WAGO 2DO 230 V AC 1.0 A, Relay 2CO, potential-free /XTR User manual

Type
User manual
Pos: 2 /D ok ument ati on al lg em ein/E inb and /Ei nban d F ro ntsei te - Han dbuc h; C I 20 17; mit Do cVar ia ble n (St an dard) @ 28\mod_1486477502910_0.docx @ 405388 @ @ 1
Manual
WAGO-I/O-SYSTEM 750 XTR
750-517/040-000
2DO 230V AC 1.0A/ Relay 2CO /XTR
2-Channel Relay Output Module 230 VAC, 1.0 A,
2 Changeover Contacts /XTR
Version 1.3.0
Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Rec htlic h es, A llg emei nes /Im pre ssu m f ür St and ard han dbüc her - al lg. Ang aben, A nschr iften, Telefo nnum mern un d E-Mail- Adres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1
2 WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
© 2019 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 1 69
Web: www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 4 45 55
Fax: +49 (0) 571/8 87 84 45 55
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==
WAGO-I/O-SYSTEM 750 XTR Table of Contents 3
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1
Table of Contents
1 Notes about this Documentation ............................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright ................................................................................................ 5
1.3 Symbols ................................................................................................. 6
1.4 Number Notation .................................................................................... 8
1.5 Font Conventions ................................................................................... 8
2 Important Notes ........................................................................................ 9
2.1 Legal Bases ............................................................................................ 9
2.1.1 Subject to Changes ............................................................................ 9
2.1.2 Personnel Qualifications .................................................................... 9
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ....... 9
2.1.4 Technical Condition of Specified Devices......................................... 10
2.1.4.1 Disposal ...................................................................................... 10
2.1.4.1.1 Electrical and Electronic Equipment ........................................ 10
2.1.4.1.2 Packaging ............................................................................... 11
2.2 Safety Advice (Precautions) ................................................................. 12
3 Device Description .................................................................................. 15
3.1 View ..................................................................................................... 17
3.2 Connectors ........................................................................................... 18
3.2.1 Data Contacts/Local Bus .................................................................. 18
3.2.2 Power Jumper Contacts/Field Supply .............................................. 19
3.2.3 CAGE CLAMP
®
Connectors ............................................................. 19
3.3 Display Elements .................................................................................. 20
3.4 Operating Elements .............................................................................. 20
3.5 Schematic Diagram .............................................................................. 21
3.6 Technical Data ..................................................................................... 22
3.6.1 Device Data ..................................................................................... 22
3.6.2 Supply .............................................................................................. 22
3.6.3 Communication ................................................................................ 22
3.6.4 Outputs ............................................................................................ 23
3.6.5 Connection Type .............................................................................. 23
3.6.6 Mechanical Conditions ..................................................................... 23
3.6.7 Climatic Environmental Conditions ................................................... 24
3.7 Load Limiting Curve .............................................................................. 24
3.8 Approvals ............................................................................................. 25
3.9 Standards and Guidelines .................................................................... 27
4 Process Image ......................................................................................... 33
5 Mounting .................................................................................................. 34
5.1 Mounting Sequence .............................................................................. 34
5.2 Inserting and Removing Devices .......................................................... 35
5.2.1 Inserting the I/O Module ................................................................... 35
5.2.2 Removing the I/O Module ................................................................ 37
4 Table of Contents WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
6 Connect Devices ..................................................................................... 38
6.1 Connecting a Conductor to the CAGE CLAMP
®
................................... 38
6.2 Connection Examples ........................................................................... 40
6.2.1 1-Wire Connection, Protection Class I Actuators .............................. 40
6.2.2 1-Wire Connection, Protection Class II and III Actuators .................. 40
6.2.3 Operating the Relay in Separate Current Circuits ............................. 41
6.2.4 Operating the Relay in Series Connection ........................................ 42
6.3 Protective Circuits for Contacts of Relay Modules ................................ 43
7 Use in Hazardous Environments ........................................................... 45
7.1 Marking Configuration Examples .......................................................... 46
7.1.1 Marking for Europe According to ATEX and IECEx .......................... 46
7.1.2 Marking for the United States of America (NEC) and Canada
(CEC) ............................................................................................... 50
7.2 Installation Regulations......................................................................... 53
7.2.1 Special Notes Regarding Explosion Protection ................................ 53
7.2.2 Special Notes Regarding ANSI/ISA Ex ............................................ 55
List of Figures .................................................................................................. 56
List of Tables .................................................................................................... 57
=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =
WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 5
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 1/Hi nwei s e zu dies er D o kume ntati on - Über schr ift 1 @ 4\mod_1237987661750_21.docx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Sic her heit s- und sonstige Hinweise/Hinweis/Hinweis : Dokumentation aufbewahren @ 4\mod_1237987339812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten/ Ebe ne 2/G ültig kei tsb ereic h - Über schr ift 2 @ 12\mod_1338912448776_21.doc x @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on ( alt e Str uktur )/ Gül tig keits ber eic h/G ülti g keitsb erei ch D o kume ntat ion I/ O-Modul 750-xxxx, oh ne Vari anten angab e @ 14\mod_1358944037947_21.docx @ 109346 @ @ 1
This documentation is only applicable to the I/O module 750-517/040-000
(2DO 230V AC 1.0A/ Relay 2CO /XTR).
Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on ( alt e Str uktur )/H in weis e/A cht ung: Hi nw eis z ur D o kume ntati on I/O-M odul e 750- xxxx/040-000 @ 27\mod_1468502299549_21.docx @ 216892 @ @ 1
The I/O module 750-517/040-000 shall only be installed and operated according
to the instructions in this manual, in the system description for the WAGO-I/O-
SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750 XTR!
In addition to these operating instructions, you will also need the system
description “Design Notes XTR Guidelines and Recommendations for
Increasing Operational Safety” and the manual for the used fieldbus
coupler/controller, which can be downloaded at www.wago.com
. There, you can
obtain important information including information on electrical isolation, system
power and supply specifications.
Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Ur heb ersc hut z - Ü bersc hr ift 2 @ 23\ mod_1435647042188_21.docx @ 184808 @ 2 @ 1
1.2 Copyright
Pos: 12.2 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Ur heb ersc hut z au sf ührli ch @ 4\ mod_1235565145234_21.docx @ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12 .3 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
6 Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 12.4 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ S ymbol e - Ü ber schr if t 2 @ 13\ mod_1351068042408_21.docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/G efa hr/G efa hr: _War nu ng vor P ers on ensc hä den allg emei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son ensch äden d urch ele ktrisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule) /Sic herh eits - und so nst ige H i nweis e/ Warn ung/ War nung : _ War nu ng vor P ers one nsc häd en allg emei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Vorsic ht/V orsic ht: _War nung vor Pers one nschäd en allg emein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonsti ge Hin weise/ Achtu ng/A chtung : _War nung v or Sachsc häd en allg em ein _ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule) /Sic herh eits - und sonst ige Hi nweise/ Achtu ng/ Achtung : _War nung v or Sachsc häd en durc h elekt rostati sch e Aufla dung_ - Erläut erung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläut eru ng @ 13\mod_1343310326906_21. docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so nsti ge H in weis e/I nfor mat ion/ Inf or mati on: _W eiter e I nfor mat ion all ge mein_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1
WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 7
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 12.6 /Dokumentation allgemei n/Gliederungselemente/---Sei te nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
8 Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 12.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 2/ Dar st ellu ng der Z ahl ens yst eme - Über sc hrift 2 @ 2 3\mod_1435647128078_21.d ocx @ 184 811 @ 2 @ 1
1.4 Number Notation
Pos: 12.8 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Za hlens ys te me @ 3\mod_1221059454015_21.doc x @ 21711 @ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 12 .9 /All e Ser i en (Al lg emei ne M od ule)/ Über s chri fte n/Eb ene 2/ Schr ift kon venti on en - Ü bers chr ift 2 @ 23\ mod_1435647186005_21.docx @ 184814 @ 2 @ 1
1.5 Font Conventions
Pos: 12.1 0 / Alle Ser ie n (All ge mein e M odul e) /Re chtl ich es, Allg em ein es/Sc hr ift konv enti onen @ 3\mod_1221059521437_21.doc x @ 21714 @ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.:
File
>
New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.:
[F5]
Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 XTR Important Notes 9
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 14 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/Wi cht ige Erl äu ter unge n - Ü bers chr ift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Wi chtig e Er l äuter ung en - Ei nleit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15 .2 /All e Seri en (A llg emei ne M od ule) /Ü bers chri fte n/Eb ene 2/R ec htlic he Gr undlag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Änd er ungs vor beh alt - Über schr ift 3 und In halt @ 3\ mod_1221060036484_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/P erson alqu alifi kation/ Pers onalqu alifi katio n 750-xxxx - Ü ber schr ift 3 u nd I nh alt @ 3\ mod_1224061208046_21.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (WAGO-I/O-SYST EM )/ Wic htig e Er läut eru nge n (al te Str ukt ur)/B esti m mung sg emäß e Ver w end ung/ Bes ti mmung sg emäß e V er wendu ng 7 50- xxxx - Üb ersc hrift 3 @ 32\ mod_1536041141528_21.docx @ 498494 @ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Pos: 15.6 /Serie 750 (WAGO-I/O-SYST EM )/ Wic htig e Er läut eru nge n (al te Str ukt ur)/B esti m mung sg emäß e Ver w end ung/ Bes ti mmung sg emäß e V er wendu ng 7 50- xxx x für Gerät e - STD - mit EN 61000-6-3 @ 3 \mod_1224064151234_21.docx @ 24070 @ @ 1
Fieldbus couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to actuators or higher-level control systems. Using controllers, the signals can
also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler or controller.
10 Important Notes WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Appropriate housing (per 2014/34/EU) is required when operating the
WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a
prototype test certificate must be obtained that confirms the correct installation of
the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F-I/O modules within the modular
WAGO-I/O-SYSTEM 750. Only these safe F-I/O modules ensure functional
safety in accordance with the latest international standards. WAGO's
interference-free output modules can be controlled by the safety function.
Pos: 15.7 /All e Seri en ( All ge meine Mo dul e)/R ec htli ches , All ge mei nes /Te chni sc her Z us tand der Ger ät e - Ü bersc hri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
Repairs,
Changes to the hardware or software that are not described in the
operating instructions,
Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.8 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en/ Ebe ne 4/ E ntsor gen - Über schri ft 4 @ 30\ mod_1510145115652_21.docx @ 469859 @ 4 @ 1
2.1.4.1 Disposal
Pos: 15 .9.1 /Al le Seri en (All gemei ne Mod ule)/Ü bers chrift en/ Ebene 5/ Elektr o- und El ektr oni kg erät e - Üb ers chri ft 5 @ 3 2\mod_1537446988068_21.doc x @ 501657 @ 5 @ 1
2.1.4.1.1 Electrical and Electronic Equipment
Pos: 15.9 .2 /All e Ser ie n ( Allg emei ne Mod ule) /R echtl ich es , Allg em ein es/E le ktr o- un d Elektr onikg eräte @ 32 \mod_1532425086061_21. docx @ 491989 @ @ 1
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.
WAGO-I/O-SYSTEM 750 XTR Important Notes 11
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.
Observe national and local regulations for the disposal of electrical and
electronic equipment.
Clear any data stored on the electrical and electronic equipment.
Remove any added battery or memory card in the electrical and
electronic equipment.
Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
Pos: 15 .9.3 /D okum entati on allg emei n/Glie derung sele mente /----Leerz eil e-(1Z) ---- @ 28\mod_1485262995837_0.docx @ 404006 @ @ 1
Pos: 15 .9.4 /Al le Seri en (All gemei ne Mod ule)/Ü bers chrift en/ Ebene 5/ Verp ackung - Übers chri ft 5 @ 3 2\mod_1537447044202_21.doc x @ 501662 @ 5 @ 1
2.1.4.1.2 Packaging
Pos: 15 .9.5 /Al le Seri en (All gemei ne Mod ule)/R echtl iches , Allge mein es/V erpac kung @ 32 \mod_1537446786416_21.doc x @ 501653 @ @ 1
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
Observe national and local regulations for the disposal of packaging.
Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.
Pos: 15.1 0 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
12 Important Notes WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 15.1 1 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften /Eb ene 2/ Sich erh eits hin weis e - Ü bers chr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.1 2 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/E inl ei tung Sic her heit shi nw eise Har dwar e @ 6\ mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 3. 1 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : N ich t an G erät en unter S pann ung ar beite n! @ 6\ mod_ 1260180365327_21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.1 3. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /Gef a hr/G efahr : Pr od ukt nur i n ein em g eeig net en Geh äuse ei nba uen! @ 3 3\mod_1543581881435_21.docx @ 511972 @ @ 1
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
Guarantee that the max. permissible degree of pollution is not exceeded.
Offer adequate protection against contact.
Prevent fire from spreading outside of the enclosure.
Offer adequate protection against UV irradiation.
Guarantee mechanical stability
Restrict access to authorized personnel and may only be opened with tools
Pos: 15.1 3. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinwei se /Gef ahr /Gef ahr: Tr enn vorr ich tung un d Ü ber stro msc hutz @ 33\ mod_1543915978439_21.docx @ 512267 @ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Pos: 15.1 3. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : U nfal l verh ütung s vorsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1
Pos: 15.1 3. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /G efa hr/G efahr : A uf nor mger ec hte n Ansc hl uss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: 15.1 4 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/G ef ahr /Gef ahr: Lei tung en nur i n spa nnu ngs frei em Z ust and ans chl iess en oder tr enn en @ 16\mod_1372153982130_21.docx @ 124277 @ @ 1
WAGO-I/O-SYSTEM 750 XTR Important Notes 13
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Only connect or disconnect lines when power is safely isolated!
The lines to the device can carry hazardous voltages and currents. Contact with
the lines when live can result in severe injury or death. Therefore, read and
observe the following safety rules before you perform work on the device:
1. Disconnect the respective system component from the power supply.
2. Secure the system component against unintentional restart.
3. Check if the voltage is positively isolated.
Pos: 15.1 5 / Alle Ser ie n (All ge mein e M odul e) /Sic her hei ts- un d s onsti ge Hin wei se/V ors ic ht/Vor sic ht : H eiße Ober fl äc he nic ht ber ühre n! (all ge mein) @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos: 15.1 6. 1 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en (alt e St ruk tur) /Si cher hei ts- und s ons tig e Hi nwei se/ Ac htung /Ac ht ung: Ei nwa ndfr eie Ko nta ktier ung zur Trag sc hie ne g ew ährl eist en! @ 3 4\mod_1550481407638_21.doc x @ 530599 @ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 15.1 6. 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : D efe kte oder bes ch ädigt e Ger äte aust ausc hen! @ 6\ mod_1260180857358_21.doc x @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos: 15.1 6. 3 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Geräte vor kriechenden und isolierenden Stoffen schütze n! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos: 15.1 6. 4 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : R einig ung nur mi t zul äs sig en M at erial ien! @ 6\mod_1260181203293_21.doc x @ 46751 @ @ 1
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Pos: 15.1 6. 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755 @ @ 1
14 Important Notes WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 6. 6 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : V erpol ung en der Dat en- und Ver sorg ungsl eitu ngen ver meide n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15 .16. 7 /Alle S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und s o nstig e H inw eise /A chtu ng/A cht ung : El ektr ost atis ch e En tla dung v ermei de n! - DIN EN 61340-5-1/- 3 @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 15.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - un d son sti ge Hi n weis e/Ac ht ung/ Ac htung : XT R - Isol ati onspr üf ung en mit DC d urch fü hren! @ 15\mod_1370843209441_21.docx @ 122210 @ @ 1
Use only direct current (DC) for insulation testing!
Both the system voltage and field voltage side are capacitively coupled to the
DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage
between the DIN-rail and at least one of these two potentials can lead to the
destruction of the module.
Use only direct current (DC) for insulation testing. To avoid destroying the I/O
module, you must discharge it completely before applying the test voltage again.
Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 XTR Device Description 15
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 1/G erät e besc hrei bung - Ü ber schri ft 1 @ 3\mod_123375608 465 6_2 1.doc x @ 27 096 @ 1 @ 1
3 Device Description
Pos: 18.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger ätebesc hrei bung (al te Str uktur )/Einl eitu ng/An wendu ng/DO /Anw endung 750-05 xx DO Rel ais @ 5\ mod_1246611276875_21.doc x @ 36561 @ @ 1
The 750-517/040-000 Digital Output Module transmits binary control signals from
the automation device to the connected actuators (e.g., solenoid valves,
contactors, transmitters, relays or other electrical loads).
Pos: 18.2 /S erie 750 (WAGO-I/O-SYST EM) /Ger äte bes chr ei bung (alt e St ru ktur )/Ei nlei tu ng/I /O-B esc hrei bung /DO /I/O -Besc hr eibu ng 7 50- 0517 2 D O 2-Leit er (DO od er /DO ) @ 17 \mod_1384158208113_21.docx @ 136978 @ @ 1
The I/O module has 2 output channels, providing a direct connection to actuators.
The actuators can be wired directly to the CAGE CLAMP
®
connectors DO 1 or
/DO 1 (i.e. NOT DO 1) of channel 1 resp. DO 2 or /DO 2 (i.e. NOT DO 2) of
channel 2.
Pos: 18.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung/ I/O- Besc hrei bu ng/Al lge mei n/V er weis auf Kapi tel "An schl üss e" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " Ger ät e ans chl ieß en" > " Ansc hl ussb eis piel (e)" @ 5\mod_1246015203281_21.docx @ 36298 @ @ 1
Connection examples are shown in section “Connect Devices” >>
“Connection Example(s)”.
Pos: 18 .5 /Serie 750 (WAGO-I/O-S YSTEM) /Wic htige Er läut erung en (alt e Stru ktur)/Si cher heits - und sonstige Hinweise/Achtung/Achtung: DO Induktionsspannungsbegrenzung Relais @ 5\mod_1247031985231_21.docx @ 36766 @ @ 1
Inductive loads must be dampened!
For the protection of relay coils and contacts, inductive loads must be dampened
with an effective protection circuit!
Examples of protection circuits can be seen in the section Protective Circuits for
Contacts of Relay Modules.
Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr eibu ng/D O/I/ O-B esc hrei bung 75 0-0 5xx Wec hsler @ 5\ mod_1246866311313_21.docx @ 36609 @ @ 1
The I/O module incorporates 2 change-over relays connected potential free.
This means on the field side only the connections of the relay contacts are
present. Therefore, both relays can be operated with different voltages.
Because of the potential free contacts also a serial connection of the 2 relays is
possible as well as a serial connection of several relays with block wise
connection of several modules.
Pos: 18.7 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Einl eit ung /I/ O-Bes chr eibu ng/D O/I/ O-B esc hrei bung 75 0-0 517/ 040- 000 R elai sko nt akte 11 u nd 21 @ 2 2\mod_1425393378367_21.docx @ 1765 77 @ @ 1
The relay contacts 11 and 21 can be connected to an external voltage of
230 VAC resp. 300 VDC.
Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: Keine Verwe ndu ng von u nt erschi edl ic hen Pha sen ein es Dr eh stro mn etz es an bei de n Ka näl en @ 22\ mod_1425393912913_21.docx @ 176585 @ @ 1
No use of different phases of a three-phase system on both channels!
The max. voltage between adjacent connections may not exceed 250 VAC. The
use of different phases of a three-phase system on both channels of the relay
output module 750-517/040-000 is not permitted!
Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng ( alt e Str u ktur) /Ei nleit u ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bu ng 7 50-0 514, -517 Dur chsc hal tu ng d es mi ttl er en Rel ai sk onta ktes @ 2 2\mod_1425393644292_21.doc x @ 176581 @ @ 1
Depending on the relay status the voltage of the middle contact 11 resp. 21 is
switched to the lower contact 12 resp. 22 or to the upper contact 14 resp. 24. In
the OFF state the contacts 11 resp. 21 are switched to the lower contacts 12
resp. 22.
Pos: 18.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/Ei nl eitung /I/ O-Bes chr eib ung/D O/ I/O- Beschr eib ung 750- 05x x Ans te uer ung der R el ais ( Int ern e S yste msp ann ung) @ 5 \mod_1246861676649_21.docx @ 36599 @ @ 1
16 Device Description WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
The internal system voltage is used to trigger the relays.
Pos: 18.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebe schr ei bu ng (al te Stru ktur )/ Einl eit ung/ LED- Anzeige/LED Zustand Relais @ 5\mod_1246862048946_21.docx @ 36603 @ @ 1
The switching status of the two relays is indicated via green status LEDs.
Pos: 18.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng (al te Stru ktur) /Einl eitung /LED- Anz eige /V er weis a uf Kapit el " An zeig eel em ent e" @ 5\ mod_1246010525000_21.doc x @ 36194 @ @ 1
The meaning of the LEDs is described in the Display Elements” section.
Pos: 18.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/ Einl eit ung/ Vers org ung /A nordn ung unt er Ber üc ksic htig ung der Leis tu ngs kon takt e b elie big @ 3\ mod_1233756233468_21.docx @ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node.
An arrangement in groups within the group of potentials is not necessary.
Pos: 18.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herheit s- un d son stig e Hi n weis e/Hi nw eis/H in weis: P oten tial eins p eise modul für Er de ein setz en! ( keine LK f ür Erd e) @ 3\ mod_1226499037468_21.docx @ 25023 @ @ 1
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 18.1 5 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Hinweis/Hinweis: XTR - Er höht e S tör festi g keit @ 1 5\mod_1367496424993_21.docx @ 118330 @ @ 1
Increased interference!
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation,
field-side power supply filter 750-624/040-001 or power supply filter
750-626/040-000 are generally to be used for XTR module groups.
Pos: 18.1 6 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en (al te Stru kt ur)/S ic herhei ts - und sonstige Hinweise/Hinweis/Hinweis: XTR - Misc hbetri eb XTR/ Stan dard @ 1 5\mod_1367496420828_21.docx @ 118326 @ @ 1
Mixed operation
Mixed operation (standard/XTR modules) within a node is possible when groups
of modules are electrically isolated on the field side (i.e., electrically isolated
power supply).
Pos: 18.1 7 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung (al te Stru ktur )/ Einl eitung /Eins atzb ereic h/Eins atzb ereic h 750-xxxx/0 40-000 all e XT R-K oppl er/ Cont rol ler ohne Ei nsc hrä nkung +M isc hb etrie bhi nw eise @ 1 5\mod_1368425919479_21.docx @ 119444 @ @ 1
The I/O module can be operated with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750 XTR.
Observe the instructions for mixed operation when used in mixed operation
behind standard fieldbus couplers/controllers.
Pos: 19 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 XTR Device Description 17
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 20 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsi cht - Üb ersc hrif t 2 @ 4 \mod_1240984217343_21.docx @ 31958 @ 2 @ 1
3.1 View
Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsi cht/D O/ An sicht 75 0-0517/0040-xxxx @ 16\mod_1372413203476_21.docx @ 125117 @ @ 1
Figure 1: View
Pos: 22 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsi cht/ A nsich t C ageC lam p® _Leg en de mi t LE Ds _oh ne L eist ung sko nta kte @ 16 \mod_1371816091053_21.docx @ 124052 @ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > Connectors”
4
CAGE CLAMP
®
connectors
“Device Description” > Connectors”
5
Release tab
“Mounting” > Inserting and Removing
Devices”
Pos: 23 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
18 Device Description WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 24 /Alle Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nsc hlüs se - Üb erschr ift 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 25 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /Da ten kont akte /L okal bus - Ü b ersc hrif t 3 @ 6 \mo d_1256294684083_21.docx @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Local Bus
Pos: 26.1 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung (al te Str ukt ur)/ Ansc hlüs se /Da ten kon takt e - Fel d busko ppl er/-c ont roll er und Modul e Abbi ld ung un d Besc hr eib ung @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. The
contacting for the local bus consists of 6 data contacts, which are available as
self-cleaning gold spring contacts.
Figure 2: Data Contacts
Pos: 26.2 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: I/O-Modul e nicht a uf Goldf eder konta kte lege n! @ 7\ mod_1266318463636_21.docx @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 26.3 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und sonstige Hinweise/Achtung/Achtung: ESD - Auf Pote nti ala usgl eic h der U mgeb ung ac hte n! @ 32\ mod_1539077262331_21.docx @ 504433 @ @ 1
Pay attention to potential equalization from the environment!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, please ensure that
environmental factors (personnel, work space and packaging) are properly
equalized. Do not touch any conducting parts, e.g., data contacts.
Pos: 27 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 XTR Device Description 19
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 28 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str uktur) /Ansc hlüss e/Lei stung skont akte/F eld versor gung - Ü ber schri ft 3 @ 6\ mod_1256294692864_21.doc x @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /Lei stu ngs kont a kte ni cht vor ha nden @ 8\ mod_1281073936319_21.docx @ 62530 @ @ 1
The I/O module 750-517/040-000 has no power jumper contacts.
Pos: 30.1 /Serie 750 (WAGO-I/O-SYST EM) /Wic htige Er läuter unge n (alte Str ukt ur)/Sic her heits- und s onstig e Hin weise/ Hinw eis/Hi nweis : Pote ntialei nspei se modul ei nsetz en! (kei ne LK) @ 3\ mod_1226499089640_21.docx @ 25026 @ @ 1
Use a power supply module!
Use a power supply module for field-side power supply of downstream I/O
modules.
Pos: 31 /Dokumentatio n allge mein/ Glieder ungs elem ente/---S eite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/A nsc hlü sse /CA GE C LAM P-Ans chl üss e - Ü bersc hri ft 3 @ 6\mod_1256296337770_21.docx @ 43674 @ 3 @ 1
3.2.3 CAGE CLAMP
®
Connectors
Pos: 33 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung (al te Str uktur) /Ansc hlüss e/DO/ Ansc hlüss e 750-0517 @ 16\mod_1371808833394_21.docx @ 123957 @ @ 1
Figure 3: CAGE CLAMP
®
Connectors
Table 4: Legend for Figure “CAGE CLAMP
®
Connectors”
Channel
Designation
Connector
Function
1
14
1
Output DO 1: Normally open contact
11
2
Load line
12
3
Output /DO 1: Normally closed contact
2
24
5
Output DO 2: Normally open contact
21
6
Load line
22
7
Output /DO 2: Normally closed contact
Pos: 34 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
20 Device Description WAGO-I/O-SYSTEM 750 XTR
750-517/040-000 2DO 230V AC 1.0A/ Relay 2CO /XTR
Manual
Version 1.3.0
Pos: 35 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/A nzei g eele ment e - Ü ber schr ift 2 @ 4\ mod_1240984390875_21.doc x @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 36 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung (al te Str uktur) /Anz eigeel ement e/DO/ Anzei geele ment e 750-0 517 2 R O ( Agn, Egn) @ 16\mod_1372343976705_21.doc x @ 125054 @ @ 1
Figure 4: Display Elements
Table 5: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1
State
relay 1
A
off
Normally open contact DO1 opened
Normally closed contact /DO1
closed
Green
Normally open contact DO1 closed
Normally closed contact /DO1
opened
2
State
relay 2
E
Off
Normally open contact DO2 opened
Normally closed contact /DO2
closed
Green
Normally open contact DO2 closed
Normally closed contact /DO2
opened
Pos: 37 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n/Eb ene 2/B edi enel e ment e - Ü bers chri ft 2 @ 4\mod_1239191655456_21.docx @ 30439 @ 2 @ 1
3.4 Operating Elements
Pos: 38 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung (al te Str ukt ur)/B edi enel e ment e/Be di enele me nte I /O-Modul 75x-xxxx nicht vorhanden @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1
The I/O module 750-517/040-000 has no operating elements.
Pos: 39 /Doku ment ation all gemei n/Gli eder ungsel emente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

WAGO 2DO 230 V AC 1.0 A, Relay 2CO, potential-free /XTR User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI