2. Haworth
  3. BELONG

Haworth BELONG, 7029-9923 Installation guide

  • Hello! I have reviewed the installation instructions for the BELONG Multi Material Territory Screen. This document provides step-by-step guidance on how to assemble and mount the screen, emphasizing precautions about the adhesive and the correct usage of the retainer to prevent glass damage. I am ready to answer any questions you may have about the installation process.
  • What should I do before attaching the screen?
    What precaution should I take with the tape?
    What should I do if I'm reusing the retainer?
ASTM
TEMPERED
LOGO
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
2420-126 1 of 4 7029-9923
Tools Required
Multi Material Territory Screen
Installation Instructions
BELONG®
1
3/32"
Allen Wrench
Isopropyl
Alcohol
AScreen
BScreen
Tape Strip
D
Nut Plate
Assembly
ECover
FBase
G
Double Sided Tape
H
Retainer
CEnd Cap
IF REUSING RETAINER (H)
MAKE SURE THE MARKED
SIDE IS FACING AWAY
FROM THE GLASS.
CAN CAUSE FAILURE OF
GLASS SCREENS
CAUTION
Foam Tape
D1
1
ISOPROPYL
ALCOHOL
ISOPROPYL
ALCOHOL
A1
A1
3
4
1
2
G
NOTE: Wipe mounting surface area
with Isopropyl Alcohol to ensure
area cleaned and achieve full bond.
CAUTION: TAPE (G) IS VERY
AGGRESSIVE. DETERMINE
FINAL POSITION OF SCREEN
BEFORE ADHERING TO
WORKSURFACE. ALLOW 72
HOURS TO FULLY CURE.
FOR
FABRIC
FOR
SOLID
H
Scale 1 : 1
011/2
1/4 1/4
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
2420-126 2 of 4 7029-9923
ASTM
TEMPERED
LOGO
1Use tape (B1) to mark location
2Install Screen Tape Strip (B)
3
B
NOTE: Center screen tape strips (B)
with center of tape (B1) and apply ush
with bottom of screen (A).
NOTE: Locate tape (B1) centering with
each tab shown on base (F1).
A
B
B1
0.0” 0.01”
NOTE: Tempered
Glass Logo is always
on the bottom.
B1
F1
REMOVE TAPE (B1)
ONCE TAPE STRIPS (B)
ARE INSTALLED!
ASTM
TEMPERED
LOGO
Install Nut Plate Assembly (D) and Foam Tape (D1)
4
D
D
D1
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
2420-126 3 of 4 7029-9923
1
PLUMB SCREEN (A)
A
A
F
IF REUSING RETAINER (H)
MAKE SURE THE MARKED
SIDE IS FACING AWAY
FROM THE GLASS.
CAN CAUSE FAILURE OF
GLASS SCREENS
CAUTION
WARNING! WARNING!
TIGHTEN FIRMLY OR UNTIL
ALLEN WRENCH FLEXS.
(NOT TO EXCEED 15in lbs)
Install screen (A)
5
2 SNUG ALL SET SCREWS
F
NOTE: Make sure retainer (H)
is in between screen and set
screws of nut plate (D).
H
BD
(No Gaps) 0.0"
H
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
2420-126 4 of 4 7029-9923
A
A
HINT: Make sure the screen (A)
is aligned, plumb, and centered
BEFORE installing covers (E).
6
7
E
F
C
2
1
E
C
/