2. Xerox
  3. Document Centre 230 LP
Document Centre 230 LP

Xerox Document Centre 230 LP, 230 LP Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Xerox Document Centre 230 LP Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I enable the NetBIOS/NetBEUI protocol on the Xerox 230 LP?
    How do I set the printer name for the Xerox 230 LP?
    How do I set the Host Name for the Xerox 230 LP?
    How do I set the Workgroup name for the Xerox 230 LP?
    How do I save all the settings on the Xerox 230 LP?
7+('2&80(17&203$1<

DC230LP Windows NT
4.0 NetBIOS/NetBEUI Quick Install
1 of 4
c)
Press [], then press [] or [] until.
displays.
d)
Press []. displays.
e)
Use the [] and [] keys to enter
[2222].
Note: 2222 is the factory default password and
may be changed to suit your needs. Refer to the
DC230LP System Administration Guide,
Network Installation and Troubleshooting.
f)
Press [Enter].
displays.
3. Access the NetBIOS/NetBEUI menus:
a)
Press []. displays.
b)
Press [] until
displays.
c)
Press []. displays.
d)
Press [] until
displays.
System
Administration
>
Enter Password
>
System Admin
>
Port Setup
>
Network Setup
>
TCP/IP
>
NetBIOS/NetBEUI
>
4. Enable NetBIOS/NetBEUI:
a)
Press []. displays.
b)
Press []. displays.
c)
Press []. displays.
d)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
5. Select the appropriate interface for your
network:
Note: Token Ring will not be available as a
selection unless it has been installed and
configured.
a)
Press [] until
displays. If Ethernet is the desired
interface, go to step 6.
b)
If Token Ring is the required interface,
press [], then press [] until
displays.
Enablement
Disabled
>
Enablement =
Disabled *
Enablement =
Enabled
Enablement
Enabled
>
Interface
Ethernet
>
Interface =
Token Ring
Installation Requirements:
If this is a Token Ring installation, the Token
Ring card must be installed by your Xerox
service representative and configured before
performing this procedure. Refer to the
Token
Ring Quick Install
card.
Before Installation:
Record the following information for use during
setup at the DC230LP.
Host Name:____________________________
Printer Name: __________________________
Workgroup:____________________________
This installation procedure assumes that you
know how to navigate through the menu system
on the DC230LP Control Panel. Refer to the
quick reference card,
Using the Menu System,
(701P96834) for assistance.
1. Connect the DC230LP to your network
outlet or cable.
2. Access the System Administration menus:
a)
Press [Online] to take the printer off
line. displays.
b)
Press [Menu]. displays.
Printer Off Line
Main Menu
>
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
7+('2&80(17&203$1<

DC230LP Windows NT
NetBIOS/NetBEUI Quick Install
2 of 4
7. Enter the Printer Name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to select the
first character in the Printer Name.
f)
Press [] to move to the next
character. Repeat procedure to enter
entire Printer Name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
Printer Name
(current entry)
>
Printer Name =
(current entry) *
Printer Name
(your entry)
>
8. Enter the Workgroup name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the display. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to select the
first character in the Workgroup name.
f)
Press [] to move to the next
character. Repeat this procedure to
enter the entire Workgroup name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
Workgroup
(current entry)
>
Workgroup =
(current entry) *
Workgroup
(your entry)
>
c)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
6. Enter the Host Name:
a)
Press [] until
displays.
b)
Press []. displays.
c)
Press [] repeatedly until the cursor
reaches the end of the entry. A tone
sounds indicating when the last
character has been reached.
d)
Press [] repeatedly to delete the
current entry.
e)
Use the [] or [] key to enter the
first character of the Host Name.
f)
Press [] to move to the next
character. Repeat this procedure to
enter the entire Host name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
Interface
Token Ring
>
Host Name
(current entry)
>
Host Name =
(current entry) *
Host Name
(your entry)
>
7+('2&80(17&203$1<

DC230LP Windows NT
4.0 NetBIOS/NetBEUI Quick Install
3 of 4
9. Save all settings:
a)
Press [Online].
displays.
b)
Press [Enter]. displays.
The DC230LP will reboot, save the
settings entered, and print a
Configuration Report in approximately
3 minutes.
10.Check the settings on the configuration
sheet against those that were entered to
be sure they are correct.
11. At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare
®
manual,
Getting Started
with Print and Fax Services
, for additional
information.
Additional information on the Windows NT
NetBIOS/NetBEUI setup can be found in the
DC230LP System Administration Guide
,
Network Installation and Troubleshooting.
Reset Required
Press ENTER key
Warming Up
Please Wait . . .
>
7+('2&80(17&203$1<

DC230LP Windows NT
4.0 NetBIOS/NetBEUI Quick Install
4 of 4
©1998 Xerox Corporation
701P98455 Version 1.0, 5-98
/