Johnson Controls OpenBlue Industrial Refrigeration User guide

Johnson Controls
Brand
Johnson Controls
Model
OpenBlue Industrial Refrigeration
Type
User guide
LIT-12014057
Digital Solutions
www.johnsoncontrols.com
2022-07-15
OpenBlue Industrial Refrigeration
Configuration Guide
2 OpenBlue Industrial Refrigeration Configuration Guide
Contents
ContentsOverview............................................................................................................................................................5
Connected IREF module.................................................................................................................................. 5
Portfolio.................................................................................................................................................. 5
Region..................................................................................................................................................... 6
Branch..................................................................................................................................................... 7
Customer................................................................................................................................................ 7
Site........................................................................................................................................................... 8
Plant room.............................................................................................................................................. 9
Additional Connected IREF module actions..................................................................................... 10
Equipment Configuration module............................................................................................................... 10
Create Equipment................................................................................................................................11
Equipment Template Creation........................................................................................................... 12
Map Equipment Points........................................................................................................................13
Configuring and mapping points.............................................................................................................14
Creating virtual points...............................................................................................................................15
Site Level Dashboard...........................................................................................................................16
Equipment Relationship......................................................................................................................18
Mapped Points module................................................................................................................................. 19
Viewing raw data................................................................................................................................. 19
Meter Configuration module........................................................................................................................20
Creating a meter..................................................................................................................................21
Creating a sub-meter.......................................................................................................................... 22
Global Rules module......................................................................................................................................22
Threshold..............................................................................................................................................22
Assigning threshold values to constant templates................................................................................23
Assigning thresholds to multiple constant templates...........................................................................23
Equipment fault rules..........................................................................................................................24
Mapping a fault rule to equipment..........................................................................................................24
Muted Faults in Global Rules..............................................................................................................25
Unmuting faults in Global Rules...............................................................................................................25
Custom Rules module....................................................................................................................................26
Constant template...............................................................................................................................26
Creating a constant template...................................................................................................................26
Sub-rules...............................................................................................................................................27
Creating a sub-rule.................................................................................................................................... 27
Modifying or deleting a sub-rule..............................................................................................................28
Equipment fault rules..........................................................................................................................28
Creating a fault rule................................................................................................................................... 28
Modifying or deleting a fault rule............................................................................................................ 30
Mapping equipment to a fault rule..........................................................................................................30
Mapping a diagnostic rule to a main fault rule...................................................................................... 31
OpenBlue Industrial Refrigeration Configuration Guide 3
Threshold..............................................................................................................................................32
Assigning threshold values to constant templates................................................................................32
Assigning thresholds to multiple constant templates...........................................................................32
Diagnostics........................................................................................................................................... 33
Creating diagnostic criteria.......................................................................................................................33
Modifying or deleting a diagnostic rule.................................................................................................. 34
Mapping a reason to a diagnostic rule....................................................................................................34
Reason...................................................................................................................................................35
Creating a reason.......................................................................................................................................35
Muted Faults in Custom Rules........................................................................................................... 36
Unmuting faults in Custom Rules............................................................................................................ 36
Global Points module.....................................................................................................................................37
Creating a global point....................................................................................................................... 37
Users module..................................................................................................................................................38
Create Role........................................................................................................................................... 38
Creating roles............................................................................................................................................. 38
Role & Rights........................................................................................................................................ 39
Assigning permissions to roles................................................................................................................ 39
Active User List.....................................................................................................................................40
Creating a user account............................................................................................................................ 40
Unlock User.......................................................................................................................................... 41
Product warranty............................................................................................................................................42
Software terms............................................................................................................................................... 42
Contact information.......................................................................................................................................42
OpenBlue Industrial Refrigeration Configuration Guide4
Overview
The OpenBlue Connected Industrial Refrigeration (OBIR) application is based on the OBEM
platform, which gives insights into equipment performance with various widgets, graphics and
gives ability to generate reports that can be shared with internal service team and customers.
You can also generate equipment fault rules to diagnose known issues that can occur with an
equipment.
When you log in to the application, in the OBEM menu tray, OBIR is available as an app that the
user can access to navigate to the OBIR application. When you navigate to the OBIR application,
the world map is the landing page. From this page, you can navigate to the Asset Manager module,
Reports module, and Setup module.
This document contains information about the configuration of the OBIR application. The Setup
page contains a series of modules at the top of the page. Navigate to each module and complete
the configuration to see data on OBIR dashboards.
Connected IREF module
The Connected Industrial Refrigeration Tree is a hierarchical list of all the physical locations that
you want to include in the OpenBlue Connected Industrial Refrigeration application. When you
configure your tree, you assign equipment and data points to your spaces. The relationships
between spaces, data points, and equipment form the basis for equipment analysis on the OBIR
dashboards.
Configure your tree according to the following six levels:
•Portfolio
•Region
•Branch
•Customer
•Site
•Plant room
Portfolio
Portfolio is the highest-level space and contains multiple customers in multiple regions. Portfolio
creation is a one-time activity completed from the back end. You cannot modify any details in the
portfolio section.
5OpenBlue Industrial Refrigeration Configuration Guide
Region
You can add region details that represent your region under the OBIR portfolio. For example, you
add the United States.
About this task:
Complete the following steps to add a region:
1. On the Setup page, click the Connected IREF module.
2. Click Portfolio to enable the Add icon. Click this icon to add the region details.
3. In the Region Name field, enter the name of your region. Region names can contain a
maximum of 100 characters.
4. Click Save to add the region details.
5. If you create or have access to multiple regions, use Region Order to change the region
order.
Region appears on the left navigation tree under portfolio in the Asset Managerand Reports
modules.
OpenBlue Industrial Refrigeration Configuration Guide6
Branch
Add branch details that represent your branch under the OBIR region.
About this task:
Complete the following steps to add a branch:
1. On the Setup page, click the Connected IREF module.
2. Click on a region to enable the Add icon. Click this icon to add the branch details.
3. In the Branch Name field, enter the name of your branch. Branch names can contain a
maximum of 100 characters.
4. The new branch displays the name of the region in the Region Name field.
5. In the Address 1 and optional Address 2 fields, enter the address of your branch. Addresses
can contain a maximum of 100 characters.
6. Optional: In the City field, enter the name of the city. City names can contain a maximum of
50 characters.
7. From the Country list, select the country name.
8. Optional: In the Zip code field, enter the zip code of the branch. Zip codes can contain a
maximum of 50 characters.
9. Optional: In the Latitude field, enter the latitude of the branch. Latitudes can contain a
maximum of 6 decimal values.
10. Optional: In the Longitude field, enter the longitude of the branch. Longitudes can contain a
maximum of 6 decimal values.
11. Click Save to add the branch details.
12. If you create or have access to multiple branches, you can change the branch order under
specific region by using Branch Order.
Branch appears on the left navigation tree under the selected region in the Asset Manager
and Reports modules.
Customer
Add customer details that represent your customer under the OBIR branch.
About this task:
7OpenBlue Industrial Refrigeration Configuration Guide
Complete the following steps to add a customer:
1. On the Setup page, click the Connected IREF module.
2. Click the branch to enable the Add icon. Click this icon to add the customer details.
3. From the Customer Name list, select the name of the customer.
4. In the Customer ID field, enter the customer ID. A customer ID can contain a maximum of 50
characters.
5. In the Customer Logofield, upload the logo of the customer. You can upload a customer logo
in JPG, JPEG, or PNG formats. The image is automatically resized to 200 x 200 pixels.
6. If you have access to multiple customers, use Customer Order to change the customer order
under a specific branch.
The customer appears on the left navigation tree under selected branch in the Asset Man-
agerand Reports modules.
Note: The customer is onboarded through a super admin user, which is then available in
the Customer list. For more information on users and access levels, refer to the attached
Excel document Roles and Access applicable for OBIR.
Site
Add site details that represent your site under OBIR customer.
About this task:
Complete the following steps to add a site:
1. On the Setup page, click the Connected IREF module.
2. Click on the customer to enable the Add icon. Click this icon to add the site details.
3. In Site Name field, enter the name of your site. Site names can contain a maximum of 32
characters.
4. From the Site Type list, select the site type value.
5. In the Address 1 and optional Address 2 fields, enter the address of your site. Addresses can
contain a maximum of 100 characters.
6. Optional: In the City, State field, enter the name of the site's city and state. This field can
contain a maximum of 50 characters.
7. From the Country list, select the country name.
OpenBlue Industrial Refrigeration Configuration Guide8
8. Optional: In the Zipcode field, enter the zip code of the branch. Zip codes can contain a
maximum of 50 characters.
9. In the Latitude field, enter the latitude of the branch. Latitudes can contain a maximum of 6
decimal values.
10. In the Longitude field, enter the longitude of the branch. Longitudes can contain a maximum
of 6 decimal values.
11. In the Site Total Area (sq. ft.) field, enter the total area of site in square feet. You can add a
maximum of 15 numbers.
12. From Site Status list, select the status of the site as Active or Inactive.
13. Optional: In the Upload Image field, upload the image of site. You can upload a site image in
JPG, JPEG, or PNG formats.
14. In the Start Date field, select the site start date based on the service contract.
15. In the End Date field, select the site end date based on the service contract.
16. From the Refrigerant list, select the refrigerants used in the site.
17. From the Network Distribution list, select the network distributions of your site.
18. From the Architecture list, select the site architecture.
19. Optional: From the Secondary Coolant list, select the secondary coolant used in the site.
20. In the Demand Rangefield, enter the minimum and maximum values for the demand to
display on the site dashboard. You can only enter numbers in the Min and Maxfields.
21. Click Save to add the site details.
22. If you have access to multiple sites, use Site Order to change the site order under a specific
customer.
The site displays on the world map and on the left navigation tree under the selected cus-
tomer in the Asset Manager and Reportsmodules.
Plant room
Add plant room details that represent your plant room under OBIR site. For example, you add
Engine Room.
About this task:
9OpenBlue Industrial Refrigeration Configuration Guide
Complete the following steps to add the Plant Room:
1. On the Setup page, click the Connected IREF module.
2. Click on the site to enable the following Plant Room icon:
Click this icon to add plant room details.
3. In the Plant Room Name field, enter the name of the plant room. The plant room name can
contain a maximum of 32 characters.
4. Optional: In the Description field, add the description related to plant room. The description
can contain a maximum of 50 characters.
The Plant roomdisplays on the left navigation tree under the selected site in the Asset Man-
ager and Reports modules.
Additional Connected IREF module actions
• To modify any details, click the relevant hierarchy, update the details, then click Save.
• To delete a level under Portfolio, use the Delete icon if you have CRUD operation access. If a
parent level contains a child level, delete the child level first, and then delete the parent level.
Note: You cannot delete a plant room with associated equipment or meters, and you
cannot delete a site with associated plant rooms, equipment, or meters.
• When you complete the Connected Industrial Configuration Tree configuration, you
can create equipment and meters, assign data points, and configure the fault rules. OBIR
dashboards use the Connected IREF tree configuration to analyze the equipment performance.
Equipment Configuration module
The Equipment Configuration module creates entries that represent the equipment in the site
and identify trends, faults, issues, and find opportunities for operational improvements and cost
reduction.
OpenBlue Industrial Refrigeration Configuration Guide10
Use the Equipment configuration section to map the data points from OBB to the equipment
and site-level dashboard cards, and to create custom equipment templates. When you create the
equipment and map data points to the equipment, you can use the equipment dashboards to
analyze the equipment's performance and to identify areas for operational optimization.
The Equipment configuration module contains the following tabs:
•Create Equipment
•Equipment Template Creation
•Map Equipment Points
•Site Level Dashboard
•Equipment Relationship
Create Equipment
Use the Create Equipment tab to create equipment entries for your site.
About this task:
To create an equipment entry, complete the following steps:
1. On the Setup page, navigate to the Equipment Configuration module, and click the Create
Equipment tab.
2. From the Region list, select the region where you want to create an equipment entry.
3. From the Branch list, select the branch.
4. From the Customer list, select the customer that you want to create an equipment entry for.
5. From the Site list, select the site.
6. Optional: From the Plant Room list, select the plant room where you want to create the
equipment.
Note: The System is IREF by default.
7. From the Equipment Category list, select the equipment category. For more information,
refer to the attached Excel document OBIR_Equipment List.
8. From the Equipment Typelist, select the type of equipment you want to create. For more
information, refer to the attached Excel document OBIR_Equipment List.
9. From the Fault Detection list, select if you want to enable fault detection for this equipment
on the dashboard. If you do not enable fault detection, the equipment does not register
faults in the OBIR application.
10. In the Equipment Name field, enter the name of the equipment. Equipment names can
contain a maximum of 32 characters and should be unique under the selected site.
11. Optional: In the Max Power (kW) field, enter the maximum power of the equipment.
12. Optional: In the Suffix field, enter comma-separated values to add multiple equipment items
of the same category and same type. For example, if 10 items of equipment of the same
category and type are to be added, then enter the specific name in the Equipment Name
field and enter 10 comma-delimited numbers in the Suffix field so that the 10 items can be
added at the same time.
13. Optional: From the Meters list, select the meters that you want to associate with your new
equipment. If you do not assign an Equipment category to your meters in the Meters section
of the Setup page, you cannot add meters to the equipment. For more information, see Meter
Configuration module.
14. Optional: In the Installation Date, add the date of equipment installation.
11OpenBlue Industrial Refrigeration Configuration Guide
15. Optional: Click Equipment Specification to add the Key Performance Indicator (KPI) values
and the units.
- From the Equipment Specification window, click Save.
16. To save the new equipment, click Add. You can view the new equipment in the grid below.
17. To update the equipment details, select the equipment entry from grid and modify the details
then click Update.
18. To delete the equipment, select the equipment entry from grid and click Delete.
19. Use Clear to reset the fields.
When you add equipment, it is displayed in grid below. If you want to delete or modify any
equipment, select the equipment from grid and click Delete or update the details and click
Update.
When you complete the equipment creation, you can map the data points to equipment that
gathers live data from OpenBlue Bridge. For more information on data point mapping, see
the Map Equipment Points section.
Equipment Template Creation
Use the Equipment Template Creation tab to add the templates which are not listed in the default
template list. Equipment templates are based on customer and equipment type. Templates added
under a customer are available in all of the same types of equipment in all sites of the selected
customer.
About this task:
To create an equipment template, complete the following steps:
1. On the Setup page, navigate to the Equipment Configuration module, and click the
Equipment Template Creation tab.
2. From the Region list, select the region where you want to create an equipment template.
3. From the Branch list, select the branch.
4. From the Customer list, select the customer that you want to create an equipment template
for.
OpenBlue Industrial Refrigeration Configuration Guide12
5. From the Equipment Category list, select the category of equipment for which you want
to as equipment template. For more information, refer to the attached Excel document
OBIR_Equipment List.
6. From the Equipment Typelist, select the type of equipment for which you want to
as equipment template. For more information, refer to the attached Excel document
OBIR_Equipment List.
7. From Unit Type list, select the unit type for the template.
8. In the Enter Template Name field, enter the name of an equipment template you want to
add. Only alphanumeric values and the _ and – symbols are allowed in the Template Name
field.
9. Optional. From the Equipment Dashboard Selection list, select the equipment level widget
name. Select Trend if you want to display the data of point mapped to the newly created
equipment template in Trend widget at equipment level.
10. To save the details click Add. You can view the newly created equipment template in the grid.
When you add an equipment template, it displays in the grid. If you want to modify any tem-
plate, click Edit from the grid, modify the details and click Update.
When you complete the creation of equipment template, you can map the data points to tem-
plates. For more information on data point mapping, see the Map Equipment Points section.
Map Equipment Points
Use the Map Equipment Points tab to associate data points that you input when you configure
OpenBlue Bridge with equipment that you create. Each type of equipment has inbuilt or predefined
templates that represents the core data point list for that equipment type. You need to assign the
points configured in OpenBlue Bridge to the equivalent template available in the OBIR application.
If you want to add a new template that is not already listed in the default template list, then you
can use the Equipment Template Creation tab. For more information about equipment template
creation, see Equipment Template Creation.
When you assign data points to specific equipment templates, you establish the relationship
between information coming from physical data points with the representation of the equipment
in the OBIR application. If you do not assign all relevant data points to equipment templates, the
dashboards do not display the data.
13OpenBlue Industrial Refrigeration Configuration Guide
Configuring and mapping points
About this task:
To configure and map data points with equipment, complete the following steps:
1. On the Setup page, click the Equipment Configuration module and then click the Map
Equipment Points tab.
2. From the Region list, select the region where you have created equipment and want to map
data points.
3. From the Branch list, select the branch where you have created equipment and want to map
data points.
4. From the Customer list, select the customer configured for OpenBlue Bridge and created
equipment, that you want to map data points.
5. From the Site list, select the site where you have created equipment and want to map data
points. After you select the site, the OpenBlue Bridge configured for the selected customer
and equipment created under the selected site displays.
6. From the Points Tree section, click the Select OBB list and select the configured OpenBlue
Bridge device. After you select the OpenBlue Bridge device, clicking Resend Discovery
enables you to view the data source, devices, and points list.
7. From the Select Data Source list, select the data source that contains the points you want to
use.
8. From the Select Device list, select the device that corresponds with the data point that you
want to map. You can use All Meters, All Points, Unmapped Point, and Units to filter the
point list. To further filter results, you can use the search field.
9. From the Points Tree, if the data point name has red text, update the information relating to
the data point. To configure the data point or update the information, complete the following
steps:
a. Double-click on Point, and the Point Configuration window opens. The FQR/Point path
displays the path of the selected point.
b. The Name field displays the name of the point added during OpenBlue Bridge
configuration. You can update the name from the Point Configuration window.
c. From the Read Frequency list, select the read frequency of the point.
OpenBlue Industrial Refrigeration Configuration Guide14
Note: This is not applicable for points coming from OpenBlue Bridge in this OBIR
release.
d. From the Unit Type list, select the unit type for the point.
e. From the Unit list, select the unit of the point.
f. From the Point Role list, select the point role for the point.
g. From the Series Type list, select the series type for the point.
h. In the Min Value field, add the minimum sensor value for the point.
i. In the Max Value field, add the maximum sensor value for the point.
j. If you select the Unit Type as Binary or Enum, then the Point State field is available to
add values for states to be displayed on dashboards and graphics.
k. Click Update to save the details, and the point color changes to green.
10. From the Equipment Template Tree, expand the equipment name under which you want to
map the point.
11. From the Point Tree, drag the configured point and drop it to the specific template in the
Equipment Template Tree. For more information about default equipment templates, refer
to the attached Excel document OBIR_Data_Point_List.
Note: The system does not allow you to drag a data point into the equipment template if
the data point is not in the same unit as the template. The data point must be measuring
in a similar unit to the template for it to be mapped. For example, a temperature point
should be mapped to a temperature template, such as Discharge Temperature. If a
data point is dragged to a template with a dissimilar unit, a red banner indicates that it
cannot be placed into the position.
Note: When the point is correctly mapped to an equipment template, the color of the
data point changes from green to blue. If it remains green, it indicates that the data
point is mapped incorrectly.
12. Click on the equipment name in the Equipment Template Tree to see the mapped points
and original template names associated with equipment. The Equipment Point mapping
pane displays on the right with a table of associated template names and points mapped to
those templates. Templates with no mapped points show an empty cell in the Mapped Points
column.
13. To unmap any mapped point, select the point mapped to the template from the Equipment
Template Tree. Click the enabled Delete button to unmap the point.
Creating virtual points
Virtual points can also be created in the Map Equipment Points tab.
About this task:
Complete the following steps to create virtual point:
1. Click the equipment name from the Equipment Template Tree to enable the Add icon.
2. Click the Add icon to open the Virtual Points Details pane on the right side.
3. In Point Name field, enter the name of the virtual point.
4. Optional: In the Description field, enter the description for the point.
5. From the Unit Type list, select the unit type for point.
6. From the Unit list, select the unit of the point.
7. From the Point Role list, select the point role for the point.
8. From the Series Type list, select the series type for the point.
15OpenBlue Industrial Refrigeration Configuration Guide
9. Click Virtual Point Definition to open the window.
10. Create an equation you want to have for the virtual point. Drag and drop points from the left
side trees
Note: To use points in virtual point equations, you map the points to the equipment
template. If the point is not mapped to the template, then you cannot drag it in the
Virtual Point Definition window.
11. Click Validate Syntax and click Save to add the definition.
12. Click Save to add the virtual point. It is now available in the left-side Virtual Points section.
13. You can drag and drop the virtual points to map them to equipment templates.
14. If you want to update the virtual point, click on the virtual point's name from the Virtual
Points tree. The Virtual Point Details pane opens at the right, and you can update the
information.
After you complete the data point configuration and mapping, the application receives the
data and displays it on the equipment level dashboards. You can check the raw data for each
point mapped to equipment in the Mapped Points tab. For more information, see Mapped
Points module.
Site Level Dashboard
Use the Site Level Dashboard tab to map the data points to widgets displayed at site level in the
Asset Manager module. Site-level dashboard widgets are preconfigured, you need to assign the
points configured in OpenBlue Bridge to equivalent template available in OBIR application. When
you assign data points to specific templates of site level widgets, you establish the relationship
between information coming from physical data points with the representation of the widgets in
OBIR application. If you do not assign all relevant data points to widget templates, the site level
dashboards does not display the data.
About this task:
To map points in the site level dashboard widget, complete the following steps:
1. On the Setup page, navigate to the Equipment Configuration module and click the Site
Level Dashboard tab.
2. From the Region list, select the region where you have created the site.
3. From the Branch list, select the branch.
4. From the Customer list, select the customer that you have configured OpenBlue Bridge and
created the site for.
5. From the Site list, select the site which you have created and want to map data points to
widgets.
6. When you select the site, the OpenBlue Bridge configured for the selected customer and
widget list for selected site displays.
7. From the Points Tree section Select OBB list, select the OpenBlue Bridge which you have
configured.
Note: When you send the Resend Discovery command from Map Equipment Points
tab, discovered data source, device and point list displays in the Points Tree at Site Level
Dashboard tab.
8. From Select Data Source list, select the data source that contains the points you want to use.
9. From Select Device list, select the device that corresponds with the data point that you want
to map. You can use All Meters, All Points, Unmapped Point and Units to filter point list. To
further filter results, you can use the search field.
OpenBlue Industrial Refrigeration Configuration Guide16
10. From the Points Tree, if the data point name has red text, you update the information
relating to the data point. To configure data point or update the information, complete
following steps:
a. Double click on point, Point Configuration window opens.
b. FQR/Point path displays the path of the selected point.
c. The Name field displays the name of the point as per added during OpenBlue Bridge
configuration. You can update the name as well from Point Configuration.
d. From the Read Frequency list, select the read frequency of point.
Note: This won’t be applicable for points coming from OpenBlue Bridge in this
OBIR release.
e. From Unit Type list, select the unit type for point.
f. From Unit list, select the unit of the point.
g. From Point Role list, select the point role for the point.
h. From Series Type list, select the series type for the point.
i. In Min Value field, add the minimum sensor value for the point.
j. In Max Value field, add the maximum sensor value for the point.
k. If you have selected Unit Type as Binary or Enum, the Point State field is available
where you can add values for states which are displayed on dashboards and graphics.
l. Click Update to save the details, and the point color changes to green.
11. From the Dashboard Tree, expand the widget name under which you want to map the point.
12. From Point Tree, drag the configured point and drop it to the specific template in Dashboard
Tree.
Note: The system does not allow you to drag a data point into the template if the
data point is not in the same unit of measurement as the template. For example, a
temperature point must be mapped to a temperature template, such as Discharge
Temperature. If a data point is dragged to a template with a different unit of
measurement, a red banner indicates that it cannot be placed into the position.
Note: When the point is correctly mapped to a widget template, the color of the data
point changes from green to blue. If it remains green, it indicates that the data point is
mapped incorrectly.
13. To unmap any mapped point, select the point mapped to the template from the Dashboard
Tree and the Delete button enables. Click Delete to unmap the point.
14. Click Unmapped Template if you want to view the list of templates to which no data point is
mapped.
15. Virtual points created at Map Equipment Points tab are displayed in the left side Virtual
Points tree at Site Level Dashboard tab for the selected site. You can drag and drop the
virtual points to map them to site level widget templates. For more information on creating
virtual points, refer to the Map Equipment Points section.
When you complete the data point configuration and mapping to widget templates, data
starts flowing into the application and it displays on the site level dashboards. You can check
the raw data for each point mapped to site level dashboards in the Mapped Points tab. For
more information, refer to the Mapped Points module section.
17OpenBlue Industrial Refrigeration Configuration Guide
Equipment Relationship
Use the Equipment relationship tab to create parent-child relationships between equipment.
For example, if you have equipment that powers or serves other types of equipment, you can
declare that relationship in this tab. If the parent equipment has a fault, it may or may not cause an
associated fault on the child equipment. Additionally, child equipment may have their own faults.
About this task:
To create relationships between equipment, complete the following steps:
1. On the Setup page, navigate to the Equipment Configuration section and click the
Equipment Relationship tab.
2. From the Region list, select the region where you have created an equipment entry and want
to configure the equipment relationship.
3. From the Branch list, select the branch where you want to create the equipment relationship.
4. From the Customer list, select the customer that you want to create an equipment
relationship for.
5. From the Site list, select the site where you have created an equipment entry and want to
configure the equipment relationship.
6. When you select the site, equipments created under the site display.
7. From the Serving Equipment list on the left, expand the equipment types, and select the
check box next to each equipment name that you want to build a child relationship with. This
is your parent equipment.
8. From the Served Equipment list on the right, expand the equipment type that you want to
target, and select the equipment name to set as a child.
9. To create the relationship, click Sync.
You can view the parent-child relationship in the Equipment Relationship list.
If you want to delete any relationship, select the respective relationship and click Delete.
When any fault generates, the relationship displays on the dashboard.
OpenBlue Industrial Refrigeration Configuration Guide18
Mapped Points module
The Mapped Points module displays all the data points mapped under the selected site in the OBIR
application, including data points mapped to equipment, site level dashboard widgets, and meters.
You can view raw data coming into the OBIR application before any system processing occurs.
You can view this data over one week, one month, three months, six months, one-year, or custom
timeline. You can use this feature to troubleshoot any data points that do not perform correctly.
Viewing raw data
About this task:
To view raw data, complete the following steps:
1. On the Setup page, click the Mapped Points module to reach the All Points tab.
2. From the Region list, select the region where you have mapped the data points.
3. From the Branch list, select the branch.
4. From the Customer list, select the customer that you have mapped the data points for.
19OpenBlue Industrial Refrigeration Configuration Guide
5. From the Site list, select the site.
6. After you select the site, the Mapped Points table displays all of the data points mapped to
equipment, site level dashboards, and meters under the selected site.
7. The Point Name column displays the names of the data point.
8. The Point Path column displays the exact mapped path of the data point. This provides an
easy way to locate the data point.
9. The Source column displays the source type of the data point. For a data point located in a
meter, the Source column specifies whether it is an online or offline meter. For data points
located in equipment, the Source column specifies the equipment category. For example,
Screw Compressor.
10. The Unit of Measure column specifies the unit of the data point as it is configured in the
Point Configuration window.
11. From the Rollup Status column, click on the ^ icon to see if the data is aggregated to a
different level. For example, 15 mins, Hourly, Daily, Monthly and Yearly. You can also view the
last aggregated date and time and the value for all aggregation levels.
12. From the Points list, double-click on the name of the data point for which you want to see the
raw data.
13. A Raw Data window displays a graph of the raw data of selected data point.
14. In the upper-right section of the Raw Data window, select the time frame of the data that you
want.
15. You can select the Gridicon in the upper-right section of the Raw Data window to view the
data in grid format.
16. To export the raw data in a CSV or other file type, click the Settings icon on the upper-right
section of the Raw Data window, then click the Download icon. Select the file format that you
want.
17. Change the theme color of the Raw Data window using Theme Color option from Settings
icon.
Note: Raw data can be analyzed in this Mapped Points tab. You can check for the latest
aggregation level values to be displayed on the dashboards.
Meter Configuration module
Use the Meter Configuration section of the Setup page to create meters, define the relationship
between meters and spaces, and assign data points to meters.
OpenBlue Industrial Refrigeration Configuration Guide20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Johnson Controls OpenBlue Industrial Refrigeration User guide

Johnson Controls
Brand
Johnson Controls
Model
OpenBlue Industrial Refrigeration
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents