONTINUED

Class R Type II Reﬂ ector Retroﬁ t Kit

Installation Instructions for Fixture Conversion Retroﬁ t Classiﬁ ed by Underwriters Laboratories, Inc.

Reﬂ ector Kit Type II: Reﬂ ector installation or replacement

Lamp holder relocation, removal or replacement

Ballast relocation, removal, replacement or addition

Installation Instructions

The installation of the Class R reﬂ ector kit Type II shall be performed by qualiﬁ ed personnel by completing the steps listed

below.

This retroﬁ t kit will consist of:

(1) end bracket/ballast assembly prewired with ballast and sockets mounted (ballast will be Class P with UL approvals

and wiring diagram on label)

(1) splice box

(2) reﬂ ectors

(1) louver assembly and mounting hardware consisting of:

(2) quarter-turn fasteners

(60) #8 self-drilling TEK screws

Job packs will have screws bulk-packed with each pallet of kits.

Verify the contents of the retroﬁ t kit by using the diagram below.

End Brackets/Splice Box Reﬂ ectors Louver

DISCONTINUED

Step One:

Remove existing components from host ﬁ xture.

Locate the ﬂ uorescent lighting ﬁ xture that is to be retroﬁ tted. Turn off power.

WARNING: Electrical shock can occur during retroﬁ t component installation if power is not turned off.

WARNING: Installation of this retroﬁ t assembly requires a person familiar with the construction and operation of

ﬂ uorescent luminaire electrical system and the hazard involved.

WARNING: Unless otherwise indicated, do not make or alter any opening in the compartment of wiring or electrical

components during installation of this retroﬁ t assembly.

WARNING: Ensure that existing ﬁ xture is and remains properly connected to building ground.

Use of any other than Lithonia Lighting supplied screws to install assembly may result in ungrounded ﬁ xture

components.

Remove existing louver, lamps and channel cover. Identify power supply wires to disconnect. Follow installation step

2 wiring option A or B based on incoming supply wire. Remove ballast, sockets and lampholder bracket. Recycle or

properly dispose of all components removed from host ﬁ xture.

Step Two:

Install relight assembly.

Install end brackets to 2’ length (socket side) of ﬁ xture. Install end bracket assembly by inserting bottom ﬂ ange between

bottom of ﬁ xture end plate and tee-bar. Center end bracket and attach using two 8-32 self-drilling TEK screws (provided).

Repeat on opposite end of ﬁ xture as shown.

End brackets are retained with two TEK screws (provided) in the small holes at the top of the bracket.

DISCONTINUED

Install reﬂ ectors by inserting notched

end of the reﬂ ector past lance in end

bracket assembly and then rotating

opposite end (end containing quarter-

turn fastener) into ﬁ xture.

Shift reﬂ ector until notches are locked

in place under lance and attach using

a quarter-turn fastener. Rotate second

reﬂ ector 180° and repeat installation

steps.Install lamps. Use center slot in

housing to clear lamp pins.

Install louver assembly by inserting

hinge into slot of end bracket and

sliding back into the corner. Repeat

with opposite hinge, swing louver

closed and rotate latches into locked

position.

Help save our environment by recycling all remaining components.

Save these instructions.

Option A: Fixture Supply wire

is (2) #18AWG solid

1) Remove splice to existing

ballast.

2) Connect #18AWG black

and white to ES8R ballast

disconnect.

Option B: Fixture supply wire

is any other than (2) #18 AWG

solid

1) Cut ballast input leads 6 "

from splice, and strip lead to

3/8”.

2) Connect #18 AWG black

and white (old ballast

input lead) to RT5R ballast

disconnect.

3) Install splice box to cover

input wire splice, using two

TEK screws.

Make wire connections and ground assembly to host ﬁ xture per option A or B based on existing ﬁ xture supply wire.

TEK SCREWS

BRACKET

END

FLANGE SITS ON T-BAR

BENEATH FIXTURE

BDP

TEK SCREW

END

BRACKET

TEK SCREW

TEK SCREWS

BDP

END

BRACKET

TEK SCREW

TEK SCREWS

BDP

END

BRACKET

DISCONTINUED

Lithonia Lighting RTLR LED Installation guide

Lithonia Lighting RTLR LED Installation guide

Lithonia Lighting RTLR LED Installation guide

Related papers

Other documents