BARCO PROJECTION SYSTEMS
Date:10.05.2001
INSTALLATION MANUAL
Kit lamp for SLM projector
R9840740
Art. No.: R5976247Rev: 00
Lamp 1200W
Kit
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, May 2001.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO n.v./Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : +32/56/368211
Fax : +32/56/351651
E-mail : [email protected]
Visite Barco at the web : http://www.barco.com
Printed in Belgium
Contents
Safety ................................................................................... 4
Who ................................................................................................................................................................... 4
Hot Surface and Risk of Explosion. ................................................................................................................ 4
Risk of Electrical Shock................................................................................................................................... 4
Lamp Life Time Warning .................................................................................................................................. 4
Contents of the Kit .............................................................. 5
Lamp Type......................................................................................................................................................... 5
Warning !........................................................................................................................................................... 5
Lamp Disposal.................................................................................................................................................. 5
Part Listing ....................................................................................................................................................... 5
Illustration of the Kit ........................................................................................................................................ 5
Access to the Lamp Unit. ................................................... 6
What has to be done ........................................................................................................................................ 6
Necessary Tools ............................................................................................................................................... 6
Removing the side panel ................................................................................................................................. 6
Illustrations ....................................................................................................................................................... 6
Removing the Lamp Unit. ................................................... 7
What has to be done ........................................................................................................................................ 7
Necessary Tools ............................................................................................................................................... 7
Sliding out the lamp unit ................................................................................................................................. 7
Illustrations ....................................................................................................................................................... 7
Installation of the new the Lamp Unit................................ 8
What has to be done ........................................................................................................................................ 8
Necessary Tools ............................................................................................................................................... 8
Installing the lamp unit .................................................................................................................................... 8
Illustrations ....................................................................................................................................................... 8
Reinstalling the Side Panel. ............................................... 9
What has to be done ........................................................................................................................................ 9
Necessary Tools ............................................................................................................................................... 9
Reinstalling the side panel .............................................................................................................................. 9
Illustrations ....................................................................................................................................................... 9
BARCO 4 Projection Systems
Safety
Who This installation must be performed by authorized technical personnel* only.
General
CAUTION
Before attempting to remove any of the projectors covers, the
projector has to be turned off and disconnected from the wall
outlet to minimize the risk of electric shock.
Before starting with the Replacement of the Lamp Unit, always let
cool down the projector after operation in order to reduce the heat
on parts in the light path and to avoid burns.
WARNING
Eye damage may result from direct viewing the light produced by the lamp used in this
equipment. Always turn off lamp before opening cover.
PRODUCT CARE
Installation Kit: - The Kit R9840740 - Lamp 1200W - is designed for use ONLY with
the BARCO SLM series projectors.
Replacement parts - When replacement parts are required, be sure the service
technician has used original BARCO replacement parts or authorized replacement
parts which have the same characteristics as the BARCO original part.
Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
Under no circumstances are BARCO parts repairable by anyone other than BARCO.
* Authorized technical personnel: persons having appropriate technical training and
experience necessary to be aware of hazards to which they are exposed in performing
a task and of measures to minimize the danger to themselves or other persons.
BARCO 5 Projection Systems
Contents of the Kit
Lamp Type The kit contains a XENON 1200W projection Lamp mounted in a housing together with
the reflector.
Warning ! Never attempt to disassemble the lamp casing. Because of its high internal pressure,
there is a risk that this lamp will explode in either the hot or cold state. The specially
constructed lamp casing will retain the shards in the event of a lamp exploding.
Part Listing
The kit R9840740 contains the following parts:
Part Number Description Quantity Indication
R366243 NUT D985 M 5 STZN 3 C
R5976247 MAN INS G5SLM LMP 1
R763295 UN G10ELM LMP INFO 1 B
R816520 FRMC G5SLM L-SOURCE 1 A
Illustration of the
Kit
A
B
C
The 3 spacers with external thread are fixed to the lamp casing frame by a nut
M5 (to remove before inserting the lamp unit in the projector)
Lamp Disposal
To dispose of the units with defective or exhausted lamp, return the unit to BARCO in a
complete original packaging. This way is the kindest to the environment.
The lamps do not contain any materials which are harmful to the environment so they
are not subject to special waste disposal.
BARCO 6 Projection Systems
Access to the Lamp Unit.
What has to be
done
To access the lamp casing, a side panel has to be removed.
Necessary Tools A flatblade screwdriver of 5 mm
Removing the
side panel
To remove the side panel, follow the next procedure:
1
2
1
2
Turn with a screwdriver the side panel lock screw a quarter
turn counter clockwise.
Pull the right side of the panel towards you and further to
the right to remove.
Step Action Image
Illustrations
Image 1
Image 2
BARCO 7 Projection Systems
Removing the Lamp Unit.
What has to be
done
The lamp unit has to be slid out of the projector frame.
Necessary Tools Flatblade screwdriver of 5mm or Nutdriver of 8mm.
Sliding out the
lamp unit
To slide out the lamp unit out of projector frame, follow the next procedure:
1
2
1
1&2
Loosen the 3 spacer screws (A).
Using the provided handle (B), pull the lamp unit out of the
projector frame.
CAUTION: be careful not to drop the lamp unit (see safety
instructions in front of leaflet)
Step Action Image
Illustrations
B
A
image 1
image 2
BARCO 8 Projection Systems
Installation of the new the Lamp Unit.
What has to be
done
On the lamp unit the safety nuts have to be removed from the 3 spacer screws and
further the lamp unit has to be slid into the projector frame.
Necessary Tools Flatblade screwdriver of 5mm/Nut driver 8mm
Installing the
lamp unit
To install the lamp unitin the projector frame, follow the next procedure:
1
2
3
1
2&3
3
Remove the safety nut on the 3 spacer screws (A).
Line up the lamp unit guides with the guides on the projec-
tor frame (B) and push the unit into the frame until it fits.
Secure the position of the lamp unit with the 3 spacer
screws.
Step Action Image
Illustrations
image 1
image 3
B
C
image 2
A
BARCO 9 Projection Systems
Reinstalling the Side Panel.
What has to be
done
After the new lamp unit has been installed, the side panel has to be remounted.
Necessary Tools A flatblade screwdriver of 5 mm
Reinstalling the
side panel
To reinstall the side panel, follow the next procedure:
1
2
1&2
2
Move the cover guides under the back cover and push the
front of the cover against the projector frame lining up the
cover lock screw with the speed nut (A) on the frame.
Turn with a screwdriver the side panel lock screw (B) a
quarter turn clockwise to lock.
Step Action Image
Illustrations
Image 3
Image 2
Image 1
A
B
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Barco Refurb Xenon lamp for SLM G5/R6 series Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco 2 kW Xenon lamp SIM 10 Quick start guide
-
-
-
Barco Galaxy NW-7 EX Installation guide
-
-
-
-
-
-
Barco R9843115 User manual