Whirlpool AKR 641 GY Program Chart

Brand: Whirlpool

Model: AKR 641 GY

Category: Cooker hoods

Type: Program Chart

Whirlpool AKR 641 GY is an extractor hood which can be both installed as an extractor or as a filter. It features 3 different fan speed controls to provide sufficient extraction for different amounts of steam and fumes. The lamp cover can be opened using a small screwdriver or other suitable tool to replace the lightbulbs if they burn out. It is also possible to install carbon filters to reduce odors from cooking.



5019 318 33066

AKR 641 - AKR 643

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl-,

Kohlekochplatten). Befolgen Sie bei der Installation die Nummerierung

.....) und die jeweiligen Anleitungen. Schließen Sie das Gerät erst

nach erfolgter Installation an die Stromversorgung an. Achtung! Das Auslassrohr

und die Befestigungsmanschetten sind nicht im Lieferumfang inbegriffen und

müssen gesondert erworben werden.

INSTALLATION SHEET

Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To assemble follow the numbers (1

.....) and relative

instructions. Do not connect the appliance to the electrical power supply until

installation is completed. Warning! The exhaust pipe and clamps are not

supplied and must be bought separately.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique),

75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la

numérotation (1

.....) et les instructions correspondantes. Ne branchez

pas l'appareil tant que l'installation n'est pas terminée. Attention ! Le conduit

d'évacuation et les colliers de fixation ne sont pas fournis et doivent être achetés

à part.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 65 cm (elektrische

kooktoestellen), 75 cm (kooktoestellen op gas, gasolie of kolen). Volg

voor de montage de nummering (1

.....) en de bijbehorende

aanwijzingen. Geef het apparaat geen stroom totdat de installatie

geheel voltooid is. Let op! De afvoerbuis en de klembanden worden niet

bijgeleverd en moeten apart worden aangeschaft.

31833066.fm Page 1 Friday, December 20, 2002 9:47 AM



5019 318 33066

AKR 641 - AKR 643

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 65 cm (quemadores eléctricos), 75 cm

(quemadores a gas, gasóleo o carbón). Para efectuar el montaje siga la

numeración (1

.....) y las instrucciones. No conecte el aparato a la

corriente eléctrica hasta que la instalación esté completamente finalizada.

¡Atención! El tubo de descarga y las guías no están incluidas y se compran aparte.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 65 cm (fogões eléctricos), 75 cm (fogões a gás,

óleo ou carbono). Para a montagem, siga a numeração (1

.....) e as

respectivas instruções. Não ligue o aparelho à corrente eléctrica até a instalação

estar concluída. Atenção! O tubo de descarga e as tiras de fixação não são

fornecidas e devem ser compradas à parte.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas,

gasolio o carbone). Per il montaggio seguire la numerazione (1

.....) e le

istruzioni relative. Non dare corrente allapparecchio finché linstallazione non è

totalmente completata. Attenzione! Il tubo di scarico e le fascette di fissaggio

non sono fornite e vanno acquistate a parte.

ùüùü+ùùùþ

ü$12.)12.1.)2"0120"FP02!"0120"FP0120"

.0! #02!0. #0! #.+.22  21.  #1202

.!1





.2"1$02" /0"2! 3 / 2020002!)

!0*.21#10#!2  !&12"0.212.1"! 1 $

1&."..&".2. !.120!&1"/0/.202..!0.

. 2 *$&!12

31833066.fm Page 2 Friday, December 20, 2002 9:47 AM



5019 318 33066

AKR 641 - AKR 643

31833066.fm Page 3 Friday, December 20, 2002 9:47 AM



5019 318 33066

AKR 641 - AKR 643

31833066.fm Page 4 Friday, December 20, 2002 9:47 AM



5019 318 33066

AKR 641 - AKR 643

Preliminary information for installing the hood:

Disconnect the power supply at the domestic main switch before carrying out electrical connections.

1. Fix 2 support brackets D (Fig. 1) to the sides of the wall unit (one each side) using 2 screws per bracket

(the brackets must be parallel with the lower edge of the unit).

Position the support bracket so that it is against the back of the wall unit, making sure that the rear edge

of the bracket matches the back of the hood.

Drill an opening at the top of the wall unit for the exhaust pipe and the power supply cable.

2. Fix 2 support brackets E (Fig. 2) to the sides of the hood (one each side).

a. Pull out the deflector;

b. Remove the grease filter/s;

c. From the inside of the hood, secure the support brackets using two screws P per bracket, making

sure to place the brackets as high as possible (near the outlet duct), then tighten the screws.

3. Fit the hood inside the wall unit, being careful to position the hood bracket E above the wall unit bracket

D (Fig. 1-2).

Insert the power supply cable through the opening made for the purpose.

4. Secure the hood with two screws in front (Fig. 3 - one each side).

5. Carry out the electrical connection to the mains power supply, only turn on the power supply with

assembly completed.

6. If necessary, adjust the alignment by loosening the screws P of the brackets E mounted on the hood

(Fig. 2) until the hood and the lower edge of the wall unit line up perfectly, then tighten the screws again.

7. Adjust the deflector slideout stroke according to the depth of the wall unit by adjusting the two

retainers F (Fig. 5). In this way the front will be perfectly aligned with the wall unit.

a. Loosen the screws of the retainers F;

b. Adjust by moving the retainers backwards or forwards;

c. Tighten the screws of the retainers.

8. Fix an outlet duct to the collar C supplied. The outlet duct diameter should be the same as that of the

collar (Fig. 4). The exhaust pipe must be long enough to vent externally (extractor version) or must reach

the top of the wall unit (filter version).

9. Fix the collar C (snap-close) to the top section of the hood discharge.

To facilitate installation, the collar has a mark G that must match the specific guide H on the exhaust

duct.

10. Complete the installation of the exhaust duct.

Refit the grease filter/s, connect the hood to the power supply and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

D F NL E

P I GR

31833066.fm Page 7 Friday, December 20, 2002 9:47 AM



5019 318 33066

AKR 641 - AKR 643

1. Control panel.

2. Grease filter (1 or 2 pieces depending on model).

3. Grease filter spring release handles.

4. Lighting unit.

5. Pull-out steam deflector.

6. Extractor unit body.

Removing and/or washing the grease

filter/s

1. Disconnect the electrical power supply.

2. Remove the dirty grease filter/s by pulling the

handle first backwards and then downwards

(Fig. 1).

3. After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface

is covered.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool

to prise off the lamp cover (Fig. 2).

3. Remove the burnt-out bulb.

4. Replace using 40 W max E14 bulbs only.

5. Replace the lamp cover so that it clicks into

position.

Fitting or renewing the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter/s (Fig. 1).

3. If the carbon filters are already mounted (one or

two filters, depending on the model, covering the

motor protection grille) and need renewing, turn

the central handle (Fig. 3 - c) anticlockwise until

the filters release.

4. If the carbon filters are not already mounted,

locate the filters to cover the motor protection

grilles (two protection grilles - two carbon filters,

one protection grille - one carbon filter), then

turn the central handle (Fig. 3 - c) of the filters

clockwise.

5. Refit the grease filter/s (Fig. 1).

CONTROL PANEL

Light switch.

The switch has two positions

(lights OFF - lights ON).

To switch on the lights: move the switch to the

right.

Motor switch.

The extraction speed switch has 3 settings,

depending on the amount of steam and fumes.

To increase the extraction speed: move the

switch to the right.

Fig. 1

Fig. 2

Fig. 3

PRODUCT SHEET

D F NL E

P I GR

31833066.fm Page 8 Friday, December 20, 2002 9:47 AM

Whirlpool AKR 641 GY Program Chart

Brand: Whirlpool

Model: AKR 641 GY

Category: Cooker hoods

Type: Program Chart

Download PDF

report

Whirlpool AKR 641 GY Program Chart

Whirlpool AKR 641 GY Program Chart

Related papers

Other documents