INSTALLATION
Read and conform to each of the Pre-Installation instructions
supplied with Rutherford Controls electromagnetic lock.
This product must be used only with a Rutherford Controls
electromagnetic lock.
Failure to conform to these requirements is a misuse of the
product and could result in serious bodily injury or property
damage.
1. Open wiring cavity in front of lock. For remote indication
requiring a closed contact when door is closed, connect the
green lead (NC) and the black lead (COM).
For remote indication requiring a open contact when door is
closed, connect the red lead (NO) and the black lead (COM).
2. Install the DSS Reed Switch into the housing. Take care to
slide the Reed Switch to the bottom of the housing to ensure
reliable operation.
NOTE: When connecting to the reed switch leads, the connections
should be soldered or correct size Marrettes™/Wire Nuts™ must
be used. The ‘DSS’ option reed switch contacts are rated at 0.20A
@ 12VDC and 0.12A @ 24VDC. Do not exceed this rating.
3. Replace standard armature plate with longer DSS armature
plate. Apply thread locking compound to bolt before
re-engaging into sexnut.
NOTE: During installation of the armature plate to the door it is
essential that the armature plate remains movable. The armature
plate must be allowed to pivot on the center-mounting bolt to
allow proper alignment with the magnet surface. If the plate is not
aligned with the magnet surface, the lock may lose holding force
or not lock at all.
The head of the armature mounting bolt ships with a rubber
washer affixed to it. This washer should project slightly beyond
the surface of the armature plate. This is to allow the washer
to expand when power is removed and break the air vacuum
between the plate and the magnet surface. If this washer is
removed or trimmed the lock will appear to have some holding
force even when power is removed.
WARNING: Improper installation, maintenance, inspection
or usage of this or any related product may cause the
electromagnetic lock, armature plate and associated hardware
to disengage and fall, causing serious bodily injury and
property damage. dormakaba Canada Inc. will not be liable to
the installer, purchaser, end user or anyone else for damage or
injury to person or property due to improper installation, care,
storage, handling, maintenance, inspection, abuse, misuse or
act of God or nature involving this or any related product.
8 series
ISDSS PCN18003
R03-18GR-1
Maintenance
This product and all related accessories or parts must be inspected and maintained on a quarterly basis. Contacting surfaces of the electromagnetic
lock and armature plate must be kept free of contaminating materials. Surfaces should be cleaned periodically with a non-abrasive cleaner.
All mounting fasteners must be inspected on a quarterly basis. When properly installed the ends of the armature plate allow a slight movement, but
the plate will feel secure when grasped at the bolt. There should be no movement to the mounting bracket or housing of the electromagnetic lock.
Instructions
(Wiring directly to the ‘DSS’ Option Reed Switch)
DSS RETROFIT
ELECTROMAGNETIC LOCK ACCESSORY
INSTALLATION
®
Read and conform to each of the Pre-Installation instructions
supplied with Rutherford Controls Int’l Corp. electromagnetic
lock. Failure to conform to the Pre-Installation instructions is a
misuse of the product and could result in serious bodily injury or
property damage.
This product must be used only with a Rutherford Controls Int’l
Corp. electromagnetic lock. Failure to conform to this requirement
is a misuse of the product and could result in serious bodily injury
or property damage.
1. Open wiring cavity in front of lock. For remote indication
requiring a closed contact when door is closed, connect the
green lead (NC) and the black lead (COM).
For remote indication requiring a open contact when door is
closed, connect the red lead (NO) and the black lead (COM).
2. Install the DSS Reed Switch into the housing. Take care to
slide the Reed Switch to the bottom of the housing to ensure
reliable operation.
NOTE: When connecting to the reed switch leads, the connections
should be soldered or correct size Marrettes™/Wire Nuts™ must
be used. The ‘DSS’ option reed switch contacts are rated at 0.20A
@ 12VDC and 0.12A @ 24VDC. Do not exceed this rating.
3. Replace standard armature plate with longer DSS armature
plate. Apply thread locking compound to bolt before re-
engaging into sexnut.
NOTE: During installation of the armature plate to the door it is
essential that the armature plate remains movable. The armature
plate must be allowed to pivot on the center-mounting bolt to
allow proper alignment with the magnet surface. If the plate is not
aligned with the magnet surface, the lock may lose holding force
or not lock at all.
The head of the armature mounting bolt ships with a rubber
washer affixed to it. This washer should project slightly beyond
the surface of the armature plate. This is to allow the washer to
expand when power is removed and break the air vacuum between
the plate and the magnet surface. If this washer is removed or
trimmed the lock will appear to have some holding force even
when power is removed.
WARNING: Improper installation, maintenance, inspection or
usage of this or any related product may cause the
electromagnetic lock, armature plate and associated hardware
to disengage and fall, causing serious bodily injury and
property damage. Rutherford Controls Int'l Corp. will not be
liable to the installer, purchaser, end user or anyone else for
damage or injury to person or property due to improper
installation, care, storage, handling, maintenance, inspection,
abuse, misuse or act of God or nature involving this or any
related product.
DSS Reed Switch
8 SERIES
ISDSS PCN070022
P01/08DA
©2008 RUTHERFORD CONTROLS INT’L CORP. WWW.RUTHERFORDCONTROLS.COM
USA: 2697 INTERNATIONAL PARKWAY, PKWY 5, VIRGINIA BEACH, VA 23452 • CANADA: 210 SHEARSON CRESCENT, CAMBRIDGE, ON N1T 1J6
PHONE • 1.800.265.6630 • 519.621.7651 • FAX: • 519.621.7939 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM
Maintenance
This product and all related accessories or parts must be inspected and maintained on a quarterly basis. Contacting surfaces of the electromagnetic
lock and armature plate must be kept free of contaminating materials. Surfaces should be cleaned periodically with a non-abrasive cleaner.
All mounting fasteners must be inspected on a quarterly basis. When properly installed the ends of the armature plate allow a slight movement, but the
plate will feel secure when grasped at the bolt. There should be no movement to the mounting bracket or housing of the electromagnetic lock.
Instructions
(Wiring directly to the ‘DSS’ Option Reed Switch)
Position stripe close
to wiring cavity
Inside Details
of Endcap
DSS RETROFIT
ELECTROMAGNETIC LOCK ACCESSORY
© 2018 dormakaba Canada Inc.
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: [email protected]
-
1
Dormakaba 8310/8320 DSS Kits Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
RCI 8310 Installation guide
-
-
-
-
-
RCI IntelliMag 8340-IQ Installation guide
-
-
Dormakaba BML-8371 User manual
-
Dormakaba Saflok Quantum RFID User guide
-
FSH FEM5700DM Technical Manual
