Barco Light Shutter for SLM Series Installation guide

B AR CO PR OJ E C TION S YS TE MS

Date: 24.02.2004

INS TAL L ATION MANUAL

K it L ight S hutter for S L M projector

R 9841160

Art. No.: R 5976306R ev: 01

L ight S hutter

S LM

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, September 2001.

Trademarks are the rights of their respective owners.

BARCO n.v./Projection Systems

Noordlaan 5

B-8520 Kuurne

Belgium

Tel : +32/56/368211

Fax : +32/56/351651

E-mail : [email protected]

Visite Barco at the web : http://www.barco.com

Printed in Belgium

Contents

Safety ................................................................................................................................................................ 5

Who....................................................................................................................................................................................................................5

General .............................................................................................................................................................................................................. 5

Contents of the Kit ........................................................................................................................................... 6

Contents ............................................................................................................................................................................................................ 6

Light Shutter disposal ........................................................................................................................................................................................ 6

Part Listing......................................................................................................................................................................................................... 6

Illustration of the Kit ........................................................................................................................................................................................... 6

Removing the Electronic Box.......................................................................................................................... 7

What has to be done .........................................................................................................................................................................................7

Necessary Tools ................................................................................................................................................................................................ 7

Removing the Electronic Box ............................................................................................................................................................................ 7

Illustrations ........................................................................................................................................................................................................ 7

Removing SM Power Supply cover ................................................................................................................ 8

What has to be done .........................................................................................................................................................................................8

Necessary Tools ................................................................................................................................................................................................ 8

Removing the side panel................................................................................................................................................................................... 8

Illustrations ........................................................................................................................................................................................................ 8

Removing the Lamp Unit cover. ...................................................................................................................... 9

What has to be done .........................................................................................................................................................................................9

Necessary Tools ................................................................................................................................................................................................ 9

Removing the side panel................................................................................................................................................................................... 9

Illustrations ........................................................................................................................................................................................................ 9

Removal of the Back Cover ........................................................................................................................... 10

What has to be done .......................................................................................................................................................................................10

Necessary Tools .............................................................................................................................................................................................. 10

Removing the back cover................................................................................................................................................................................ 10

Illustrations ...................................................................................................................................................................................................... 10

Removal of the Top Cover ..............................................................................................................................11

What has to be done ....................................................................................................................................................................................... 11

Necessary Tools .............................................................................................................................................................................................. 11

Removing Top cover........................................................................................................................................................................................ 11

Illustrations ...................................................................................................................................................................................................... 11

Removal of the Top Cover (Continued) ........................................................................................................ 12

Removing Top cover........................................................................................................................................................................................ 12

Illustrations ...................................................................................................................................................................................................... 12

Installing the Light Shutter Assembly .......................................................................................................... 13

What has to be done .......................................................................................................................................................................................13

Necessary Tools .............................................................................................................................................................................................. 13

Mounting the Light Shutter .............................................................................................................................................................................. 13

Illustrations ...................................................................................................................................................................................................... 13

Illustrations ...................................................................................................................................................................................................... 14

Installing the Light Shutter Assembly (continued)...................................................................................... 14

Electrical Connection of the Light Shutter................................................................................................... 15

What has to be done .......................................................................................................................................................................................15

Connection of the Light Shutter....................................................................................................................................................................... 15

Illustrations ...................................................................................................................................................................................................... 15

Reinstalling the Top Cover ............................................................................................................................ 16

What has to be done .......................................................................................................................................................................................16

Necessary Tools .............................................................................................................................................................................................. 16

Mounting the Top cover ................................................................................................................................................................................... 16

Illustrations ...................................................................................................................................................................................................... 16

Reinstalling the Top Cover (Continued) ....................................................................................................... 17

Mounting the Top cover ................................................................................................................................................................................... 17

Illustrations ...................................................................................................................................................................................................... 17

Reinstalling the Back Cover .......................................................................................................................... 18

What has to be done .......................................................................................................................................................................................18

Necessary Tools .............................................................................................................................................................................................. 18

reinstalling the back cover.............................................................................................................................................................................. 18

Illustrations ...................................................................................................................................................................................................... 18

Reinstalling the Lamp Cover ......................................................................................................................... 19

What has to be done .......................................................................................................................................................................................19

Necessary Tools .............................................................................................................................................................................................. 19

Reinstalling the side panel .............................................................................................................................................................................. 19

Illustrations ...................................................................................................................................................................................................... 19

Reinstalling the Electronic Box..................................................................................................................... 20

What has to be done .......................................................................................................................................................................................20

Necessary Tools .............................................................................................................................................................................................. 20

Reinstalling the Electronic Box........................................................................................................................................................................ 20

Illustrations ...................................................................................................................................................................................................... 20

Installation of the SM Power Supply Cover ................................................................................................. 21

What has to be done .......................................................................................................................................................................................21

Necessary Tools .............................................................................................................................................................................................. 21

Reinstalling the cover ......................................................................................................................................................................................21

Illustrations ...................................................................................................................................................................................................... 21

BARCO  5  Projection Systems

Safety

Who This installation must be performed by authorized technical personnel* only.

General

CAUTION

Before attempting to remove any of the projectors covers, the

projector has to be turned off and disconnected from the wall

outlet to minimize the risk of electric shock.

Before starting with the installation of the Light Shutter, always let

cool down the projector after operation in order to reduce the heat

on parts in the light path and to avoid burns.

WARNING

Eye damage may result from direct viewing the light produced by the lamp used in this

equipment. Always turn off lamp before opening cover.

PRODUCT CARE

Installation Kit: - The Kit R9841160 - Light Shutter - is designed for use ONLY with

the BARCO SLM series projectors.

Replacement parts - When replacement parts are required, be sure the service

technician has used original BARCO replacement parts or authorized replacement

parts which have the same characteristics as the BARCO original part.

Unauthorized substitutions may result in degraded performance and reliability, fire,

electric shock or other hazards. Unauthorized substitutions may void warranty.

Under no circumstances are BARCO parts repairable by anyone other than BARCO.

* Authorized technical personnel: persons having appropriate technical training and

experience necessary to be aware of hazards to which they are exposed in performing

a task and of measures to minimize the danger to themselves or other persons.

BAR CO ——————————————————— 6 ————————————— Projection S ystems

C ontents of the K it

C ontents The kit contains a C omplete Light S hutter unit.

L ight S hutter

dis pos al

To dispose of the defective units, return the unit to B AR C O in a complete original

packaging. This way is the kindest to the environment.

The Light S hutter does not contain any materials which is harmful to the environment

so it is not subject to special waste disposal.

Illus tration of the

K it

Part L is ting

The kit R 9841160 contains the following parts:

P art Number Description Quantity Indication

R 817483 FR MC G 5S LM S HT R 1

R 5976306 MAN INS G5S LMX LIG HT-S HTR 1

BARCO  7  Projection Systems

Removing the Electronic Box

What has to be

done

The Electronic Box can be slid out of the projector frame after 4 spring screws have

been loosened.

Necessary Tools A flatblade screwdriver of 5 mm

Removing the

Electronic Box

To remove the Electronic Box, follow the next procedure:

1

2

1

2

loosen the 4 spring screw (A).

Pull by the handles the Electronic Box out the projector

frame.

Step Action Image

Illustrations

A

Image 1

Image 2

BAR CO ——————————————————— 8 ————————————— Projection S ystems

R emoving the Lamp Unit cover.

What has to be

done

To be able to remove the top cover, the Lamp Unit C over has to be removed

beforehand.

Neces s ary Tools A flatblade screwdriver of 5 mm

R emoving the

s ide panel

To remove the side panel, follow the next procedure:

1

2

1

2

Turn with a screwdriver the side panel lock screw a quarter

turn counter clockwise.

Pull the right side of the panel towards you and further to

the right to remove.

Step Action Image

Illus trations

Image 1

Image 2

BAR CO ——————————————————— 9 ————————————— Projection S ystems

R emoval of the B ack Cover

What has to be

done

To remove the back cover, 3 Quarter turn fasteners have to be loosened.

Neces s ary Tools A flatblade screwdriver of 5 mm

R emoving the

back cover

To remove the back cover, follow the next procedure:

1

2

1

2

Turn with a screwdriver the 3 back cover lock screws (A) a

quarter turn counter clockwise.

S lide the back cover backwards to remove.

Step Action Image

Illus trations

A

Image 1

Image 2

BAR CO ——————————————————— 10 ————————————— P rojection S ystems

R emoval of the Top C over

What has to be

done

To remove the Top cover, remove first the 3 feet, next unfasten the light cover cloth and

finally loosen the 4 Quarter turn fasteners.

Neces s ary Tools A flatblade screwdriver of 5 mm and a Hexagon ball diver of 8mm

R emoving Top

cover

To remove the top cover, follow the next procedure:

1

2

1&2

3&4

R emove the 3 feet, using the hexagon ball driver.

Pull out the 5 push fasteners (A) holding the light cover

cloth to the lens frame.

Step Action Image

Illus trations

A

Image 1

Image 2

Image 3

Image 4

To be continued on next page

BAR CO ——————————————————— 11 ————————————— P rojection S ystems

R emoval of the Top C over (C ontinued)

R emoving Top

cover

To remove the top cover, follow the next procedure:

1

2

1,2&3

4

Turn with a Flatblade screwdriver the 4 Top cover lock

screws (A) a quarter turn counter clockwise.

Lift up the top cover to remove.

Step Action Image

Illus trations

Image 1

Image 2

Image 3

A

Image 4

BAR CO ——————————————————— 12 ————————————— P rojection S ystems

Ins talling the L ight S hutter As s embly

What has to be

done

The Light S hutter Assembly has to be placed onto the DMD engine frame and secured

with 2 screws.

Neces s ary Tools A flatblade screwdriver of 5 mm

to be continued on next page

Mounting the

L ight S hutter

To mount the Light S hutter Assembly, follow the next procedure:

1

2

1

Place the light S hutter unit on the front side of the DMD

frame.

Fix the light shutter unit on the DMD frame with the 2

provided screws.

Step Action Image

Illus trations

Image 1

BAR CO ——————————————————— 13 ————————————— P rojection S ystems

E lectrical C onnection of the Light S hutter

What has to be

done

Connect the Shutter Cable to the connector of the pre-installed cable.

Pre-ins talled C able A cable is already installed to allow an easy Shutter installation, this cable is connected

to connector J28 (image 1) on the Temp & Motor Control module and is guided through

theprovided hole in the Electronic B ox housing towards the shutter location located

near the engine (image 2 + image 3).

Note: On some older projectors, it is possible that this cable is not present, contact

Barco and order this cable, ordernumber: Z34870440, and install as described

above.

Connect the Shutter Cable to the connector on the pre-

installed cable.

Step Action Image

3

C onnection of the

L ight S hutter

To connect the Light Shutter , follow the next procedure:

Image 2Image 1

Image 3

1

J 28

BAR CO ——————————————————— 14 ————————————— P rojection S ystems

Operating the Light S hutter

Paus e key Pres s the paus e key on the R CU to activate/des activate the light s hutter.

BAR CO ——————————————————— 15 ————————————— P rojection S ystems

R eins talling the Top Cover

What has to be

done

R emounting the Top cover implies mounting the top cover, inserting the 3 feet and

finally fastening the light cover cloth.

Neces s ary Tools A flatblade screwdriver of 5 mm and a Hexagon ball diver of 8mm

Mounting the Top

cover

To mount the the top cover, follow the next procedure:

1

2

3

-

1,2&3

Loosen the securing screws of the E lectronic box and slide

the unit a little out of frame to allow securing the front

fastener studs (see page 8).

Place the top cover on its place, lining up the quarter turn

fasteners studs with their respective receptacle.

Turn with a Flatblade screwdriver the 4 fastener studs (A) a

quarter turn clockwise.

Step Action Image

To be continued on next page

Illus trations

Image 1

Image 2

Image 3

A

BAR CO ——————————————————— 16 ————————————— P rojection S ystems

R eins talling the Top C over (C ontinued)

Mounting the Top

cover

To mount the the top cover, follow the next procedure:

3

4

4&5

6&7

Insert the 3 feet (B) and tighten the included hexagon

socket head cap screw, using a hexagon ball driver.

Attach the light cover cloth to the lens frame by inserting

the 5 push fasteners (C ) .

Step Action Image

Illus trations

C

Image 4

Image 5

Image 6

Image 7

B

BAR CO ——————————————————— 17 ————————————— P rojection S ystems

R eins talling the B ack C over

What has to be

done

The back cover has to be slid over the rear of the projector and secured with 3 Quarter

turn fasteners.

Neces s ary Tools A flatblade screwdriver of 5 mm

reins talling the

back cover

To reinstall the back cover, follow the next procedure:

1

2

1

2

S lide the back cover over the rear of the projector.

Turn with a screwdriver the 3 Quarter turn fasteners (A) a

quarter turn clockwise.

Step Action Image

Illus trations

A

Image 1

Image 2

BAR CO ——————————————————— 18 ————————————— P rojection S ystems

R eins talling the Lamp Unit Cover

What has to be

done

The Lamp Unit C over has to be remounted.

Neces s ary Tools A flatblade screwdriver of 5 mm

R eins talling the

s ide panel

To reinstall the side panel, follow the next procedure:

1

2

1&2

2

Move the cover guides under the back cover and push the

front of the cover against the projector frame lining up the

cover lock screw with the speed nut (A) on the frame.

Turn with a screwdriver the side panel Quarter turn fas-

tener (B ) a quarter turn clockwise to lock.

Step Action Image

Illus trations

Image 3

Image 2

Image 1

A

B

BAR CO ——————————————————— 19 ————————————— P rojection S ystems

R eins talling the E lectronic B ox

What has to be

done

The E lectronic Box has to be reinstalled into the projector frame.

Neces s ary Tools A flat blade screwdriver of 5 mm

R eins talling the

E lectronic B ox

To reinstall the E lectronic Box, follow the next procedure:

1

2

1&2

3

Match the module box guides with the projector frame slots

and push the box to the end until the box fits.

S ecure the box with the 3 spring screws (A)

Step Action Image

Illus trations

Image 1

Image 2

A

Image 3

Barco Light Shutter for SLM Series Installation guide

Barco Light Shutter for SLM Series Installation guide

Related papers

Other documents