RCI 0161 Installation guide

Category
Car kits
Type
Installation guide
Instructions
1) Mark center line (CL) of existing device latch from active door to inactive door.
2) Mark the mounting holes for the Double Door Housing (DDH) on the inactive door.
3) Drill two 13/32” (0.406”) holes through inactive door.
4) Drill wire access hole into desired area of DDH. Pull two (2) wires through the access hole and connect to
strike. (Polarity is not observed)
5) Temporarily mount 0161 strike to DDH through the slotted holes (Hole C) using 1” button head socket cap
screws. (BHSCS)
6) Mount DDH to inactive door using the two (2) 1/4-20x3” screws and 1/4-20” Sex Nuts supplied.
7) Adjust electric strike insert horizontally (If necessary), until Pullman Latch engages when door is closed.
(See Fig. 2 on
0161 installation instructions
if further horizontal insert adjustment is necessary)
8) Mark, drill and tap Hole D for 1/4-20x1” BHSCS provided to secure the final location.
INSTALLATION
0161
Double Door Housing
IS0161DDH PCN110045
R07/11SH
®
©2011 RUTHERFORD CONTROLS INT’L CORP. WWW.RUTHERFORDCONTROLS.COM
USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAMBRIDGE, ON N1T 1J6
PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-MAIL: [email protected]
A 7/8 .875 22.22
B 3-1/2 3.500 88.90
MEASUREMENT
FRACTIONAL
INCHES
DECIMAL INCHES
METRIC (mm)
13/32”
(0.406”)
13/32”
(0.406”)
C
L
A
B
B
0161 Double Door Housing Installation Instructions (con’t)
Typical Double Door Housing Assembly
Double Door Housing
Typical Surface Exit Device
©2011 RUTHERFORD CONTROLS INT’L CORP. WWW.RUTHERFORDCONTROLS.COM
USA: 2517 SQUADRON COURT, SUITE 104, VIRGINIA BEACH, VA 23453 • CANADA: 210 SHEARSON CRESCENT, CAMBRIDGE, ON N1T 1J6
PHONE • 1.800.265.6630 • 519.621.7651 • FAX: 1.800.482.9795 • 519.621.7939 • E-MAIL: [email protected]
0161 DOUBLE
DOOR HOUSING
ACTIVE DOOR
EDGE
DEADLOCKING
TRIGGER
LATCH
C
L
C
L
C
L
C
L
A
B
B
DOOR FACE
INACTIVE
DOOR
EDGE
SCREW
1/4-20 X 3”
STRIKE
INSERT
DRILL
13/32” HOLE
(2 PLACES)
ACTIVE
DOOR
EDGE
TYPICAL SURFACE
EXIT DEVICE
SEX NUT
1/4-20”
HOLE C
SCREW
1/4-20 x 1”
HOLE D
SCREW
1/4-20x1”
HOLE D
SCREW
1/4-20 x 1”
HOLE C
SCREW
1/4-20 x 1”
INACTIVE
DOOR
NOTE: Not to scale. Specifications are subject to change without notice.
  • Page 1 1
  • Page 2 2

RCI 0161 Installation guide

Category
Car kits
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI