Lithonia Lighting RTLR LED Installation guide

Brand: Lithonia Lighting

Model: RTLR LED

Type: Installation guide

Installation Instructions

2RTLEDR/2RTLEDRT Relight Assembly

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER

AFTER INSTALLATION.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT

IN DEATH, SERIOUS INJURY OR SIGNIFICANT PROPERTY DAMAGE. For your protection,

read and follow these warnings and instructions carefully before installing or maintaining this equipment. These

instructions do not attempt to cover all installation and maintenance situations. If you do not understand these

instructions or additional information is required, contact Acuity Brands Lighting or your local Acuity Brands

Lighting distributor.

WARNING: RISK OF ELECTRIC SHOCK. Never connect to, disconnect from or service while circuit

equipment is energized.

WARNING: RISK OF FIRE. Lamps are hot. Keep combustible materials away from hot parts. Observe

lamp manufacturer’s warnings, recommendations and restrictions on lamp operation and maintenance. Make

sure lamps are correctly installed. Use supply conductors with a minimum insulation temperature rating as

speciﬁ ed on equipment.

WARNING: Do not use abrasive materials, glass cleaners or other solvents on reﬂ ector or lens. Use of these

substances may damage ﬁ xture, which may result in personal injury.

WARNING: RISK OF PERSONAL INJURY. This equipment may have sharp edges. Wear gloves to

prevent cuts or abrasions when removing from carton, handling and maintaining this equipment.

• Do not install a damaged ﬁ xture.

• This equipment must be installed in accordance with all applicable installation codes and ordinances.

• Proper grounding is required to ensure personal safety.

• All service shall be performed by qualiﬁ ed service personnel. This equipment must be installed and

maintained in accordance with all applicable installation codes by a person familiar with the construction

and operation of this product and any hazards involved.

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or

handling of this product.

SAVE THESE INSTRUCTIONS

Acuity Brands Lighting, Inc.

One Lithonia Way

Conyers, GA 30012

770-922-9000

U219766

REV. A

6/1/2011

U219766

REV. B

ECO 074-13993

10/22/2013

DISCONTINUED

Class R Type II Reﬂ ector Retroﬁ t Kit

Installation Instructions for Fixture Conversion Retroﬁ t Classiﬁ ed by Underwriters Laboratories, Inc.

Reﬂ ector Kit Type II: Reﬂ ector installation or replacement

Lamp holder relocation, removal or replacement

Ballast relocation, removal, replacement or addition

Installation Instructions

This retroﬁ t kit will consist of:

(2) end brackets

(1) light engine with prewired driver and LED boards

(1) splice box

(1) trim assembly and mounting hardware consisting of:

(7) #8 self-drilling TEK screws

(2) quarter-turn fasteners

Job packs will have screws bulk-packed with each pallet of kits.

*2RTLEDRT Kits for Lensed Troffers will have (2) white molded trim strips

Verify the contents of the retroﬁ t kit by using the diagram below.

End Brackets

Light Engine Splice Box

Trim

U219766

REV. B

ECO 074-13993

10/22/2013

DISCONTINUED

Step One:

Remove existing components from host ﬁ xture, including lampholders and lampholder leads.

Locate the ﬂ uorescent lighting ﬁ xture that is to be retroﬁ tted. Turn off power.

WARNING: Electrical shock can occur during retroﬁ t component installation if power is not turned off.

WARNING: Installation of this retroﬁ t assembly requires a person familiar with the construction and operation of

ﬂ uorescent luminaire electrical system and the hazard involved.

WARNING: Unless otherwise indicated, do not make or alter any opening in the compartment of wiring or electrical

components during installation of this retroﬁ t assembly.

WARNING: Ensure that existing ﬁ xture is and remains properly connected to building ground.

Use of any other than Lithonia Lighting supplied screws to install assembly may result in ungrounded ﬁ xture

components.

Remove existing louver, lamps and channel cover. Identify power supply wires to disconnect. Follow installation step

2 wiring option A or B based on incoming supply wire. Remove ballast, lampholder, lampholder leads, and lampholder

bracket. Recycle or properly dispose of all components removed from host ﬁ xture.

This kit is approved for installation in existing luminaires of steel construction, (not aluminum), in dry or damp locations.

This kit is approved for use in air handling luminaires when the intended air path is along the luminaire side(s) as shown

below in Figure A.

Air Path

Figure A:

U219766

REV. B

ECO 074-13993

10/22/2013

DISCONTINUED

Step Three:

Hang pre-assembled and pre-wired LED light engine assembly by sliding open slots over the tabs on the end brackets.

Make wiring connections and ground (bond) assembly to host ﬁ xture per Option A or B shown in diagram on next page

based on existing supply wire. Reﬂ ector assembly ground wire must be attached to host ﬁ xture to ensure bonding.

Step Two:

Install end bracket assembly by inserting bottom ﬂ ange between the bottom of host ﬁ xture end plate and the T-grid.

Center end bracket and attach using two 8-32 self-drilling TEK screws (included) through the holes at the top of the

bracket. Repeat on opposite end of ﬁ xture as shown.

U219766

REV. B

ECO 074-13993

10/22/2013

DISCONTINUED

Option A:

Fixture Supply wire is (2) #18AWG solid

1) Remove splice to existing

ballast.

2) Connect #18AWG black

and white to 2RTLEDR

ballast disconnect.

3) Connect reﬂ ector assembly

ground wire to host ﬁ xture to ensure

bonding.

Option B:

Fixture supply wire is any other than (2)

#18 AWG solid

1) Cut ballast input leads 6 " from

splice, and strip lead to 3/8”.

2) Connect #18 AWG black and

white (old ballast input lead) to

2RRTLEDR ballast disconnect.

3) Install splice box to cover input

wire splice, using two TEK screws.

4) Connect reﬂ ector assembly

ground wire to host ﬁ xture to ensure

bonding.

TEK SCREWS

BRACKET

END

FLANGE SITS ON T-BAR

BENEATH FIXTURE

BDP

TEK SCREW

END

BRACKET

TEK SCREW

TEK SCREWS

BDP

END

BRACKET

TEK SCREW

TEK SCREWS

BDP

END

BRACKET

Optional Step:

U219766

REV. B

ECO 074-13993

10/22/2013

DISCONTINUED

Help save our environment by recycling all remaining components.

Save these instructions.

Step Four:

Raise light engine into horizontal position and secure to opposite end bracket with included quarter turn fasteners.

Step Five:

The trim assembly hinges and latches from either side. Simply slide corner hinge into the slot on one of the end brackets

and repeat on opposite side. Close door and secure by engaging cam latches.

U219766

REV. B

ECO 074-13993

10/22/2013

DISCONTINUED

Important Note:

The acrylic lens has an

optical film insert.

DO NOT REMOVE THIS

OPTICAL FILM.

Lithonia Lighting RTLR LED Installation guide

Lithonia Lighting RTLR LED Installation guide

Lithonia Lighting RTLR LED Installation guide

Related papers

Other documents