VicAudiophile

Vicoustic VicAudiophile Installation guide

  • Hello! I've reviewed the installation manual for the VicAudiophile VMT Kit. This manual provides detailed instructions on how to install the acoustic panels on walls and ceilings, including how to use the included fixings, glues and profiles. I'm ready to answer any specific questions you might have about the installation process or the components of the kit.
  • What components are included in the VicAudiophile VMT Kit?
    How can I install the Flat Panel VMT on the wall?
    Is glue required for ceiling installation?
    What is the purpose of using blocking element?
1
EN
VicAudiophile VMT Kit
Installation Manual
EN
3
Not Included
MATERIAL NEEDED
Included
Wall Plugs and Screws
VicFix Corner 2+2
Flat Panel VMT x4 VicPET Wool x8
DrillLevel Measuring Tape
6mm Phillips Screwdriver
VicSpacer x4
VicFix J Prole 80mm | 3.14" x4
Multifuser 64 x2
VicPattern Ultra x4 VicFix J Prole 595mm | 23.4" x6
Flexi Glue Ultra
Caulking Gun
EN
4
VicSpacer Installation
Mark the drill holes of the VicSpacers according to the diagram.
In the case of installing two or more units, pay attention to the spacing between
units. The dimensions marked between VicSpacers are for use of only one metal joint
between them.
575 mm
800 mm
22 mm
1
2
Wall Installation
EN
5
3
EN
6
2
Mark the drill holes of the VicSpacers according to the diagram.
In the case of installing two or more units, pay attention to the spacing between
units. The dimensions marked between VicSpacers are for use of only one metal joint
between them.
Ceilling Installation
1
575 mm
800 mm
22 mm
EN
7
3
1
Flat Panel VMT Installation
EN
8
3
2For wall installation and if you do not want a permanent xation of the Flat Panel
VMT, you can apply the panel directly to the Vicspacer, inserting it inside the
metal frame. If you want a more secure and permanent xation, x the Flat Panel
VMT with Flexi Glue Ultra by applying a bead of glue to the surface of the plywood
structure and pressing it, to ensure an even and precise adherence. For ceiling
installation, the Flat Panel VMT must be glued with Flexi Glue Ultra.
EN
9
406 mm | 15.984"
2
1
VicFix Corner Installation
EN
10
1
VicPattern and Multifuser Wood MKII 64 Wall Installation
Dene where you want to install the panels and start marking the drill holes for
xing the proles to the wall.
257,5 mm
80 mm
2
1
3
EN
11
4
575 mm
5
23
Turn the panels on their
back and apply the silicone
drops as indicated in the
diagram.
Steps Material
EN
12
98
2
1
1
2
67
EN
13
1312 2
1
2
1
1110
2
1
2
1
!Please note: It is recommended to apply a blocking element such as a L prole or a small screw to
avoid the end panels to slide off the VicFix J prole.
16
Main Oce, R&D & Logistics
Avenida do Pólo 3, Nº 159, Carvalhosa
4590-137 Paços de Ferreira, Portugal
Oce
Rua Quinta do Bom Retiro Nº 16, Armazém 9
2820-690 Charneca da Caparica, Portugal
T (+351) 212 964 100
Info and Sales
E sales@vicoustic.com
www.vicoustic.com
© Vicoustic, 2021 | V3
No parts of this document might be copied and/or published without written consent of Vicoustic.
1/13