Xerox 230 LP, your new printer, offers a range of capabilities to enhance your printing experience. With its advanced features, you can effortlessly print high-quality documents, take advantage of network connectivity options, and customize your printing settings to meet your specific needs. From crisp text to vibrant graphics, the Xerox 230 LP delivers professional-looking results every time you print.
Xerox 230 LP, your new printer, offers a range of capabilities to enhance your printing experience. With its advanced features, you can effortlessly print high-quality documents, take advantage of network connectivity options, and customize your printing settings to meet your specific needs. From crisp text to vibrant graphics, the Xerox 230 LP delivers professional-looking results every time you print.
7+('2&80(17&203$1<
DC230LP Windows NT
®
4.0 NetBIOS/IP Quick Install
Page 1 of 4
This installation procedure assumes that you
know how to navigate through the menu system
on the DC230LP Control Panel. Refer to the
quick reference card,
Using the Menu System,
(701P96834) for assistance.
1. Connect the DC230LP to your network
outlet or cable.
2. Access the System Administration menus:
a)
Press [Online] to take the printer off
line. displays.
b)
Press [Menu]. displays.
c)
Press [], then press [] or [] until
displays.
d)
Press []. displays.
e)
Use the [] and [] keys to enter
[2222].
Note: 2222 is the factory default password and
may be changed to suit your needs. Refer to the
DC230LP System Administration Guide,
Network Installation and Troubleshooting
.
f)
Press [Enter].
displays.
Printer Off Line
Main Menu
>
System
Administration
>
Enter Password
>
System Admin
>
3. Access the TCP/IP menus:
a)
Press []. displays.
b)
Press [] until
displays.
c)
Press []. displays.
d)
Press []. displays.
Note: If TCP/IP has been installed on the
DC230LP, go to step 10. If TCP/IP has not been
installed, continue with step 4.
4. Set the IP Address (skip this step if using
RARP):
a)
Press []. displays.
Note: Use zeros to supplement each address
segment if fewer than 3 digits are used; e.g.,
13.252.25.08 = 013.252.025.008.
Port Setup
>
Network Setup
>
TCP/IP
>
IP Address
(current entry)
>
IP Address =
(current entry) *
Over
Installation Requirements:
To install the DC230LP in a DHCP environment,
exclude the addresses assigned to the
DC230LP at the DHCP server.
Before Installation:
Record the following information for use during
setup at the DC230LP.
TCP/IP:
TCP/IP Address:________________________
Gateway Address: ______________________
Subnet Mask: __________________________
Broadcast Address: _____________________
Host Name:____________________________
NetBIOS:
Host Name:____________________________
Printer Name: __________________________
Workgroup:____________________________
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
7+('2&80(17&203$1<
DC230LP Windows NT
®
4.0 NetBIOS/IP Quick Install
Page 2 of 4
7. Enter the Subnet Mask:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Use the [] or [] key to select the
first digit of the Subnet Mask for your
network.
d)
Press [] to move to the next digit.
Repeat this procedure to enter the
entire Subnet Mask.
e)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
8. Enter the Broadcast Address:
Note: Broadcast Address is where all the host
bits are set to either zeros (0) or ones (1).
a)
Press [] until
displays.
b)
Press []. displays.
Subnet Mask
(current entry)
>
Subnet Mask =
(current entry)
Subnet Mask
(your entry)
>
Broadcast Addr
(current entry)
>
Broadcast Addr =
(current entry)
b)
Use the [] or [] key to enter the
first digit of the IP Address.
c)
Press [] to move to the next digit.
Repeat this procedure to enter the
entire IP Address.
d)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
5. RARP Setup:
Note: If you used a static IP Address, leave the
RARP setting at
Disabled
.
a)
To change the RARP setting, press
[] until the current setting displays
.
b)
Press []. displays.
c)
Press [] until the required setting
displays .
IP Address
(your entry)
>
RARP
(current entry)
>
RARP =
(current entry) *
RARP =
(required entry)
d)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
6. Enter the Gateway Address:
a)
Press [] until
displays.
b)
Press []. displays.
Note: Use zeros to supplement each address
segment if fewer than 3 digits are used; e.g.,
13.252.25.08 = 013.252.025.008.
c)
Use the [] or [] key to select the
first digit in the Gateway Address. The
display will scroll from 0 to 9.
d)
Press [] to move to the next digit.
Repeat this procedure to enter the
entire Gateway Address.
e)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
RARP
(your entry)
>
Default Gateway
(current entry)
>
Default Gateway =
(current entry)
Default Gateway
(your entry)
>
7+('2&80(17&203$1<
DC230LP Windows NT
®
4.0 NetBIOS/IP Quick Install
Page 3 of 4
c)
Use the [] or [] key to select the
first digit in the Broadcast Address.
d)
Press [] to move to the next digit.
Repeat this procedure to enter the
entire Broadcast Address.
e)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
9. Enter the Printer (Host) Name:
Note: It is recommended that the Printer (Host)
Name be the same as your Share Name.
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the last character. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to select the
first character in the Printer Name.
Broadcast Addr
(your entry)
>
Printer Name
(current entry)
>
Printer Name =
(current entry)
f)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
11. Enter the Host Name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to enter the
first character of the Host Name.
f)
Press [] to move to the next
character. Repeat this procedure to
enter the entire Host name.
g)
When finished, press [Enter].
**SAVED** displays momentarily,
followed by .
Enablement
Enabled
>
Host Name
(current entry)
>
Host Name =
(current entry)
Host Name
(your entry)
>
f)
Press [] to move to the next charac-
ter. Repeat this procedure to enter the
entire Printer Name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
10.Enable NetBIOS/IP:
a)
Press [Escape] to move back a level
in the menu system.
displays.
Note: TCP/IP must be displayed before
proceeding.
b)
Press [] until
displays.
c)
Press []. displays .
d)
Press []. displays.
e)
Press [] until
displays.
Printer Name
(your entry)
>
TCP/IP
-
>
NetBIOS/IP
>
Enablement
(current entry)
>
Enablement =
(current entry)
*
Enablement =
Enabled
7+('2&80(17&203$1<
DC230LP Windows NT
®
4.0 NetBIOS/IP Quick Install
Page 4 of 4
12.Enter the Printer Name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to select the
first character in the Printer Name.
f)
Press [] to move to the next
character. Repeat this procedure to
enter the entire Printer Name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
Printer Name
(current entry)
>
Printer Name =
(current entry)
Printer Name
(your entry)
>
14.Save all settings:
a)
Press [Online].
displays.
b)
Press [Enter]. displays.
The DC230LP will reboot, save the
settings entered, and print a
Configuration Report in approximately
3 minutes.
15.Check the settings on the Configuration
Report against those that were entered.
16.At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare
®
manual,
Getting Started
with Print and Fax Services
, for additional
information.
Additional information on the Windows NT
NetBIOS/IP setup can be found in the
DC230LP
System Administration Guide, Network
Installation and Troubleshooting
Reset Required
Press ENTER key
Warming Up
Please Wait . . .
>
13.Enter the Workgroup name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the display. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to select the
first character in the Workgroup name.
f)
Press [] to move to the next
character. Repeat this procedure to
enter the entire Workgroup name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
Workgroup
(current entry)
>
Workgroup =
(current entry)
Workgroup
(your entry)
>
©1998 Xerox Corporation
701P98453 Version 1.0, 5-98
-
1
-
2
-
3
-
4
Xerox 230 LP, your new printer, offers a range of capabilities to enhance your printing experience. With its advanced features, you can effortlessly print high-quality documents, take advantage of network connectivity options, and customize your printing settings to meet your specific needs. From crisp text to vibrant graphics, the Xerox 230 LP delivers professional-looking results every time you print.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Xerox 230 LP User manual
-
-
-
-
-
-
-
-
-