RCI 9212i Installation guide

Brand: RCI

Model: 9212i

Category: Motorcycle Accessories

Type: Installation guide

USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAmBRIDGE, ON N1T 1j6

PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-mAIl: [email protected]

IS9212i

Pcn13031

R04/13cA

INSTALLATION

9212i

Stand-Alone Keypad

Instructions

Features:

•4IndependentOutputs

•4IndependentTimers

•AllOutputsAssignablebyCode

•Onboard5AmpFormCRelay

•120Users

•RemoteTriggeringInput

•KeypadProgrammable

Memory

Non-volatileEEPROMmemorymeansyourcodesand

programmingwillbetherewhetheryouremovepowerfor

5minutesor5years.

Programming

Allprogrammingisaccomplishedentirelyfromthe

frontofthekeypad.LEDorSounderguidancemakes

programmingeasy,andchangingcodesamatterof

secondsforanauthorizeduser.

Codes

TheRCIkeypadsallowupto120individualusercodes

tobevalid.Codesmaybefrom1-6digitsinlength

anddigitsmayberepeated.TheMasterCodeisalways

assignedtouserlocationone(1).

Main Relay

Thisisa5Amp(10Ampsurge)Form-Crelaywhichcan

betoggledortimedfrom1to90seconds-bycode.

Auxiliary Outputs

Auxiliaryoutputscanbeindividuallytimedfrom1to90

secondsoractasatoggleswitch,andmaybetriggered

individuallyorincombination-bycode.Thethreeauxiliary

outputsprovidea50mAsinktogroundwhenactivated.

Remote Triggering Input

ThisnormallyopenloopthatbydefaultoperatestheMain

Relayuponactivationandcanbeprogrammedtotrigger

anycombinationofoutputs.Uponamomentaryclosure,

theselectedoutputswillenergizefortheirprogrammed

time.Themainrelay(ifselected)willenergizeforthe

sametimeperiodastheMasterCode.Thisfeatureis

especiallyusefulwhencontrollinganelectriclocking

device.

Keypress Feedback / Audible Keypress

TheRCIkeypadswillacknowledgeakeypressby

momentarilyilluminatingtheyellowLED.Thiscanbe

turnedoffthroughprogramming.

Keypad Active Output

TheRCIkeypadscanbeprogrammedtoenergizea

voltageoutputwheneverakeyistouched.Thiscanbe

usedtoturnonaccessoriessuchaslights,CCTVcamera,

ornotifyaguard.

Auto-Entry

Thisfeatureisusedwhentheneedforthecodenotto

befollowedbythe*keyisdesired.Theuseronlyneeds

toentertheircodenumberandtherelaywillactivatefor

theprogrammedrelaytime.Tousethisfeature,theuser

codesmustbethesamelengthasthemastercode.

Technical Notes:

ToavoidESD(Electro-StaticDischarge)frominterfering

withtheoperationoftheRCIkeypad,groundthenegative

terminalofthekeypadtoearthground.Ifthepower

supplycannotbegrounded,thenthecaseshouldbe

grounded.For24VDCoperation,removejumperJ2(see

Fig.5).

Packing Checklist:

9212iKeypad

Ten(10)ConductorWiringHarness(1)

SlottedScrews(2)

SecurityScrews(2)

Installation

Diode(1)

NOTE:Aswithanyelectronicproduct,the9212imaybesubjecttoirregularitiesintheACpowerline.Thiscancausemalfunctionorunstableoperation.

Connectingthe9212itoasuitableDCpowersupplywilllimittheeffectsofACfluctuationonthekeypad.

Voltage Current Rating Temperature Output

 12-24VAC/VDC @12VDC 8mAtyp–35mAw/relayenergized -20°Fto130°F(-28°Cto54°C) Mainrelay:5A;form-C@24VDC;10Asurge

  @24VDC 16mAtyp–45mAw/relayenergized  Outputs2-4are50mAnegvoltageoutputs

Testing the 9212i Keypad

1. Connectthepositive(+)leadofyourpowersupply

totheterminalstrip(TS1)+Vinput.

2. Connectthenegative(-)leadofyourpower

supplytotheterminalstrip(TS1)-Vinput.

3. Turnonyourpowersupply.

4. Press7890#123456*.Ifall12keypresseshave

beenverified,thekeypadwillenterselftestmode.

TheyellowLEDwillflashthreetimes,thenlight

orsoundcontinuouslyfor3seconds.Ifthese

responsesdonothappen,trythetestmodeagain

andthencalltechsupport.Note:selftestmode

canbeusedwhentroubleshootingakeypadinthe

field.Ifyoudonotgetthecontinuouslightthenthe

memoryhasbeencorruptandshouldbe

re-programmedwiththe46command

(seeoption#18).

5. Enterthemastercodeof1234*.Therelaywill

energize.Refertoprogrammingsectiontoprogram

yourkeypad.

Note:The9212ikeypadmaybeprogrammedinyourshop

orattheinstallationsite.Programmedinformationisstored

innon-volatilememorysoitwillnotbelostifpoweris

removed.

RCI Keypad Defaults

RCIkeypadsaredesignedforeasyinstallationina

minimumamountoftime.Thefollowingdefaultshave

beenfactoryprogrammed:

MasterCode(user1) 1234*

MainRelaywillenergizefor 5 seconds

AuxiliaryOutputswillenergizefor 5 seconds

Panicwillenergize Output 4

KeypadActiveOutput Off

RemoteTriggeringInputwillenergize Main Relay

KeypressFeedback On

LEDonwhenpoweredup RED

LEDonwhenrelayisactivated GREEN

Ifdefaultsmustbechangedoradditionalfunctionsare

desired,pleaserefertotheProgrammingOptionschart

afteryouarefamiliarwiththeProgrammingsection.

Programming

1. Enterprogrammingmode YellowLED

 Press 99#(mastercode)* Flashesslowly

2. Tochangemastercode

‡

 Press 1#(newmastercode)* Flashesfast

 Repeat(newmastercode)* Flashesslowly

Ifmainrelaytimemustbechanged,substituteoption2

fromProgrammingOptionschartforstepabove.

3. Toadd/changesecondcode

 Press 2#(newusercode)* Flashesfast

 Repeat (newusercode)* Flashesslowly

4. Toadd/changethirdcode

 Press 3#(newusercode)* Flashesfast

 Repeat (newusercode)* Flashesslowly

5. Upto120codesmaybeaddedinthisfashion

6. Exitprogrammingmode

 Press * Out

Notes:

•Userlocationrepresentsonelocationinmemory 

whereanindividualcodeisstored.Ausercodeisstored

init’sownuserlocation.Thereare120userlocations

available.

•Arecordofalluserlocationsmustbemaintainedto

effectivelymanagekeypadandmaintainpropersecurityof

site.Asampleformisavailablefordownloadat

www.rutherfordcontrols.com-Support-Keypads&

Readerssection.

• Themastercodeallowsaccesstotheprogrammingmode

andactivatesthemainrelay.

• Allcodesmustbefollowedbythe*key.

• Codesmaybefrom1-6digitsinlength,anddigitsmaybe

repeated.

• Ifthemastercodeisforgottenordoesnotseemtobe

working,momentarilypushSW1onthecircuitboard,(see

Fig.5forlocation)toenterprogrammingmodeandfollow

steptwofromabovetoprogramanewmastercode.

• IftheyellowLEDlightssolidwhileinprogrammingmode

anerrorhasoccurred.Press*toclear(yellowLEDshould

flash)andstartoverfromstep2or3above.

‡

Themastercodeisalwaysinuserlocation1.

9212i Keypad Installation Instructions (Continued)

USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAmBRIDGE, ON N1T 1j6

PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-mAIl: [email protected]

Programming Options Chart

Ifthepre-programmeddefaultvaluesmustbechangedoradditionalfunctionsaredesired,thefollowingoptions

maybeprogrammed.

ENTER PROGRAMMING MODE

PRESS 99 # (MASTER CODE) *

Eachofthefollowingoptionscanonlybechangedafterthekeypadhasbeenputintoprogrammingmode(above).

1. Changemastercode/setmainrelaytime

 Press (RelayTime)#1#(newcode)*(repeatcode)*

e.g.Mastercodeof4321/relaytimeof10sec Press 10#1#4321*4321*

2. Add/changeusercode Press (userlocation)#(newcode)*(repeatcode)*

3. Add/changeusercodewithadifferentoutput Press (RelayTime)#(userlocation)#(newcode)*

timeonmainrelay

  (repeatcode)*

4. Deleteusercodes Press (userlocation)#**

5. Setoutput2time

 Press 12#(RelayTime)#0#**

6. Setoutput3time

 Press 13#(RelayTime)#0#**

7. Setoutput4time

 Press 14#(RelayTime)#0#**

8. SetoutputsforRemoteTriggeringInput Press 17#(outputs:.ie.1,2or2,3etc.)#0#**

  Note:0=nooutputs

9. SetoutputsforPanic

 Press 18#(outputs:i.e.1,2or2,3etc.)#0#**

  Note0=nooutputs

10. Turnkeypressfeedback/on Press 30#0#1#**

11. Turnkeypressfeedback/off Press 30#0#0#**

12. TurnyellowLED/sounderOnwithrelay Press 30#1#1#**

13. TurnyellowLED/sounderOffwithrelay. Press 30#1#0#**

14. Turnautoentryon Press 30#2#1#**

15. Turnautoentryoff Press 30#2#0#**

16. Turnkeypadactiveoutputon

 Press 43#0#99#**

17. Turnkeypadactiveoff Press 43#0#00#**

18. Erasekeypadmemory/resetdefaults Press 46#00000#00000#**

19.Energizeselectedoutput(s)withausercode

 Press 59#(outputs:i.e.1,2or2,3etc.)#

  (userlocation)#(newcode)*(repeatcode)*

e.g.User2;codeof4321*;energizeoutputs2&3 Press 59#23#02#4321*4321*

Notes:

 Ifthemastercodeisforgottenordoesnotseemtobeworking,momentarilypushSW1onthecircuitboard,

(seeFig.5forlocation)toenterprogrammingmodeandfollowsteptwofromabovetoprogramanewmaster

code.

 Relaytimemustalwaysberepresentedby2digits.Example:5seconds=05.Latching/toggleisaccomplished

byenteringatimeof00.

 Ifselected,panicwilloperatebypressingthe*and#simultaneously.Panicoperatesfor1secondandis

defaultedtooutput4.

 Keypadactiveisanegativevoltageoutput(sink)availableonterminal(orwire)markedWB(seewiringdiagrams

forlocation).

 Thisfeatureisnotavailablewiththemastercode.

9212i Keypad Installation Instructions (Continued)

USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAmBRIDGE, ON N1T 1j6

PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-mAIl: [email protected]

9212i Keypad Installation Instructions (Continued)

TS1

V+ V- C N/O

–

White/Red

Red

Common

N/C

N/O

Note: See 9212i W

iring Harness details (Fig. 6)

for explanation of Output conductors.

N/C

Fig. 4WiringanAccessoryRelay

Brown

–

Exit Button

(N/O)

TS1

V+ V- N/C C N/O

White/Orange

Fig. 2Basicaccesscontrolwithanelectricstrike

Electromagnetic Lock

–

Exit Button

(N/O)

TS1

V+ V- N/C C N/O

Brown

White/Orange

Fig. 1Basicaccesscontrolw/anelectromagneticlock

–

Exit Button

To Alarm Panel

Closed Circuit Loop

COM N/O

(N/O)

TS1

V+ V- N/C C N/O

Brown

White/Orange

Fig. 3ShuntingaNormallyClosed(N/C)Zone

USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAmBRIDGE, ON N1T 1j6

PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-mAIl: [email protected]

9212i Keypad Installation Instructions (Continued)

USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAmBRIDGE, ON N1T 1j6

PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-mAIl: [email protected]

WHITE

ORANGE

WHITE/ORANGE

BROWN

WHITE/YELLOW

BLACK

RED

WHITE/BLACK

WHITE/RED

WHITE/BLUE

WARNING: Plug this harness in with the leads

facing down! Permanent damage may result if

incorrectly inserted.

Fig. 69212iWiringHarness.

WARNING:Plugthisharnessinwiththeleadsfacingdown!Permanentdamagemayresultifincorrectlyinserted.

Wire Color Wire Function

White NotUsed

White/Blue Output3(50mAsinktoground)

White/Red Output2(50mAsinktoground)

Orange Output4/panic(50mAsinktoground)

Brown RemoteTriggeringInput(REX)

White/Orange RemoteTriggeringInput(REX)

White/Black K(in)KeypadActive

White/Yellow K(out)

Black Ground(outputsonly)

Red V+Filtered(outputsonly)

- Yellow LED

+ Yellow LED

Green LED

Red LED

Green LED

Red LED

J2 – remove

jumper for

24V operation

TS1 Terminal Strip

SW1 Program

Switch

V+ V- N/C C N/O

Fig. 59212iCircuitBoard

RCI 9212i Installation guide

Brand: RCI

Model: 9212i

Category: Motorcycle Accessories

Type: Installation guide

Download PDF

report

RCI 9212i Installation guide

RCI 9212i Installation guide

Related papers

Other documents