AKR 912
5019 100 75102
INSTALLATIONSANGABEN
Mindestabstand zur Kochfläche: 65 cm (Elektroplatten), 75 cm (Gas-, Öl-,
Kohlekochplatten)
INSTALLATION SHEET
Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil
or coal cookers)
FICHE D'INSTALLATION
Distance minimale par rapport à la cuisinière : 65 cm (cuisinière électrique),
75 cm (cuisinière à gaz, mazout ou charbon)
INSTALLATIESCHEMA
Minimum afstand van het kooktoestel: 65 cm (elektrische kooktoestellen),
75 cm (kooktoestellen op gas, olie of kolen)
FICHA DE INSTALACIÓN
Distancia mínima de los quemadores: 65 cm (quemadores eléctricos),
75 cm (quemadores a gas, gasóleo o carbón)
FICHA DE INSTALAÇÃO
Distância mínima dos fogões: 65 cm. (fogões eléctricos), 75 cm. (fogões a
gás, óleo ou carbono)
SCHEDA INSTALLAZIONE
Distanza minima dai fuochi: 65 cm (fuochi elettrici), 75 cm (fuochi a gas,
gasolio o carbone)
ù(ù ü+ù$ùþ
ü$12.)12.1.)2"0120"FP02!"0120"FP0120"
.0! #02!0. #0! #.
D
GB
F
NL
E
P
I
GR
5019 100 75102
AKR 912
F
13F
4
5
6
1
3
3
9
9
10
10
7
7
8
8
2
11
11
12
12
13
14
14
17
17
15
16
18
Wird nicht mitgeliefert
Not provided
Non fourni
Niet geleverd
No suministrado
Não fornecido
Non fornito
û0$ !02.
5019 100 75102
AKR 912
2
5
3
1
4
4
1.
Control panel
2.
Grease filter
3.
Grease filter handle
4.
Lighting unit
(Halogen bulb)
5.
Telescopic flue
CLEANING THE GREASE FILTER
Wash the grease filter at least once a month,
or whenever the grease filter saturation indicator
flashes (Extraction speed indicator
2
).
1.
Unplug the appliance or switch off the mains
power supply.
2.
Remove the grease filter:
a
- pull the handles towards the centre of the
filter
b
- and then downwards.
3.
After washing the metal grease filter,
remount in reverse order ensuring that the
entire extraction surface is covered.
REPLACING BULBS
1.
Unplug the appliance or switch off the mains
power supply.
2.
Using a screwdriver or any other suitable
tool, prize off the lamp cover.
3.
Remove the burnt-out bulb.
Use 20W max halogen bulbs only, making
sure not to touch them with your hand.
4.
Replace the lamp cover (clicking it into
position).
FITTING OR RENEWING THE CARBON
FILTER
1.
Unplug the appliance or switch off the mains
power supply.
2.
Remove the grease filter (
a
,
b
).
3.
Fit the carbon filter, fixing it with the two
screws supplied (
c
).
4.
If the carbon filter needs renewing, remove
the old filter and fit a new one.
Change the carbon filter at least once a year
and, in any event, every time the carbon filter
saturation indicator flashes (Extraction speed
indicator
3
).
5.
Refit the grease filter.
Reset filter indicator:
Press the button OFF
until LED
2
and/or LED
3
stop flashing.
CONTROL PANEL
1.
Extraction OFF button.
2.
Extraction ON speed increase button -
1
Ö
3
Ö
1...
3.
Extraction speed indicator
1
.
4.
Extraction speed indicator
2
and grease filter
saturation indicator (when flashing).
5.
Extraction speed indicator
3
and carbon filter
saturation indicator (when flashing).
This indicator is usually deactivated to
activate it, press button
1
, then,
simultaneously, buttons
2
and
7
until the
carbon filter saturation indicator starts
flashing; to deactivate it, repeat the steps
above until the carbon filter saturation
indicator stops flashing.
6. Intensive
extraction speed indicator.
7.
Intensive speed button (timed): the hood
operates at this speed for 5 minutes and
then returns to the previous settings.
This function can be cancelled by pressing
button
1
or
2
.
8.
Light OFF button.
9.
Light ON button.
1234567 89
a
b
CC
PRODUCT DESCRIPTION SHEET
F NL E PGBD GRI
/