Barco Refurb lamp for SLM Executive G10/R10 Installation guide
- Category
- Projectors
- Type
- Installation guide
This manual is also suitable for
Uni v ersal Lamp Replacement Kit
Installation manual
For SLM *8/*10 and R 9+/R12+ projectors
R9841810
R5976544/03
10/04/2005
Barco nv Events
Noordl
aan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail:
Visit us at the web: www.barco.com
PrintedinBelgium
1. Safety Warnings
1. SAFETY WARNINGS
1.1 Safety warnings during installation
Who may install
The installation must be performed by authorized technical personnel only.
Authorized technical personnel: persons having appropriate technical training and experience necessary to be aware of hazards to
which they are exposed in performing a task and of measures to minimize the danger to themselves or other persons.
Caution risk of electric shock
Before attempting to remove any of the projector’s covers, the projector has to be turned off a nd disconnected from the wall outlet
to minimize the risk of electric shock.
Cautiononhead
Before starting with the replacement of the lamp unit, always let cool down the projector after operation in order to reduce the heat
on parts in the light path and to avoid burns.
Warning eye damage
Eye damage may result from direct viewing the light produced by the lamp used in this equipment. Always turn off lamp before
opening cove r.
1.2 Product care
Installation Kit
The universal lamp replacement Kit R9841810 is designed for use ONLY with the BARCO SLM G8/R8, G10/R10, R9+ and R12+
series projectors.
The G8/R8 projectors need to have software version 1.17 in order for the universal lamps to work in them. If
not, when you install the lamp into the projector it tells you tha
t the lamp is incorrect
Replacement parts
When replacement parts are required , be sure the service
technician has used original Barco r eplacement parts or au thorized re-
placement parts which have the same characteristics as the Barco original part.
Unauthorized substitutions may r esult in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized
substitutions ma y void warranty.
Repairable
Under no circumstances a re Barco parts repairabl
e by anyone other than Barco.
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
1
1. Safety Warnings
2 R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
2. Introduction
2. INTRODUCTION
2.1 Content of the kit
Contentofthekit
The lamp kit consists in a lamp housing, Xenon lamp included. That means that the lamp position is factory ca librate d following th e
X- ,Y- and Z-axis. When observing a decrease in light output during the run time of the lamp, ONLY a realignment following the
Z-axis can solve the light output decrease.
B
A
Image 2-1
Spacers lock nut removal
Only for transport purposes, the 3 lamp housing fixation spacers (A) are fixed to the lamp casing frame by a
lock nut M5 (B). Always remove the lock nuts before inserting the lamp housing into the projector
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005 3
2. Introduction
4 R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
3. Removing the old lamp
3. REMOVING THE OLD LAMP
3.1 Access to the Lamp Unit.
What has to be done
To access the lamp casing, a side panel has to be removed.
Necessary tools
A flatblade screwdriver of 5 mm
Removingthesidepanel
1. Turn with a screwdrive r the side panel lock screw (A) a quarter turn counter clockwise.
A
Image 3-1
Unlocking the side cover
2. Pull the right side of the panel towards you and nex
t to the right to remove.
A
B
Image 3-2
Lamp cover removal
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005 5
3. Removing the old lamp
3.2 Removing the Lamp Unit.
What has to be done
The lamp unit has to be slid out of the projector frame.
Necessary tools
Flatblade screwdriver of 5mm or Nutdriver of 8mm.
Sliding out the lamp unit
1. Loosen the 3 spacer screws (A) o n the lamp house.
A
B
A
A
Image 3-3
Loosening the spacer screws
2. Using the provided handle (B), pull the lamp unit out of the projector frame.
B
Image 3-4
Sliding out the lamp housing
Caution: Be careful not to drop the lamp unit (see safety instructions in fron t of instruction manual)
6
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
4. Inserting the new lamp Unit
4. INSERTING THE NEW LAMP UNIT
4.1 Installation of the new Lamp Unit.
What has to be done
First remove the lock nut on each spacer screw and next slide the lamp unit into the projector frame.
Necessary tools
Flatblade screwdriver of 5mm or Nut driver 8mm
Installing the lamp unit
1. Remove the lock nut (B) on the 3 spacer screws (A).
B
A
Image 4-1
2. Line up the lamp unit guides (A) with the guides on the projector base (B) and push the unit into the frame until it fits.
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
7
4. Inserting the new lamp Unit
B
A
Image 4-2
Lamp unit mounting
3. Secure the position of the lamp unit with the 3 spacer screws.
A
A
A
Image 4-3
Lamp unit fixation
4.2 Optical Alignment of the lamp
What may be adjusted!!
The adjustments to the Y-axis and X-axis (balancing the light intensity) are FACTORY PREADJUSTED. Consequently, both ad-
justable screws are ancho
red by a lock screw and sealed with a warranty label (Destroying the label void the warranty).
ONLY the Optical readjustment to the Z-axis may be done an d is recommended a fter the lamp has operated for m any run times. An
optical realignment of the lamp to the z-axis could compen sate the decrease in light output.
8
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
4. Inserting the new lamp Unit
X
Z
Y
Factory Preadjusted
Image 4-4
Optical alignm ents scews
Necessary tools
•AllenKey3mm
• nut driver 10mm
How to adjust
Optical alignment of the lamp t o the z-axis, follow the next procedure:
1. Put a lightmeter in the center of the screen.
2. Enter the ‘RANDOM ACCESS ADJUSTMENT M OD E’, select consecu tively ‘Picture Tuning’ and ‘Colour Temperature ’. Finally
set C olour Temperature on ‘PROJECTOR W HIT E’.
3. Enter the ‘INSTALLATION MODE’ and select ‘Internal Patt erns’. Fina
lly s et Internal pat terns on ‘PURITY’.
4. Enter the ‘SERVICE MODE’ and select ‘Add-Ins’. F inally set CLO on ‘INACTIVE’.
5. Loosen the lock nut (A), securing the adjustable screw (B) for the opt ical Z -axis adjustment.
A
B
Image 4-5
Optical alignment Z-axis
6. Carefully adjust the adjustable screw (B), using an Allen key of 3mm, for m aximum light fall on the screen.
7. Lock the adjustable screw by fastening the lock nut (A).
8. Cancel the above modified projector settings (Step 2 to 4).
R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
9
4. Inserting the new lamp Unit
4.3 Reinstalling the Side Panel
What has to be done
After the new lamp unit has been installed, the side panel has to b e remounted.
Necessary tools
A flatblade screwdriver of 5 mm
Reinstalling the side panel
1. Move the cover guides under the back cover and push the front of the cover against the projector frame lining up the cover lock
screw with the speed nut (A) on the frame.
Image 4-6
Mounting the side cover
Image 4-7
Closing the side cover
2. Turn with a screwdriver the side panel lock screw (B) a quarter turn c lockwise to lock.
B
Image 4-8
Locking side panel
10 R5976544 UNIVERSAL LAMP REPLACEMENT KIT 10/04/2005
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Barco Refurb lamp for SLM Executive G10/R10 Installation guide
- Category
- Projectors
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco Spare lamp for XLM H25 Installation guide
-
-
-
-
Barco Galaxy NW-7 EX Installation guide
-
-
Barco Galaxy NW-12 EX Installation guide
-
-
-