Vicoustic 2380x1190x20mm Installation guide

Type
Installation guide

Vicoustic 2380x1190x20mm is a flat panel designed for acoustic treatment, providing sound absorption and noise reduction. It can be easily installed on walls using Flexi Glue Ultra, and can be combined with Aluframe VMT accessories for a seamless look. The product is suitable for a variety of applications, including studios, home theaters, offices, and other environments where acoustic control is desired.

Vicoustic 2380x1190x20mm is a flat panel designed for acoustic treatment, providing sound absorption and noise reduction. It can be easily installed on walls using Flexi Glue Ultra, and can be combined with Aluframe VMT accessories for a seamless look. The product is suitable for a variety of applications, including studios, home theaters, offices, and other environments where acoustic control is desired.

EN
Flat Panel VMT
2380x1190x20mm
Installation Manual
EN
Not Included
Level
MATERIAL NEEDED
Included
Flat Panel VMT 2380x1190x20mm
Measuring Tape Box Cutter
Velcro Stripes
Flexi Glue Ultra
Aluframe VMT T, Double or Single
*This product should be handled by two installers.
Cutting Tools
EN
Apply Flexi Glue Ultra on the back of the acoustic panel, near the edges. Do not
wait longer than 10 minutes after applying the glue to attach the panel to the wall.
Place the panel on the suitably chose position on the wall. Once in the desired
place, press rmly against the wall for 15 seconds.
1
2
!To ensure that you maximise the strength of the glue, don’t make any adjustments
to the panel after bonding
EN
1
2Based on the smallest height, calculate if it is necessary to cut
one of the panels to ll the entire wall height. Check for continuity
between panels before cutting.
Measure wall height in both sides. Take the smallest height.
??
Full wall installation
B
EN
3
4Start the installation from the bottom-right side (If cuted panels
are going to be used it is recommended to start with these). Check if
panels are levelled before proceding to next row.
Glue the panels directly to the wall with Flexi Glue Ultra.
EN
!You can also install this panels with Aluframe VMT 20 single or double.
For more detailed information about Aluframe VMT installation, please
refer to the installation manual.
5You can use the Aluframe VMT T, to hide the joints between the panels.
EN
!Do not apply Flat Panel VMT behind radiators or too close to a heat
source.
© Vicoustic, 2023 | V3
No parts of this document might be copied and/or published without written consent of Vicoustic.
Main Oce, R&D & Logistics
Avenida do Pólo 3, Nº 159, Carvalhosa
4590-137 Paços de Ferreira, Portugal
Oce
Rua Quinta do Bom Retiro Nº 16, Armazém 9
2820-690 Charneca da Caparica, Portugal
T (+351) 212 964 100
Info and Sales
E sales@vicoustic.com
www.vicoustic.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vicoustic 2380x1190x20mm Installation guide

Type
Installation guide

Vicoustic 2380x1190x20mm is a flat panel designed for acoustic treatment, providing sound absorption and noise reduction. It can be easily installed on walls using Flexi Glue Ultra, and can be combined with Aluframe VMT accessories for a seamless look. The product is suitable for a variety of applications, including studios, home theaters, offices, and other environments where acoustic control is desired.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI