Page is loading ...
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
NOTE: Allow 1-1/4" between unit end supports
when installation calls for multiple stacked units
and/or shelves.
1. Install shelf ends and lower shelf per Shelf
Installation Instructions.
2. Start screws (provided) in brass inserts in end
panels. Do not tighten screws before installing
shelf.
3. Note elongated slot at the rear of top panel end.
Slide top panel downward over rear screw
shank. Adjust top panel and slide downward
over front screw shank (Fig. 1). Tighten screws
firmly.
4. Check flipper door operation. Lateral adjustment
can be made by loosening screws on slide
hinge, center the door and tighten screws firmly
(Fig. 2).
7021-6491 B
1 of 3
238-181
PLACES/UniGroup®
OVERHEAD STORAGE UNIT
In s ta lla tio n In s tr u c tio n s
FIG . 1
SPE C IAL #10-24x3/8"
MACHINE SCREW
ELONGATED
SLO T
FIG . 2
Part No: Rev:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
Wood Overhead Storage Unit
1. Brackets are assembled to end panels with two
(2) #10-24 x 3/8" machine screws on each side.
Narrow side of bracket must be against end
panel (Fig. 3).
2. End panels are inserted into panel slots at
desired height.
NOTE: To seat panel fully, a mallet may be
required. However, caution is needed so as not to
damage wood.
3. End panels are properly installed when retention
lock (Fig. 3) engages into side rail.
4. Bottom shelf should slide into place from front,
jut above brackets. Shelf is then placed down
on brackets and secured with two (2) #10-12 x
5/8" wood screws (Fig. 3). Do not drop shelf
down onto brackets from top.
7021-6491 B
2 of 3
238-181
RETENTION
LO C K
5. Top shelf (with door) is placed down onto
brackets and secured with two (2) #10-12 x 5/8"
wood screws on each side (Fig. 3). Elongated
holes in brackets permit adjustability of top and
bottom shelves in order to flush door front with
end panels (Fig. 4).
NOTE: When two overhead storage units are
installed one above the other, the top unit must be
installed first.
6. Check flipper door operation. Adjustment can be
made by loosening screws on slide hinge, make
lateral adjustment to center door and retighten
screws firmly (Fig. 2).
END PANELS
SPE C IAL #10-24 x 3/8"
MACHINE SCREW
FLIPPER
DOOR
#10-12 x 5/8"
WOOD SCREW
(B L A C K )
BO TT OM
SHELF
TO P SHELF
ADJUST FOR
FLUSH FRONT
FIG . 3
FIG . 4
Special Keying
NOTE: Lockable components are shipped
without lock plugs installed. Lock plug
installation is identical with or without Special
Keying.
Keyed Alike and Master Key Only
1. From the installation instruction drawings,
determine the Work Station/Location
numbers (SK-1 to SK-50) assigned to the
various areas.
2. Count the number of lockable components
in the area where installation is to begin and
identify the Haworth Key Number associated
with that area from the Haworth Special
Keying Order Form.
3. Acquire the determined quantity of assigned
lock plugs for that area, according to the
Haworth Key Number.
Lock Plug Installation
4. Remove the key which came already
inserted in the lock plug (Fig. 1).
5. Insert the Control Key into the lock plug to
be installed.
6. Insert the lock pug into the lock shell of the
component (Fig. 2).
7. Hold the lock plug in place with your thumb
and remove the Control Key (Fig. 3).
8. Replace the original key into the inserted
lock plug.
CONTROL KEY
STANDARD KEY
FIG. 2
FIG. 1
Part No: 7021-6491 Rev: B
Page: 3 of 3
E.C.O. No: 238-181
CUSTOMER SERVICE PHONE: 1-800-426-8562
FIG. 3
/
