ROSE DISPLAYS AnoQuick Instruction Sheet

Brand: ROSE DISPLAYS

Model: AnoQuick

Type: Instruction Sheet

ROSE DISPLAYS AnoQuick is a convenient and reusable hanging system for posters, prints, and other lightweight signage. With its easy-to-use components and straightforward instructions, AnoQuick makes it simple to create professional-looking displays in minutes.

AnoQuick consists of several key parts: AnoQuick Holder, MultiClips, Crimp Sleeves, End Caps, and Cable and Ball. By following the five simple steps outlined in the instruction sheet, you can quickly assemble AnoQuick and hang your graphics securely.

The AnoQuick system is versatile and can be used in a variety of settings, including offices, schools, retail stores, and exhibition halls. It is perfect for displaying posters, prints, photographs, menus, and other lightweight signage.

Parts

Instructions For Hanging

Instruction Sheet

Step 1

Prepare edges of graphic. Place the graphic on

tabletop with one edge at the table edge. Using

the AnoQuick Holder, run it across the graphic

edge, crushing it slightly. Fig. 1

Step 2

Starting at one corner, push the holder onto the

graphic. Work your way down the holder tapping

it down firmly to seat the graphic fully. Fig. 2

Step 3

Slide MultiClip into top of AnoQuick Holder.

Holding clip at slight angle, first insert one

round end, then press down on other round

end and push MultiClip into holder. Insert

second MultiClip. Fig. 3

Place each MultiClip about 1/3 from the edge of

the poster. Fig. 4

Step 4

Use Crimp Sleeves to form a loop to secure the

cable to the MultiClip. Fig. 5

Use pliers to crimp the sleeve securely to form the

loop. Trim any excess cable after crimping.

Step 5

Push end caps into place. Fig. 6

Important note:

Please save and reuse the AnoQuick Holder,

End Caps and MultiClips for future projects.

AnoQuick™

Incept-8.15.02

Figure 2

The AnoQuick is a registered trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products. Part

#02INSAnoQuickLoopBall

Figure 3

Figure 5

Figure 1

End Caps

06-5525

AnoQuick

12A300

MultiClips

1UP-0100

Cable

and Ball

16-0018B

Crimp Sleeves

80-0101

Figure 6

Figure 4

35 Congress Street, Salem MA 01970

Tel# 1-800-631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Parts

Instructions For Hanging

Instruction Sheet

Step 1

Prepare edges of graphic. Place the graphic on

tabletop with one edge at the table edge. Using

the AnoQuick Holder, run it across the graphic

edge, crushing it slightly. Fig. 1

Step 2

Starting at one corner, push the holder onto the

graphic. Work your way down the holder tapping

it down firmly to seat the graphic fully. Fig. 2

Step 3

Slide MultiClip into top of AnoQuick Holder.

Holding clip at slight angle, first insert one

round end, then press down on other round

end and push MultiClip into holder. Insert

second MultiClip. Fig. 3

Place each MultiClip about 1/3 from the edge of

the poster. Fig. 4

Step 4

Use Crimp Sleeves to form a loop to secure the

cable to the MultiClip. Fig. 5

Use pliers to crimp the sleeve securely to form the

loop. Trim any excess cable after crimping.

Step 5

Push end caps into place. Fig. 6

Important note:

Please save and reuse the AnoQuick Holder,

End Caps and MultiClips for future projects.

AnoQuick™

Incept-8.15.02

Figure 2

The AnoQuick is a registered trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products. Part

#02INSAnoQuickLoopBall

Figure 3

Figure 5

Figure 1

End Caps

06-5525

AnoQuick

12A300

MultiClips

1UP-0100

Cable

and Ball

16-0018B

Crimp Sleeves

80-0101

Figure 6

Figure 4

ROSE DISPLAYS AnoQuick Instruction Sheet

ROSE DISPLAYS AnoQuick Instruction Sheet

ROSE DISPLAYS AnoQuick Instruction Sheet

Related papers

Other documents