RCI 9212ilw User manual

Brand: RCI

Model: 9212ilw

Category: Security access control systems

Type: User manual

IS9212iLW

Features:

• FlushMount,SingleGang

•IlluminatedBacklitKeys

•KeypadProgrammable

• KeypressFeedbackviaBuilt-InSounder

•Bi-ColorRed/GreenLEDIndicatesRelayStatus

•YellowLEDIndicatesProgramMode

•120Users

•SingleUseCodes

•LockoutUsers

•Passage/ToggleCodes

•10to30VoltDCOperation

•12to24VoltACOperation

•2AmpMainRelay

•RemoteTriggerInput(REX)

• 2YearWarranty

Product Description:

The212iLWkeypadfeaturesasingle-relayoutputtocontrolany

devicerequiringanon/offswitch.Theoutputistimedorlatchedand

operatedbyauser’sPINcode.Additionally,the212iLWkeypad

providesbasickeylessentrybycontrollingadoorlockingdevice

wheresecurityisnotanissue.

The212iLWstylekeypadsaredesignedforbothindoorandoutdoorush

mountapplications.Theelectronicsareconformalcoatedinthe

manufacturingprocessinordertoprovidethislevelofapplication

exibility.Inaddition,eachkeypaduseshardenedkeystoassurelong-term,

high-qualityperformance.

Eachkeypadcontainsilluminatedclearkeysthatmakeoperationinlow

lightsituationseasyandaccurate.iLWstylekeypadsmounttoanystandard

single-gangelectricalboxordirectlytoanywall.

Speciﬁcations:

Parameter Range/Description

Voltage 10–30VDC,12-24VAC(Auto-Adjusting)

Current 93mA@10VDC;158mA@30VDC,148mA@12VAC;198mA@24VAC

Environment ForIndoorandOutdoorUse

TemperatureTolerance -20°Fto130°F(-28°Cto54°C)

Dimensions 51/8”Hx33/8”Wx5/8”D

MainRelay(FormC) ContactRating:2A@30VAC/DC

REXInput NormallyOpenDryContact

DoorPositionInput NormallyClosedDryContact

LEDs Bi-ColorRed/Green;Yellow

Default Keypad Settings

Parameter Default Setting

MasterCode 1234

LockOutput Relay1(Mainrelay)

AudioAlerts Notassigned

REX TriggersLockOutput

REXOperation AlwaysTriggers(regardlessofDoorLoop)

ErrorLockout/Threshold Enabled/3Attempts

ErrorLockoutDuration 10seconds

LockOutputTime 5seconds

Visual/AudioKeypressFeedback Enabled

Auto-Entry Disabled

UserLockout

Enabled

PCN13023

R11/13CA

INSTALLATION

9212iLW

Interior/Exterior Use Stand-Alone Keypad

usA: 2517 sQuAdRon couRt, suIte 104, VIRGInIA BeAch, VA 23453 • cAnAdA: 210 sheARson cRescent, cAmBRIdGe, on n1t 1j6

Phone • 1.800.265.6630 • 519.621.7651 • fAX: 1.800.482.9795 • 519.621.7939 • e-mAIl: [email protected]

9212iLW Keypad Installation Instructions (Continued)

usA: 2517 sQuAdRon couRt, suIte 104, VIRGInIA BeAch, VA 23453 • cAnAdA: 210 sheARson cRescent, cAmBRIdGe, on n1t 1j6

Phone • 1.800.265.6630 • 519.621.7651 • fAX: 1.800.482.9795 • 519.621.7939 • e-mAIl: [email protected]

MOUNTING

Thekeypadisdesignedtobeushmountedusingastandardsinglegangelectrical

box.Inaddition,itcanbeushmounteddirectlytothewallsurfacebycuttingahole

inthewall.Toproperlysizethemountingandwireaccesshole,usetheinstallation

templateonthelastpageinthismanual.

Mountingheightcanvarydependingonrequirements.Anappropriaterangeis

typicallybetween48and52inchesoncenterofftheoor.

Foroutdoorinstallations,useaweatherproofbackboxandsealthewireentrylocations

withsiliconeandprovideadrainhole.Inaddition,usetheanti-oxidantgreasepackfor

thewireharnessconnectors.

Figure 1 Keypad

MountingHeight

WIRING : Wire Harness Conﬁguration

Figure 2 Keypad Connector

and Wire Harness

Pin Wire Color Signal name

1 Red V+(KeypadPower)

2 Black V-(KeypadPower)

3 White/Black NotUsed

4 White/Yellow NotUsed

5 Brown RemoteTrigger(REX)

6 White/Orange LoopCommon(REXandDoorLoop)

7 White DoorLoopMonitor

8 Green MainRelay–NormallyOpen

9 Blue MainRelay-Common

10 Gray MainRelay–NormallyClosed

Wiring the Keypad to a Maglock (Fail-Safe)

UsethefollowingstepstoconnectthekeypadtoaMaglock

(Fail-Safe):

 1.Connecttheredwire(V+)tothebluewire(common),andthen

  connectthemtothepositiveonthepowersupply.

 2.Connectthegraywire(normallyclosed)tothepositiveonthe

  Maglock.

 3.Connecttheblackwire(V-)tothenegativeontheMaglock,and

  thenconnectthemtothenegativeonthepowersupply.

Figure 3 WiringtheKeypadtoa

Maglock(Fail-Safe)

Wiring the Keypad to an Electric Strike (Fail-Secure)

Usethefollowingstepstoconnectthekeypadtoanelectricstrike

(fail-secure)(seeFigure4forreference):

 1. Connecttheredwire(V+)tothebluewire(common),andthen

  connectthemtothepositiveonthepowersupply.

 2. Connectthegreenwire(normallyopen)tothepositiveonthe

  strike.

 3. Connecttheblackwire(V-)tothenegativeonthestrike,and

  thenconnectthemtothenegativeonthepowersupply.

Figure 4 WiringtheKeypadtoan

ElectricStrike(Fail-Secure)

9212iLW Keypad Installation Instructions (Continued)

usA: 2517 sQuAdRon couRt, suIte 104, VIRGInIA BeAch, VA 23453 • cAnAdA: 210 sheARson cRescent, cAmBRIdGe, on n1t 1j6

Phone • 1.800.265.6630 • 519.621.7651 • fAX: 1.800.482.9795 • 519.621.7939 • e-mAIl: [email protected]

Shunting a Normally Closed Zone

Usethefollowingstepstousethekeypadtoshuntanormallyclosed

zone:

 1.Connectthebluewire(common)tothecommonconnectionon

  thedoorpositionswitch.

 2.Connectthegreenwire(normallyopen)tothenormallyclosed

  connectiononthedoorpositionswitch.

Figure 5: Shunting a Normally Closed Zone

Wiring Remote Trigger as Request to Exit (REX)

Button and Door Contacts

Use the following steps to connect the keypad to a normally

open REX device and normally closed door switch:

1. Connect the brown wire (REX Input) to the normally

open connection on the REX device.

2. Connect the white/orange (loop common) to the

common on the REX device and the common on the

door switch.

3. Connect the white wire (door loop) to the normally

closed connection on the door switch.

NOTE:

Doorloopdoesn’tneedtobeclosedfortheREXfunctiontooperate,by

default,butsettingoption8to0undercommand30,programstheREXfunctionto

operateonlywhenthedoorloopisclosed.ThispreventstheREXfromre-triggering

whenthedoorisopen

Figure 6: Wiring a REX Button

and Door Contacts

TESTING THE KEYPAD

After installing the keypad, RCI recommends that you perform the keypad self-test once a year, to ensure that the keypad works properly.

1. To perform the self-test, with the unit powered up, press the following keys on the keypad: 7890#123456*

   •Ifall12keypressesareaccepted,thekeypadentersself-testmode.

   •TheLEDsalternategreen,yellow,andredfollowedbythesounderbeepingthreetimes.

2. Verify that the master code works correctly. (The master code accesses program mode and activates the main relay to verify that

the locking device is working.)

The default master code is 1234. (If the default is not working, refertoWIREHARNESSLOOPBACKCONNECTIONSsectiononpg.6)

PROGRAMMING

Toenterprogrammode,press99#MasterCode*.TheyellowLEDmustthenstartblinkingslowing(ifnotverifythemastercodeis

correct–refertoWIREHARNESSLOOPBACKCONNECTIONSsection).ThedefaultMasterCodeis1234.

NOTE: If auto-entry is enabled, the * (asterisk) key is not used to enter Program mode. To change the Master Code, enter:

1 # new Master Code * new Master Code * (When ﬁnished press the * to exit program mode.)

Note: RefertoPROGRAMMINGUSERSsectiononpg.4foraddingusercodes

A record of all user locations must be maintained to effectively manage keypad and maintain proper security of site. A sample form is

available for download at www.rutherfordcontrols.com - Support - Keypads & Readers section.

To Alarm Panel

9212iLW Keypad Installation Instructions (Continued)

usA: 2517 sQuAdRon couRt, suIte 104, VIRGInIA BeAch, VA 23453 • cAnAdA: 210 sheARson cRescent, cAmBRIdGe, on n1t 1j6

Phone • 1.800.265.6630 • 519.621.7651 • fAX: 1.800.482.9795 • 519.621.7939 • e-mAIl: [email protected]

PROGRAMMING USERS

To enter program mode press 99 # master code *.

Command/Action Keys to Enter/Details

MasterCode

User#1isthemastercode;itcanaccessallcommandsinprogrammode.Thedefaultcodeis1234.Themastercode

canbeprogrammedwith60asastandarduseronly.

SupervisorCode

User#2,whenprogrammed,isthesupervisorcode.Thesupervisorcanaccessprogrammode,butislimitedto

addinganddeletingusers,aswellasenablingordisablingusers.Thesupervisorcodecan’tchange,delete,ordisable

themastercodeorsupervisorcodeitself.

AddStandardUser (shortversion)userlocation#code*code*

AddUserwithSpecicUnlock

Time

unlocktime#userlocation#code*code*(Thiscommandisusedtoprogramauserwithaspecicunlocktime.

Thisuseractivatesthevirtuallockoutput.)

DeleteUser userlocation#**

Command 60.

Add/ModifyEnhancedUser

60 # user type # user location # code * code *

(codescanbefrom1to10digitsinlength)

User Types

0–ToggleUser

1–StandardUser

3–LockoutUser

5–SingleUseCode

7–EmergencyUser

8–DuressUser

9–Two-PartUserTypeA

10–Two-PartUserTypeB

ToggleUser Atoggleuserlatchesthevirtuallockoutput.

StandardUser Activatesthevirtuallockoutputusingthelockdurationprogrammedwithcommand11.

LockoutUser

Thisusertypelocksoutusersinuserlocationshigherthanthelockoutuserwhenthelockoutusercodeisentered.

Forexample,ifthelockoutuserisprogrammedforuser20,anyuserinlocation21to120islockedoutandtheir

codesnolongerworktogainaccess.Alockoutisremovedbyenteringthesamelockoutcode.Ifanotherlockoutcode

inanotheruserlocationisentered,thelockoutuserlocationlevelissettothenewlockoutuserlocation.Themaster

codeandemergencyuserscan’tbelockedout.Thecurrentlockoutisclearedwhenprogrammodeisentered.“Lock-

outactivated”isindicatedbytwodoublebeeps.“Lockoutcanceled”isindicatedbyonedoublebeep.“Accessdenied

duetolockout”isindicatedby1longbeepfollowedby3shortbeeps.“Userlockout”canbeenabledordisabledwith

command30.

SingleUseCode

Thiscodecanonlybeenteredoncetogainaccessusingthelockvirtualoutput.Onceused,thiscodeisnolonger

active.Asingleusecodecanbeveriedbyentering5#code*.Ifthecodeisasingleusecode,thegreenLEDashes

for½asecond.An“invalidcode”isindicatedby3quickbeeps.

EmergencyUser Thisusertypeisastandarduserthatcannotbelockedoutbyalockoutuser.

DuressUser

Enteringaduresscodeactivatesthelockandduressvirtualoutputs.Thisallowsyoutotriggeranotherdevicesilently,

suchasanalarm,andstillgainaccessincaseofanemergency.

Two-PartUsersAandB

Whenthetwo-partuseroptionisenabled,twocodesarerequiredtogainaccess.A“Two-PartTypeA”and“Two-Part

TypeB”usermustentertheircode(notnecessarilyinthatorder).Aftertherstcodeisentered,theLEDalternates

betweenredandgreen,indicatinganothercodeisrequired.Thesecondcodemustbeenteredwithin15secondsof

therstcode.Whentwocodesofthesametypeareentered,atypemismatchisindicatedby5beeps.WhenTwo-

PartUserisdisabled,allTypeAandBusercodesareconvertedtostandardusercodes.

Two-Partusersactivatethevirtuallockoutput.Two-PartUserscanbeenabledordisabledwithcommand30.

Command 56.

Enable/DisableUser

56 # enable/disable # user location # * *

Options:

1=Disable

0=Enable

Themastercodeandsupervisorcodecan’tbedisabled.

9212iLW Keypad Installation Instructions (Continued)

usA: 2517 sQuAdRon couRt, suIte 104, VIRGInIA BeAch, VA 23453 • cAnAdA: 210 sheARson cRescent, cAmBRIdGe, on n1t 1j6

Phone • 1.800.265.6630 • 519.621.7651 • fAX: 1.800.482.9795 • 519.621.7939 • e-mAIl: [email protected]

PROGRAMMING KEYPAD OPTIONS

To enter program mode press 99 # master code *.

Command/Action Keys to Enter/Details

Command 30.

Enable/Disable

KeypadOptions

30 # option # enable/disable # * *

Option

0–AudioKeypressFeedback

1–VisualKeypressFeedback

2–AutoEntry

3–ErrorLockout

4–UserLockout

5–Two-PartUsers

6–KeypadIllumination

7–KeypadDimming

8–REXOperation

Disable

0=disabled

0=disabled

0 = disabled

0=disabled

0=disabled

0=onlywhendoorloopclosed

Enable

1 = ENABLED

1=ENABLED

1 = ENABLED

1 = ALWAYS

AutoEntry

Whenauto-entryisenabled,userswithcodesthesamelengthasthemastercodedonothavetopressthe*keyafterenteringtheir

code.Ifyouhaveacodegreaterthanthemastercode,youcanuseAuto-EntrySuspend.Justenterthe#keypriortoyourcode

followedbythe*key.

Example:#23456*ifthemastercodeisfourdigits.

Command 32.

ChangeKeypadParameters

32 # parameter # value # * *

Parameter

0-DuressOutputDuration

1-PanicOutputDuration

2-ErrorLockoutThreshold

3-ErrorLockoutDuration

Value

1-255(default=5)

1-50(default=3)

1-255(default=10)

ErrorLockout

Whenenabled,thekeypadkeepstrackofthenumberofconsecutiveinvalidcodesentered,includingattemptsto

accessprogrammode.Whenthethresholdisreached,theyellowLEDturnsonsolidandthekeypadnolongerrespondstokey

pressesfortheprogrammedtimeduration.Thecountisresetbyenteringavalidcode,includingenteringprogrammode.

KeypadIllumination Keypadbacklightingcanbeenabledordisabled.

KeypadDimming

Whenenabled,thebacklightingilluminationleveldecreases15secondsafterthelastkeypress.Whendisabled,thebacklighting

remainsatfullilluminationatalltimes.

Command 40.

ResetDefaultsOnly

40 # 00000 # 00000 # **(mastercode,allkeypadoptionsandparameters)

Command 46.

EraseUsersandResetDefault

Settings.

46 # 00000 # 00000 # **

PROGRAMMING OPTIONS CHART - QUICK REFERENCE

To enter program mode press 99 # master code *.

Command/Action Keys to Enter/Details

AddStandardUser

user location # code * code *

AddStandardUserwithSpecic

UnlockTime

unlocktime#userlocation#code*code*

Add/ModifyEnhancedUser 60#usertype#userlocation#code*code*(refertoPROGRAMMINGUSERSsectiononpg.4fordetails)

DeleteUser userlocation#**

SetLOCKOutputTimeDuration 11#time#0#**(1to255seconds)

Enable/DisableKeypadOptions 30#option#enable/disable#**(refertoPROGRAMMINGKEYPADOPTIONSsectiononpg.5fordetails)

Enable/DisableUser 56#enable/disable#userlocation#**

ResetDefaultsOnly

40 # 00000 # 00000 # **

EraseUsersandResetDefault

Settings

46 # 00000 # 00000 # **

9212iLW Keypad Installation Instructions (Continued)

usA: 2517 sQuAdRon couRt, suIte 104, VIRGInIA BeAch, VA 23453 • cAnAdA: 210 sheARson cRescent, cAmBRIdGe, on n1t 1j6

Phone • 1.800.265.6630 • 519.621.7651 • fAX: 1.800.482.9795 • 519.621.7939 • e-mAIl: [email protected]

TROUBLESHOOTING

Refer to this section if the keypad is not operating correctly as described in this manual.

Problem Solution

TheLEDsareslowlycycling

fromrighttoleftand

backlightingisoff.

The keypad is designed to monitor the input voltage and this is an indication of under-voltage.

The under-voltage threshold is set to 8.5VDC, and when the voltage drops below this limit, the low

voltage warning starts and backlighting is turned off. To solve, raise the voltage to between 12-24V.

TheLEDsarerapidlycycling

fromlefttorightandthekeypad

haslostalloperation.

Thekeypadisdesignedtomonitortheinputvoltage,andthisisanindicationofover-voltage.

Theover-voltagethresholdissetto36VDC,andwhenthevoltagerisesabovethislimit,the

overvoltagewarningstartsandthekeypadlosesalloperation.Tosolve,verifyvoltageiscorrectat

powersupply.

Themastercodedoesnotwork.

Performtheprogrammingmodeloopbackandresetthemastercodeusingtheprogramming

command.

NoLEDsarelitonthekeypad

Powerisnotreachingthekeypad.Usingavoltmeter,conrmthatthereisvoltageatthe

keypadontheredandblackwires.Ifthereisnovoltageatthekeypad,verifythatthereisvoltage

atthepowersupply.Ifthereisnovoltageatthepowersupply,callthemanufacturerofthepower

supply.Ifthereisvoltageatthepowersupplybutnotatthekeypad,verifythereisnobreakinthe

wires,thencheckcontinuityinthewholelengthofthewirerun.Toverifythatthekeypadis

working,youcanpowerthekeypadwitha12-VoltBattery.



If the keypad still does not work after troubleshooting, please call RCI’s techinal support department at

1-800-265-6630 or 519-621-7651.

WIRE HARNESS LOOPBACK CONNECTIONS

IftheMasterCodeiseithernotworkingorforgotten,powerdownthesystem,

connectthewireharnessasshowninFigure7below,andthenpowerthe

systemupagain.Theunitshouldnowbeinprogrammode.Next,change

yourMasterCodeusingtheprogrammingcommandandpowerdownthe

systemandrestorethewireharnesstoitsoriginalcongurationandpower

thesystembackup.

Figure 7 ProgramModeLoopback

White/Yellow

Brown and White

RCI 9212ilw User manual

Brand: RCI

Model: 9212ilw

Category: Security access control systems

Type: User manual

Download PDF

report

RCI 9212ilw User manual

RCI 9212ilw User manual

Related papers

Other documents