FläktGroup FICO PRO (FCLB-256) Installation guide

FläktGroup
Brand
FläktGroup
Model
FICO PRO (FCLB-256)
Type
Installation guide
OPERATION GUIDE
ISYteq FICO PRO
and associated equipment
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
2
FICO PRO - Operation Guide
CONTENTS, COMMON ACRONYMS AND UNITS
CONTENTS
1 GENERAL ........................................................................................................................................................................................................................................... 3
2 PROPERTIES & FUNCTIONS ......................................................................................................................................................................................................... 3
2.1 EASY TO ENGINEER ....................................................................................................................................................................................................... 3
2.2 EASY TO USE .................................................................................................................................................................................................................. 3
2.3 DAMPER TESTING .......................................................................................................................................................................................................... 4
3 AUTOMATION SYSTEM .................................................................................................................................................................................................................. 4
3.1 EXTERNAL INPUT AND OUTPUTS ............................................................................................................................................................................. 4
3.2 SERVICE MODE .............................................................................................................................................................................................................. 4
3.3 FAN INTERLOCKING RELAYS ..................................................................................................................................................................................... 4
4 LEVELS OF AUTHORITY ................................................................................................................................................................................................................ 5
4.1 LOST PASSWORD ........................................................................................................................................................................................................... 5
5 SETTINGS ........................................................................................................................................................................................................................................... 5
5.1 SETTING THE TIME ......................................................................................................................................................................................................... 5
5.1.1 CHANGING THE SYSTEM TEST SCHEDULE ................................................................................................................................................ 5
5.1.2 MANUAL TEST DAMPERS ................................................................................................................................................................................ 5
5.2 SERVICING THE DAMPERS IN THE SYSTEM ........................................................................................................................................................ 6
5.3 ALARMS IN THE FICO PRO System ......................................................................................................................................................................... 6
5.3.1 ALARMS IN A MULTI-BOX (SLAVE) .............................................................................................................................................................. 6
6. ACCESSORIES .................................................................................................................................................................................................................................. 6
7 DRAWINGS........................................................................................................................................................................................................................................ 7
7.1 FICO PRO ........................................................................................................................................................................................................................... 7
7.2 SYSTEM CONNECTION .................................................................................................................................................................................................. 8
8. NOTES .............................................................................................................................................................................................................................................. 9
COMMON ACRONYMS AND UNITS
ISYteq FICO PRO or PRO FCLB-256
FCBB - 2/4 Multi-boxes (slaves)
Rel. Relay
HMI 7-Touch colour screen
MM2 Millimetres squared
AC Alternating voltage
Modbus RTU Modus remote terminal unit
SELV Safety Extra low voltage
PELV Protective extra-low voltage
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
3
FICO PRO - Operation Guide
GENERAL, PROPERTIES AND FUNCTIONS
1 GENERAL
The monitoring system ISYteq FICO-PRO is designed for monitoring
and testing motorized fire dampers. The system consists of a control
unit FCLB-256 as the main unit, which can directly accommodate the
connection of up to 4 fire dampers and multi-boxes ISYteq FCBB-
2 & FCBB-4. The multi-boxes can control two or four fire dampers
respectively and they are installed close to the fire dampers. The
FCBBs are installed in a suitable location with the system able to
control 256 fire dampers and 128 smoke detectors with individual
status indications. The fire dampers can be divided into multiple groups
with each of them including ventilation interlocking.
- FICO PRO
- FCBB-2
- FCBB-4
The PRO control unit has four internal relay units for the connection of 4
number fire dampers and 2 smoke detectors. Additionally, the PRO has
4 volt-free relays, 3 are assigned by default for the connection of a fire
alarm contact, a service alarm contact and a fan control contact. Digital
inputs of which there are 3 for external test switch, external interlock
or external fire alarm.
The communication with the multi-boxes is via Modbus RTU
communication protocol and must be connected in a daisy chain,
looping in and out from each multi-box after the PRO master device.
The complete system can consist of 1 PRO and up to 63 FCBB multi-
boxes. Care in the design of the system should be taken as the
maximum number of multi-boxes in a single system can not exceed
63 regardless of whether FCBB-2 or FCBB-4 multi-boxes are used.
Manual function control can be performed from the control unit for a
damper group with several different settings: the whole system, group
by group, for a single multi-box or a single damper (Note! Single multi-
box or single damper test can only be performed if the multi-box or
damper have been assigned to an individual group). In addition, a
manual function control can be run using a push button on the multi-
box. The system’s flexibility allows for a system test of dampers or
groups separately, therefore removing the need to shut down the
AHU if required to continue running for a critical application. A built-in
schedule allows for testing of the fire dampers to be carried out at the
most convenient times.
The modular construction of the ISYteq FICO system allows for a
flexible installation and commissioning approach, as the system can
be easily extended with more multi-boxes.
The HMI is a 7-inch colour touchscreen and utilises the ISYteq controls
tile format to display the system and for easy navigation of the system.
Alarm indications are quickly seen and can be easily read for quick
action. A Modbus connection from the FICO PRO can be connected to
the building management system for remote indication of operating
status.
2 PROPERTIES AND FUNCTIONS
FICO PRO - for the control and management of four 24V fire damper
actuators directly connected and the control and management of up to
a further 252 24V damper actuators via the Multi-boxes FCBB-2 and
or FCBB-4. The unit firmware incorporates a calendar for the set-up of
regulated testing.
2.1. Easy to engineer
The control unit contains all essential functions and ensures safe
installation. The system has two data transfer loops to which the
multi boxes are connected in series using, for instance, FQAR-PG
2x0.5 (1 twisted pair) Modbus data transfer cable can be used for the
connection. The maximum length of the cable is 1100 m in each loop.
This makes it easy to connect new multi-boxes to an existing system.
The power supply voltage for the control unit and the multi-boxes is
230 VAC. Each multi-box supplies 24 VAC max. to 2 or 4 dampers.
The maximum number of smoke detectors connected to a multi-box is
two. As part of the installation, the system can be divided into groups.
Each FICO PRO and FCBB multi-box requires a 230VAC connection
using a power cable type such as EQQ 3x1.5 mm2. See the cabling
requirements on page 7.
2.2. Easy to use
The control unit panel has a
7-inch colour touchscreen
display, with LED indicators
on the multi-box control
board, which can be seen
through the clear box cover.
All functions, settings and
readings are accessible
through the menu system.
The settings are protected
with three levels that require passwords. The possibility to read room
status through the multi-box makes monitoring quick and easy.
Screen Menu
Show main menu.
Jump to the home screen and see information about the
logged-in user.
Green = Administrator
Yellow = Service
Messages.
Operation mode – Green = Online mode | Red = Offline mode
Network information – The colour of the icon depicts the
network status.
White = Network-enabled and network cable connected The
device has an IP assigned | Yellow = Network inactive.
Product system information
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
4
FICO PRO - Operation Guide
PROPERTIES AND FUNCTIONS, AUTOMATION SYSTEM
Main Screen
Tile layout allows for easy and quick navigation.
The FCBB multi-boxes are supplied with clear covers which allows for
viewing the LED indication as follows.
ALARM
STATUS
OPEN
CLOSE
FIRE
SERVICE
SERVICE
LINK
OPEN
CLOSE
FIRE
SERVICE
STATUS Power SERVICE
ALARM LINK Communication
OPEN Damper 1, Open OPEN Damper 2, Open
CLOSE Damper 1, Closed CLOSE Damper 2, Closed
FIRE Detector 1, Alarm FIRE Detector 2, Alarm
SERVICE Detector 1, Service alarm SERVICE Detector 2, Service alarm
Indication on the circuit board for FCBB-2
ALARM
STATUS
OPEN
CLOSE
OPEN
CLOSE
SERVICE
LINK
OPEN
CLOSE
OPEN
CLOSE
FIRE
SERVICE
FIRE
SERVICE
STATUS Power SERVICE
ALARM LINK Communication
OPEN Damper 1, Open OPEN Damper 2, Open
CLOSE Damper 1, Closed CLOSE Damper 2, Closed
OPEN Damper 3, Open OPEN Damper 4, Open
CLOSE Damper 3 Closed CLOSE Damper 4, Closed
FIRE Detector 1, Alarm FIRE Detector 2, Alarm
SERVICE Detector 1, Service alarm SERVICE Detector 2, Service alarm
Indication on the circuit board for FCBB-4
2.3. Damper testing
Damper function control can be run automatically at set intervals for
the whole installation at the same time. Manual function control can
be run from the control unit or the multi-box. From the control unit, you
can select testing of the whole system, a group, a single multi-box, or a
single fire damper if these have been assigned to their own group.
3 AUTOMATION SYSTEM
The FICO PRO control unit can be connected to a building automation
system through a Modbus protocol connection. This makes it possible
to monitor the FICO’s functions, e.g., damper status, smoke detector
status, and fire and service alarms.
3.1. External inputs and outputs
- Fire alarm output
- Service alarm output
- External fire alarm input
- External interlock input, enabling damper closing without alarm.
- Built-in data transfer via Modbus as standard.
- Fan/AHU control outputs
- External damper test
- External reset inputs
3.2. Service mode
Single multi-boxes can be set to service mode to facilitate repair
work on rooms or ventilation or ventilation extension work. In this
mode, the multi-box is not activated. After a set time the multi-box will
automatically return to an activated state.
3.3. Fan interlocking relay
Standard delivery includes four built-in relays in the ISYteq FICO PRO,
further relays to extend the system for controlling ventilation equipment
groups are possible with the use of the FCIO-88 which has 8 relay
outputs. The system can be extended to handle up to 63 multi-boxes
and a total of 256 fire dampers. The whole system (256 fire dampers)
can be contained in a single group. In the event of a fire alarm being
triggered all dampers automatically close, and a signal to the AHU can
be sent to shut down or operate certain extract functions alongside or
separate to smoke extract fan/s.
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
5
FICO PRO - Operation Guide
LEVELS OF AUTHORITY, SETTINGS
4 LEVELS OF AUTHORITY
The PRO device is password protected and to make changes to the
system design, add users etc., you need to have administrative rights
to the system. You will have to be logged in to the FICO PRO as the
administrator, (more than one person can be an administrator).
This should only be configured by qualified staff as some functions may
cause damage to the unit or surroundings if not set up correctly (e.g.,
fire, service alarms or testing the system)
Creating user accounts
1. Go to the users’ overview by clicking the “USERS“-tile.
2. If you haven’t already logged into a user with admin access or similar
do so now.
3. Press the “New“-button in the upper right corner.
4. Enter a username, password, and additional information at will. Then
press “OK“.
5. Edit the user by clicking the pencil symbol right next to it.
6. You can now change the information but also change the access
level you would like the user to have. A username Service with a
factory-set password of PRO@SERVICE can be utilized.
7. By clicking the “access rights“-tile you can check the needed rights.
8. Press multiple times “<“ or the home button in the upper left corner to
get back to the home screen.
4.1. Lost password
In case you have changed the password and do not remember what
you have selected. Please contact support at tss.finland@flaktgroup.
com and they can assist you reset it.
5 SETTINGS
5.1 Setting time
To set up the automatic testing you will first need to ensure your device
is set to the correct local time. If this needs to be changed, follow the
following steps.
1. Press the clock in the upper right corner.
2. Change to the desired time or check/uncheck the box for Network
Time Protocol to synchronize with time over ethernet.
3. If needed you can use the dropdown menu in the upper left corner
and press “Settings“ to get into more detailed time settings.
4. Select “System“ and then “Time“ to get into the time zone and
daylight savings settings.
5. First choose your time zone and daylight savings condition then set
the time to your local time.
6. Press multiple times “<“ or the home button in the upper left corner to
get back to the home screen
5.1.1. Changing the system test schedule
1. Login as admin
2. Select groups.
3. Edit the desired group using the pencil icon on the particular group.
4. Select the group test schedule.
5. Set desired damper test parameters (Enable/Disable, Interval, Day of
the week, Time
Note! The admin privileges are required to set the damper test
schedule.
Damper testing can only be set for groups. If an individual slave unit
should be tested, then the dampers of this slave unit need to be
assigned to an individual custom group first.
5.1.2 Manual test dampers
It is possible to carry out a manual test of all dampers, and groups of
dampers. For a group of dampers to be tested, the group must have
been created either during the set-up process or before you require
a set number of dampers to be tested as a group (see the FICO PRO
operation manual for further details of how to set up groups of dampers.
Dampers can be manually tested by pushing the test button on a multi-
box PCB. In this case, all the dampers connected to a particular multi-
box will be tested instantly and simultaneously.
The other way of a manual damper test is to execute it from the HMI of
FICO PRO. It is possible to test fire dampers manually one fire damper
group at a time.
1. Select ‘Groups’ tile from the home view.
2. Select a group to be manually tested.
3. Select ‘Test group’ to start damper testing.
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
6
FICO PRO - Operation Guide
SETTINGS, ACCESSORIES
5.2. Servicing dampers in the system
We recommend that the complete system should be put into standby
mode when you need to carry out any servicing to a damper. If this is
not feasible, it is recommended to at least set the multi-box to which
the serviceable fire damper is connected to service mode for the
duration of the service.
5.3. Alarms in the ISYteq FICO PRO
When an alarm has occurred within the system, a notification is shown
on the screen.
Types of alarms
Fire alarm – The complete system or a damper group is in full
alarm mode:
1. All dampers close
2. Only certain dampers close within a set group/s
Service alarm – An issue has occurred to the system:
1. A damper has failed to close
2. A damper has failed to open
3. Smoke detector is dirty
4. Smoke detector is disconnected
5. Smoke detector is a short circuit
Timeout alarm – An error with the communication to a multi-box/
boxes
The fan stopped – The fire alarm in the group or closed damper count
in the group exceeds the set value for the group
controlling the fan relay output. Or timed-out unit
count in the group exceeds the allowed set count for
the group controlling the fan relay output.
5.3.1. Alarms in a Multi-box
Status – Constantly illuminating = Power on and communicating with
FICO PRO,
Blinking = Power on but no communication with FICO PRO
Service - Constantly illuminating = Active service alarm
Alarm - Constantly illuminating = Active damper-generated fire alarm
Open - Constantly illuminating = The damper is open,
Blinking = The damper is opening
Closed - Constantly illuminating = The damper is closed,
Blinking = The damper is closing
Fire – A detector has been triggered due to a fire.
Service – A detector needs attention.
Link – LED briefly blinks when the unit communicates with FICO PRO
6 ACCESSORIES
6.1. FCIO-8
FCIO-8 unit is designed to be used as a slave unit with FICO-PRO fire
damper control systems. The unit cannot be used stand alone.
The FCIO-8 implements additional analogue/digital inputs or outputs to
the FICO system where additional IO is needed. Up to 63 units can be
connected to FICO-PRO (the total number of units in any mix supported
by FICO-PRO).
Note! Up to 8 units can be powered directly from FICO-PRO if digital
outputs are not used. More information is available from ‘Unit FCIO-8
Datasheet.
6.2. FCIO-88
FCIO-88 unit is designed to be used as a slave unit with a FICO-PRO
fire damper control system. The unit cannot be used stand-alone. The
FCIO-88 implements additional analogue/digital inputs or relay outputs
to the FICO system where additional IO is needed. Up to 63 units can be
connected to FICO-PRO (the total number of units in any mix supported
by FICO-PRO).
More information is available from ‘FCIO-88 Datasheet’.
6.3. Smoke detectors
6.3.1. FDKC-2 = UG-3-O Smoke detector for ducts, Optical, L = 600 mm
6.3.2. FDKC-4 = UG-3-O-M Smoke detector for ducts, Optical with
auxiliary fan
6.3.3. FDRC-2 = EVC-PY-DA Smoke detector for rooms, Optical + UB-6
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
7
FICO PRO - Operation Guide
CABLING REQUIREMENTS
7 CABLING REQUIREMENTS
Typical wiring drawings and connections of the ISYteq FICO PRO and the Multi-boxes FCBB-2 and FCBB-04
DAMPER 1
55
FICO-PRO
60 61
42 43 44 45 46 473 4 5 6 48 49 50 51 52 53
230VAC
Digital inputs Analog LINK 1 LINK 2
L N PE
X1 X3 Y1G G0 S1 S2 D0 D1 D0 D1
12 S1 S2 S4 S6
Supply
voltage
230VAC
Fire damper
MODBUS RTU
Ventilation duct detector
UG-3-O
7 8
S4 S6
DAMPER 2
9 10 11 12
G G0 S1 S2
13 14
S4 S6
1 2 S1 S2 S4 S6
Fire damper
DAMPER 3
15 16 17 18
G G0 S1 S2
12 S1 S2 S4 S6
Fire damper
19 20
S4 S6
DAMPER 4
21 22 23 24
G G0 S1 S2
25 26
S4 S6
1 2 S1 S2 S4 S6
Fire damper
27 28 29 30
DETECTOR
G1 M1 G2 M2
2 1 5
2.2KOhm
2 1 5
2.2KOhm
X2 X4
54
PWR
G
33 34 35 36 37 38 39 40
NO C NC NO NC
NC NO
31 32
NO C
NC
41
C
REL 1 REL 2 REL 3 REL 4
ETH 2
1 2
ETH 1
C
62
CONNECTION DRAWING
DEFAULT INPUT AND OUTPUT CONNECTIONS
FICO-PRO
42 43 44 45 46 47 48
Digital inputs Analog
X1 X3 Y1
X2 X4
33 34 35 36 37 38 39 40
NO C NC NO NC
NC NO
31 32
NO C
NC
41
C
REL 1 REL 2 REL 3 REL 4
C
Alarm Service FAN
External re alarm
External interlock
External test
Generic
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
8
FICO PRO - Operation Guide
CABLING REQUIREMENTS
60 61 62
230VAC
L N PE
Supply
230VAC
49 50 51 52 53 54
LINK 1 LINK 2
D0 D1 D0 D1
FICO-PRO
1 2 3
230VAC
L N PE
Supply
230VAC
34 35 36 37 38 39
LINK LINK
D0 D1 D0 D1
FCBB-2
1 2 3
230VAC
L N PE
Supply
230VAC
34 35 36 37 38 39
LINK LINK
D0 D1 D0 D1
FCBB-2
MODBUS RTU MODBUS RTU MODBUS RTU
Power cable
EQQ3x1,5
Communication cable
FQAR-PG 2x0.5 (1 twisted pair)
1..63 units
0..1200 m
60 61 62
230VAC
L N PE
Supply
230VAC
49 50 51 52 53 54
LINK 1 LINK 2
D0 D1 D0 D1
FICO-PRO
1 2 3
230VAC
L N PE
Supply
230VAC
36 37 38 39 40 41
LINK LINK
D0 D1 D0 D1
FCBB-4
1 2 3
230VAC
L N PE
Supply
230VAC
36 37 38 39 40 41
LINK LINK
D0 D1 D0 D1
FCBB-4
MODBUS RTU MODBUS RTU MODBUS RTU
Power cable
EQQ3x1,5
Communication cable
FQAR-PG 2x0.5 (1 twisted pair)
1..63 units
0..1200 m
SYSTEM CONNECTION DRAWING
FläktGroup DC_10797GB 20231010_R0 Specifications are subject to alteration without notice.
9
FICO PRO - Operation Guide
NOTES
8 NOTES
WWW.FLAKTGROUP.COM FICO PRO 10797
»
Learn more on www.flaktgroup.com
or contact one of our oices
FG_DC_10797GB_FICO PRO_OM_20231010_R0 © Copyright 2023 FläktGroup
FläktGroup is the European market leader for smart and energy eicient Indoor Air
and Critical Air solutions to support every application area. We oer our customers
innovative technologies, high quality and outstanding performance supported by
more than a century of accumulated industry experience. The widest product range
in the market, and strong market presence in 65 countries worldwide, guarantee
that we are always by your side, ready to deliver Excellence in Solutions.
PRODUCT FUNCTIONS BY FLÄKTGROUP
Air Treatment | Air Movement | Air Diusion | Air Distribution | Air Filtration
Air Management & ATD’s | Air Conditioning & Heating | Controls | Service
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

FläktGroup FICO PRO (FCLB-256) Installation guide

FläktGroup
Brand
FläktGroup
Model
FICO PRO (FCLB-256)
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents